Document the PMC pinctrl bindings for pad power state and signaling voltage configuration. Both nvidia,tegra186-pmc.txt and nvidia,tegra20-pmc.txt are modified as they both cover SoC generations for which these bindings apply.
Add a header defining Tegra PMC pad voltage configurations. Signed-off-by: Aapo Vienamo <avien...@nvidia.com> Acked-by: Jon Hunter <jonath...@nvidia.com> Reviewed-by: Rob Herring <r...@kernel.org> --- .../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 92 ++++++++++++++++++ .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 103 +++++++++++++++++++++ include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 ++++ 3 files changed, 213 insertions(+) create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt index 5a3bf7c..d7fed4d 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt @@ -34,3 +34,95 @@ Board DTS: pmc@c360000 { nvidia,invert-interrupt; }; + +== Pad Control == + +On Tegra SoCs a pad is a set of pins which are configured as a group. +The pin grouping is a fixed attribute of the hardware. The PMC can be +used to set pad power state and signaling voltage. A pad can be either +in active or power down mode. The support for power state and signaling +voltage configuration varies depending on the pad in question. 3.3 V and +1.8 V signaling voltages are supported on pins where software +controllable signaling voltage switching is available. + +Pad configurations are described is with pin configuration nodes which +are placed under the pmc node and they are referred to by the pinctrl +client properties. For more information see +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt. + +Following pads are present on Tegra186: +csia csib dsi mipi-bias +pex-clk-bias pex-clk3 pex-clk2 pex-clk1 +usb0 usb1 usb2 usb-bias +uart audio hsic dbg +hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv +sdmmc4 cam dsib dsic +dsid csic csid csie +dsif spi ufs dmic-hv +edp sdmmc1-hv sdmmc3-hv conn +audio-hv ao-hv + +Required pin configuration properties: + - pins: Must contain name of the pad(s) to be configured. + +Optional pin configuration properties: + - low-power-enable: Configure the pad into power down mode + - low-power-disable: Configure the pad into active mode + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + +Note: The power state can be configured on all of the above pads except + for ao-hv. Following pads have software configurable signaling + voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv, + ao-hv. + +Pad configuration state example: + pmc: pmc@7000e400 { + compatible = "nvidia,tegra186-pmc"; + reg = <0 0x0c360000 0 0x10000>, + <0 0x0c370000 0 0x10000>, + <0 0x0c380000 0 0x10000>, + <0 0x0c390000 0 0x10000>; + reg-names = "pmc", "wake", "aotag", "scratch"; + + ... + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1-hv"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + hdmi_off: hdmi-off { + pins = "hdmi"; + low-power-enable; + } + + hdmi_on: hdmi-on { + pins = "hdmi"; + low-power-disable; + } + }; + +Pinctrl client example: + sdmmc1: sdhci@3400000 { + ... + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; + + ... + + sor0: sor@15540000 { + ... + pinctrl-0 = <&hdmi_off>; + pinctrl-1 = <&hdmi_on>; + pinctrl-names = "hdmi-on", "hdmi-off"; + }; diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt index a74b37b..5363b90 100644 --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt @@ -195,3 +195,106 @@ Example: power-domains = <&pd_audio>; ... }; + +== Pad Control == + +On Tegra SoCs a pad is a set of pins which are configured as a group. +The pin grouping is a fixed attribute of the hardware. The PMC can be +used to set pad power state and signaling voltage. A pad can be either +in active or power down mode. The support for power state and signaling +voltage configuration varies depending on the pad in question. 3.3 V and +1.8 V signaling voltages are supported on pins where software +controllable signaling voltage switching is available. + +The pad configuration state nodes are placed under the pmc node and they +are referred to by the pinctrl client properties. For more information +see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt. +The pad name should be used as the value of the pins property in pin +configuration nodes. + +Following pads are present on Tegra124 and Tegra132: +audio bb cam comp +csia csb cse dsi +dsib dsic dsid hdmi +hsic hv lvds mipi-bias +nand pex-bias pex-clk1 pex-clk2 +pex-cntrl sdmmc1 sdmmc3 sdmmc4 +sys_ddc uart usb0 usb1 +usb2 usb_bias + +Following pads are present on Tegra210: +audio audio-hv cam csia +csib csic csid csie +csif dbg debug-nonao dmic +dp dsi dsib dsic +dsid emmc emmc2 gpio +hdmi hsic lvds mipi-bias +pex-bias pex-clk1 pex-clk2 pex-cntrl +sdmmc1 sdmmc3 spi spi-hv +uart usb0 usb1 usb2 +usb3 usb-bias + +Required pin configuration properties: + - pins: Must contain name of the pad(s) to be configured. + +Optional pin configuration properties: + - low-power-enable: Configure the pad into power down mode + - low-power-disable: Configure the pad into active mode + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 + or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages. + The values are defined in + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h. + +Note: The power state can be configured on all of the Tegra124 and + Tegra132 pads. None of the Tegra124 or Tegra132 pads support + signaling voltage switching. + +Note: All of the listed Tegra210 pads except pex-cntrl support power + state configuration. Signaling voltage switching is supported on + following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio, + pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart. + +Pad configuration state example: + pmc: pmc@7000e400 { + compatible = "nvidia,tegra210-pmc"; + reg = <0x0 0x7000e400 0x0 0x400>; + clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>; + clock-names = "pclk", "clk32k_in"; + + ... + + sdmmc1_3v3: sdmmc1-3v3 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>; + }; + + sdmmc1_1v8: sdmmc1-1v8 { + pins = "sdmmc1"; + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>; + }; + + hdmi_off: hdmi-off { + pins = "hdmi"; + low-power-enable; + } + + hdmi_on: hdmi-on { + pins = "hdmi"; + low-power-disable; + } + }; + +Pinctrl client example: + sdmmc1: sdhci@700b0000 { + ... + pinctrl-names = "sdmmc-3v3", "sdmmc-1v8"; + pinctrl-0 = <&sdmmc1_3v3>; + pinctrl-1 = <&sdmmc1_1v8>; + }; + ... + sor@54540000 { + ... + pinctrl-0 = <&hdmi_off>; + pinctrl-1 = <&hdmi_on>; + pinctrl-names = "hdmi-on", "hdmi-off"; + }; diff --git a/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h b/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h new file mode 100644 index 0000000..20f4340 --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * pinctrl-tegra-io-pad.h: Tegra I/O pad source voltage configuration constants + * pinctrl bindings. + * + * Copyright (c) 2018, NVIDIA CORPORATION. All rights reserved. + * + * Author: Aapo Vienamo <avien...@nvidia.com> + */ + +#ifndef _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H +#define _DT_BINDINGS_PINCTRL_TEGRA_IO_PAD_H + +/* Voltage levels of the I/O pad's source rail */ +#define TEGRA_IO_PAD_VOLTAGE_1V8 0 +#define TEGRA_IO_PAD_VOLTAGE_3V3 1 + +#endif -- 2.7.4