On 15 October 2018 20:09, Rob Herring wrote:
> On Wed, Oct 03, 2018 at 05:02:25PM +0100, Alan Douglas wrote:
> > Add DT binding documentation for Sierra PHY. The PHY supports
> > a number of different protocols, including PCIe and USB.
> >
> > The PHY lanes may be configured as single or multi-lane links.
> > Each link is treated as a separate sub-node. For example, if
> > there are 4 lanes in total the first 2 might be configured as
> > a multi-lane PCIe link while the other two are single lane
> > USB links, and in this case there would be 3 sub-nodes.
> >
> > There are two resets for the PHY block (one for APB register
> > access, one for the PHY link) and separate resets for each
> > link. For multi-lane links, the reset corresponds to the
> > reset line on the master lane, the resets on other lanes
> > have no effect.
> >
> > Signed-off-by: Alan Douglas <[email protected]>
> > ---
> > .../devicetree/bindings/phy/cdns-sierra-phy.txt | 68
> > ++++++++++++++++++++++
> > 1 file changed, 68 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/phy/cdns-sierra-phy.txt
> >
> > diff --git a/Documentation/devicetree/bindings/phy/cdns-sierra-phy.txt
> > b/Documentation/devicetree/bindings/phy/cdns-sierra-
> phy.txt
> > new file mode 100644
> > index 0000000..0e2f3e3
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/phy/cdns-sierra-phy.txt
> > @@ -0,0 +1,68 @@
> > +Cadence Sierra PHY
> > +-----------------------
> > +
> > +Required properties:
> > +- compatible: cdns,sierra-phy-t0
> > +- clocks: Must contain an entry in clock-names.
> > + See ../clocks/clock-bindings.txt for details.
> > +- clock-names: Must be "phy_clk"
> > +- resets: Must contain an entry for each in reset-names.
> > + See ../reset/reset.txt for details.
> > +- reset-names: Must include "sierra_reset" and "sierra_apb" and one
> > for each
> > + sub-node.
> > + "sierra_reset" must control the reset line to the PHY.
> > + "sierra_apb" must control the reset line to the APB PHY
> > + interface.
> > + The name of the reset for each sub-node should match the full
> > + name of the sub-node. The sub-node resets must control the
> > + reset line for the master lane of the sub-node.
>
> Add a resets property to the sub-nodes instead.
>
Will do. As far as I can see it prevents me using devm_reset_control_get()
though, so I need to work out the best way to put these resets on remove()
> > +- reg: register range for the PHY.
> > +- #address-cells: Must be 1
> > +- #size-cells: Must be 0
> > +
> > +Optional properties:
> > +- cdns,autoconf: A boolean property whose presence indicates that the
> > + PHY registers will be configured by hardware. If not
> > + present, all sub-node optional properties must be
> > + provided.
> > +
> > +Sub-nodes:
> > + Each group of PHY lanes with a single master lane should be represented
> > as
> > + a sub-node. Note that the actual configuration of each lane is
> > determined by
> > + hardware strapping, and must match the configuration specified here.
> > +
> > +Sub-node required properties:
> > +- #phy-cells: Generic PHY binding; must be 0.
> > +
> > +Sub-node optional properties:
> > +- reg: The master lane number. This is the lowest
> > numbered
> > + lane in the lane group.
>
> How do you name the nodes if this is optional?
>
I'll change this to be required.
Thanks for your comments,
Alan
> > +- cdns,num-lanes: Number of lanes in this group. From 1 to 4. The
> > + group is made up of consecutive lanes.
> > +- cdns,phy-type: Can be PHY_TYPE_PCIE or PHY_TYPE_USB3, depending on
> > + configuration of lanes.
> > +
> > +Example:
> > + pcie_phy4: pcie-phy@fd240000 {
> > + compatible = "cdns,sierra-phy-t0";
> > + reg = <0x0 0xfd240000 0x0 0x40000>;
> > + resets = <&phyrst 0>, <&phyrst 1>, <&phyrst 2>, <&phyrst 4>;
> > + reset-names = "sierra_reset", "sierra_apb",
> > + "pcie_phy@0", "pcie_phy@2";
> > + clocks = <&phyclock>;
> > + clock-names = "phy_clk";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pcie0_phy0: pcie-phy@0 {
> > + reg = <0>;
> > + cdns,num-lanes = <2>;
> > + #phy-cells = <0>;
> > + cdns,phy-type = <PHY_TYPE_PCIE>;
> > + };
> > + pcie0_phy1: pcie-phy@2 {
> > + reg = <2>;
> > + cdns,num-lanes = <1>;
> > + #phy-cells = <0>;
> > + cdns,phy-type = <PHY_TYPE_PCIE>;
> > + };
> > +
> > --
> > 1.9.0
> >
