This patch reformats the parameter list for stmpe device in a table-style so it is more clear to read.
Signed-off-by: Philippe Schenker <philippe.schen...@toradex.com> --- Changes in v4: - New separate precursor patch for holding reformatting Changes in v3: None Changes in v2: None .../bindings/input/touchscreen/stmpe.txt | 52 ++++++++++++------- .../devicetree/bindings/mfd/stmpe.txt | 14 ++--- 2 files changed, 41 insertions(+), 25 deletions(-) diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt index 127baa31a77a..1d3f84308142 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -5,24 +5,40 @@ Required properties: - compatible: "st,stmpe-ts" Optional properties: -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 - -> 144 clocks), recommended is 4. -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external - reference) -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 - samples, 3 -> 8 samples) -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended - is 3 -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of - the fractional part) recommended is 7 -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 - mA max, 1 -> 50 mA typical 80 mA max) +- st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 144 clocks + 3 -> 64 clocks +- st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC +- st,ref-sel : ADC reference source + 0 -> internal 1 -> external +- st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us 5 -> 5 ms + 1 -> 50 us 6 -> 10 ms + 2 -> 100 us 7 -> 50 ms + 3 -> 500 us + 4 -> 1 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us 5 -> 10 ms + 1 -> 100 us 6 for 50 ms + 2 -> 500 us 7 -> 100 ms + 3 -> 1 ms + 4 -> 5 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) Node name must be stmpe_touchscreen and should be child node of stmpe node to which it belongs. diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index c797c05cd3c2..a46e7177195d 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,15 +4,15 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - - reg : I2C/SPI address of the device + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" + - reg : I2C/SPI address of the device Optional properties: - - interrupts : The interrupt outputs from the controller - - interrupt-controller : Marks the device node as an interrupt controller - - wakeup-source : Marks the input device as wakable - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 - - irq-gpio : If present, which GPIO to use for event IRQ + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ Example: -- 2.19.2