The Smartlabs SML-5442TW is broadly similar to the P231 reference design but with the following differences:
- Yellow and Blue front-panel LEDs are available but disabled - Red/Green LED is used to signal off/on status - GPIOX_17 is set high to enable the QCA9377 wireless module - uart_AO can be accessed after opening the case; soldered pins exist Signed-off-by: Christian Hewitt <[email protected]> --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts | 316 +++++++++++++++++++++ 2 files changed, 317 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index c31f29d6..37d7dbd 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts new file mode 100644 index 0000000..a081984 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-sml5442tw.dts @@ -0,0 +1,316 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2016 Endless Computers, Inc. + * Author: Carlo Caione <[email protected]> + * Copyright (c) 2018 BayLibre, SAS + * Author: Neil Armstrong <[email protected]> + */ + +/dts-v1/; + +#include "meson-gxl-s905d.dtsi" + +/ { + compatible = "smartlabs,sml5442tw", "amlogic,s905d", "amlogic,meson-gxl"; + model = "Smartlabs SML-5442TW"; + + aliases { + serial0 = &uart_AO; + serial1 = &uart_A; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + yellow { + label = "sml5442tw:yellow"; + gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + blue { + label = "sml5442tw:blue"; + gpios = <&gpio GPIODV_28 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + green { + label = "sml5442tw:green"; + gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + red { + label = "sml5442tw:red"; + gpios = <&gpio GPIODV_27 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + hdmi_5v: regulator-hdmi-5v { + compatible = "regulator-fixed"; + + regulator-name = "HDMI_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-always-on; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + cvbs-connector { + compatible = "composite-video-connector"; + + port { + cvbs_connector_in: endpoint { + remote-endpoint = <&cvbs_vdac_out>; + }; + }; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "meson-gx-audio"; + + simple-audio-card,dai-link@0 { + /* HDMI Output */ + format = "i2s"; + mclk-fs = <256>; + bitclock-master = <&i2s_dai>; + frame-master = <&i2s_dai>; + plat { + sound-dai = <&aiu_i2s_dma>; + }; + + cpu { + sound-dai = <&i2s_dai>; + }; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&cec_AO { + status = "okay"; + pinctrl-0 = <&ao_cec_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +&cvbs_vdac_port { + cvbs_vdac_out: endpoint { + remote-endpoint = <&cvbs_connector_in>; + }; +}; + +ðmac { + status = "okay"; + phy-mode = "rmii"; + phy-handle = <&internal_phy>; +}; + +/* This will enable the bluetooth module */ +&gpio { + bt-en { + gpio-hog; + gpios = <GPIOX_17 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "bt-en"; + }; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; + hdmi-supply = <&hdmi_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&internal_phy { + pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; + linux,rc-map-name = "rc-o2cz-khamsin"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <100000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* This is connected to the Bluetooth module: */ +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; + +/* This UART is brought out to the debug header */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0 { + status = "okay"; +}; -- 2.7.4
