Hi Rob, Thanks for the review. Please find my responses inline.
Thanks, Jolly Shah > -----Original Message----- > From: Rob Herring [mailto:r...@kernel.org] > Sent: Tuesday, December 04, 2018 2:06 PM > To: Jolly Shah <jol...@xilinx.com> > Cc: mark.rutl...@arm.com; Michal Simek <mich...@xilinx.com>; Rajan Vaja > <raj...@xilinx.com>; Nava kishore Manne <na...@xilinx.com>; linux-arm- > ker...@lists.infradead.org; linux-kernel@vger.kernel.org; > devicet...@vger.kernel.org; Jolly Shah <jol...@xilinx.com> > Subject: Re: [PATCH 0/9] dt-bindings: Firmware node binding for ZynqMP core > > On Fri, Nov 16, 2018 at 03:56:50PM -0800, Jolly Shah wrote: > > Base firmware node and clock child node binding are part of mainline kernel. > This patchset adds documentation to describe rest of the firmware child node > bindings. > > Complete firmware DT node example is shown below for ease of > understanding: > > Shouldn't there be a fpga mgr node too? Called pcap IIRC. > [Jolly] As you suggested, we only added child nodes if the sub-functions have their own resources (clks, irqs, etc.). FPGA doesn't have any resources so not added . Firmware driver would still register it as mfd device to instantiate the driver. > > > > firmware { > > zynqmp_firmware: zynqmp-firmware { > > compatible = "xlnx,zynqmp-firmware"; > > method = "smc"; > > #power-domain-cells = <1>; > > #reset-cells = <1>; > > > > zynqmp_clk: clock-controller { > > #clock-cells = <1>; > > compatible = "xlnx,zynqmp-clk"; > > clocks = <&pss_ref_clk>, <&video_clk>, > <&pss_alt_ref_clk>, <&aux_ref_clk>, <>_crx_ref_clk>; > > clock-names = "pss_ref_clk", "video_clk", > "pss_alt_ref_clk","aux_ref_clk", "gt_crx_ref_clk"; > > }; > > > > zynqmp_power: zynqmp-power { > > compatible = "xlnx,zynqmp-power"; > > interrupts = <0 35 4>; > > }; > > > > nvmem_firmware { > > compatible = "xlnx,zynqmp-nvmem-fw"; > > #address-cells = <1>; > > #size-cells = <1>; > > > > /* Data cells */ > > soc_revision: soc_revision { > > reg = <0x0 0x4>; > > }; > > }; > > > > afi0: afi0 { > > compatible = "xlnx,afi-fpga"; > > config-afi = <0 2>, <1 1>, <2 1>; > > }; > > > > qspi: spi@ff0f0000 { > > Why is this under firmware node? [Jolly] Qspi is a user of eemi API provided by firmware node to perform privileged register writes. Alternatively, we can keep such user nodes outside of firmware node and keep nodes which firmware is provider for like clock, reset, pins and power. Please suggest. > > > compatible = "xlnx,zynqmp-qspi-1.0"; > > clock-names = "ref_clk", "pclk"; > > clocks = <&misc_clk &misc_clk>; > > interrupts = <0 15 4>; > > interrupt-parent = <&gic>; > > num-cs = <1>; > > reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000 > 0x8000000>; > > }; > > > > serdes: zynqmp_phy@fd400000 { > > And this? [Jolly] Same as above. > > > compatible = "xlnx,zynqmp-psgtr"; > > status = "okay"; > > reg = <0x0 0xfd400000 0x0 0x40000>, <0x0 0xfd3d0000 > 0x0 0x1000>, > > <0x0 0xff5e0000 0x0 0x1000>; > > reg-names = "serdes", "siou", "lpd"; > > > > lane0: lane@0 { > > #phy-cells = <4>; > > }; > > lane1: lane@1 { > > #phy-cells = <4>; > > }; > > lane2: lane@2 { > > #phy-cells = <4>; > > }; > > lane3: lane@3 { > > #phy-cells = <4>; > > }; > > }; > > > > pinctrl_uart1_default: uart1-default { > > This goes under a pinctrl node. [Jolly] Pincontrol node is not added as it doesn't have any resources. As I understand, you suggest to still add pincontrol node and this under pincontrol node. > > > mux { > > groups = "uart0_4_grp"; > > function = "uart0"; > > }; > > > > conf { > > groups = "uart0_4_grp"; > > slew-rate = <SLEW_RATE_SLOW>; > > io-standard = <IO_STANDARD_LVCMOS18>; > > }; > > > > conf-rx { > > pins = "MIO18"; > > bias-high-impedance; > > }; > > > > conf-tx { > > pins = "MIO19"; > > bias-disable; > > schmitt-cmos = <PIN_INPUT_TYPE_CMOS>; > > }; > > }; > > zynqmp-r5-remoteproc@0 { > > Wrong unit-address and this doesn't belong here. [Jolly] Again as it is one of the user of firmware APIs, its kept here. Alternatively, we can keep such user nodes outside of firmware node and keep nodes which firmware is provider for like clock, reset, pins and power. Please suggest. > > > compatible = "xlnx,zynqmp-r5-remoteproc-1.0"; > > 'remoteproc' is what the h/w block is called? [Jolly] The hw block is called rpu. Thanks, Jolly Shah > > > reg = <0x0 0xFFE00000 0x0 0x10000>, > > <0x0 0xFFE20000 0x0 0x10000>, > > <0x0 0xff340000 0x0 0x100>; > > reg-names = "tcm_a", "tcm_b", "ipi"; > > dma-ranges; > > core_conf = "split0"; > > memory-region = <&rproc_0_fw_reserved>, > > <&rproc_0_dma_reserved>; > > tcm-pnode-id = <0xf>, <0x10>; > > rpu-pnode-id = <0x7>; > > interrupt-parent = <&gic>; > > interrupts = <0 29 4>; > > }; > > }; > > };