A frequent side comment has been to remove the use of writel_relaxed,
readl_relaxed, and mb. This reduces driver complexity and the _relaxed
variants were not known to provide any noticeable performance benefit.
Signed-off-by: Ryan Case <ryandc...@chromium.org>
Reviewed-by: Evan Green <evgr...@chromium.org>
---
Changes in v2:
- Expanded commit message
- Coalesced lines where possible
drivers/tty/serial/qcom_geni_serial.c | 191 +++++++++++---------------
1 file changed, 80 insertions(+), 111 deletions(-)
diff --git a/drivers/tty/serial/qcom_geni_serial.c
b/drivers/tty/serial/qcom_geni_serial.c
index 2b1e73193dad..e2cb3f7d1a7c 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -230,7 +230,7 @@ static unsigned int qcom_geni_serial_get_mctrl(struct
uart_port *uport)
if (uart_console(uport) || !uart_cts_enabled(uport)) {
mctrl |= TIOCM_CTS;
} else {
- geni_ios = readl_relaxed(uport->membase + SE_GENI_IOS);
+ geni_ios = readl(uport->membase + SE_GENI_IOS);
if (!(geni_ios & IO2_DATA_IN))
mctrl |= TIOCM_CTS;
}
@@ -248,7 +248,7 @@ static void qcom_geni_serial_set_mctrl(struct uart_port
*uport,
if (!(mctrl & TIOCM_RTS))
uart_manual_rfr = UART_MANUAL_RFR_EN | UART_RFR_NOT_READY;
- writel_relaxed(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR);
+ writel(uart_manual_rfr, uport->membase + SE_UART_MANUAL_RFR);
}
static const char *qcom_geni_serial_get_type(struct uart_port *uport)
@@ -277,9 +277,6 @@ static bool qcom_geni_serial_poll_bit(struct uart_port
*uport,
unsigned int fifo_bits;
unsigned long timeout_us = 20000;
- /* Ensure polling is not re-ordered before the prior writes/reads */
- mb();
-
if (uport->private_data) {
port = to_dev_port(uport, uport);
baud = port->baud;
@@ -299,7 +296,7 @@ static bool qcom_geni_serial_poll_bit(struct uart_port
*uport,
*/
timeout_us = DIV_ROUND_UP(timeout_us, 10) * 10;
while (timeout_us) {
- reg = readl_relaxed(uport->membase + offset);
+ reg = readl(uport->membase + offset);
if ((bool)(reg & field) == set)
return true;
udelay(10);
@@ -312,7 +309,7 @@ static void qcom_geni_serial_setup_tx(struct uart_port
*uport, u32 xmit_size)
{
u32 m_cmd;
- writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
+ writel(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
m_cmd = UART_START_TX << M_OPCODE_SHFT;
writel(m_cmd, uport->membase + SE_GENI_M_CMD0);
}
@@ -325,13 +322,13 @@ static void qcom_geni_serial_poll_tx_done(struct
uart_port *uport)
done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_DONE_EN, true);
if (!done) {
- writel_relaxed(M_GENI_CMD_ABORT, uport->membase +
+ writel(M_GENI_CMD_ABORT, uport->membase +
SE_GENI_M_CMD_CTRL_REG);
irq_clear |= M_CMD_ABORT_EN;
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
}
- writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
+ writel(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_abort_rx(struct uart_port *uport)
@@ -341,8 +338,8 @@ static void qcom_geni_serial_abort_rx(struct uart_port
*uport)
writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_ABORT, false);
- writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
- writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
+ writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ writel(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
}
#ifdef CONFIG_CONSOLE_POLL
@@ -351,19 +348,13 @@ static int qcom_geni_serial_get_char(struct uart_port
*uport)
u32 rx_fifo;
u32 status;
- status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
- writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
-
- status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
- writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ status = readl(uport->membase + SE_GENI_M_IRQ_STATUS);
+ writel(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
- /*
- * Ensure the writes to clear interrupts is not re-ordered after
- * reading the data.
- */
- mb();
+ status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
+ writel(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
- status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
+ status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS);
if (!(status & RX_FIFO_WC_MSK))
return NO_POLL_CHAR;
@@ -376,13 +367,12 @@ static void qcom_geni_serial_poll_put_char(struct
uart_port *uport,
{
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
- writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
+ writel(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, 1);
WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_TX_FIFO_WATERMARK_EN, true));
- writel_relaxed(c, uport->membase + SE_GENI_TX_FIFOn);
- writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
- SE_GENI_M_IRQ_CLEAR);
+ writel(c, uport->membase + SE_GENI_TX_FIFOn);
+ writel(M_TX_FIFO_WATERMARK_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
qcom_geni_serial_poll_tx_done(uport);
}
#endif
@@ -390,7 +380,7 @@ static void qcom_geni_serial_poll_put_char(struct uart_port
*uport,
#ifdef CONFIG_SERIAL_QCOM_GENI_CONSOLE
static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch)
{
- writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn);
+ writel(ch, uport->membase + SE_GENI_TX_FIFOn);
}
static void
@@ -409,7 +399,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport,
const char *s,
bytes_to_send++;
}
- writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+ writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
qcom_geni_serial_setup_tx(uport, bytes_to_send);
for (i = 0; i < count; ) {
size_t chars_to_write = 0;
@@ -427,7 +417,7 @@ __qcom_geni_serial_console_write(struct uart_port *uport,
const char *s,
chars_to_write = min_t(size_t, count - i, avail / 2);
uart_console_write(uport, s + i, chars_to_write,
qcom_geni_serial_wr_char);
- writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
+ writel(M_TX_FIFO_WATERMARK_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
i += chars_to_write;
}
@@ -456,7 +446,7 @@ static void qcom_geni_serial_console_write(struct console
*co, const char *s,
else
spin_lock_irqsave(&uport->lock, flags);
- geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ geni_status = readl(uport->membase + SE_GENI_STATUS);
/* Cancel the current write to log the fault */
if (!locked) {
@@ -466,11 +456,10 @@ static void qcom_geni_serial_console_write(struct console
*co, const char *s,
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
- writel_relaxed(M_CMD_ABORT_EN, uport->membase +
+ writel(M_CMD_ABORT_EN, uport->membase +
SE_GENI_M_IRQ_CLEAR);
}
- writel_relaxed(M_CMD_CANCEL_EN, uport->membase +
- SE_GENI_M_IRQ_CLEAR);
+ writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
} else if ((geni_status & M_GENI_CMD_ACTIVE) && !port->tx_remaining) {
/*
* It seems we can't interrupt existing transfers if all data
@@ -479,9 +468,8 @@ static void qcom_geni_serial_console_write(struct console
*co, const char *s,
qcom_geni_serial_poll_tx_done(uport);
if (uart_circ_chars_pending(&uport->state->xmit)) {
- irq_en = readl_relaxed(uport->membase +
- SE_GENI_M_IRQ_EN);
- writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN,
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
+ writel(irq_en | M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
}
@@ -585,12 +573,12 @@ static void qcom_geni_serial_start_tx(struct uart_port
*uport)
if (!qcom_geni_serial_tx_empty(uport))
return;
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
- writel_relaxed(port->tx_wm, uport->membase +
+ writel(port->tx_wm, uport->membase +
SE_GENI_TX_WATERMARK_REG);
- writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
}
@@ -600,35 +588,28 @@ static void qcom_geni_serial_stop_tx(struct uart_port
*uport)
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~M_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
irq_en &= ~M_TX_FIFO_WATERMARK_EN;
- writel_relaxed(0, uport->membase +
+ writel(0, uport->membase +
SE_GENI_TX_WATERMARK_REG);
}
- writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
- status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ status = readl(uport->membase + SE_GENI_STATUS);
/* Possible stop tx is called multiple times. */
if (!(status & M_GENI_CMD_ACTIVE))
return;
- /*
- * Ensure cancel command write is not re-ordered before checking
- * the status of the Primary Sequencer.
- */
- mb();
-
geni_se_cancel_m_cmd(&port->se);
if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_CANCEL_EN, true)) {
geni_se_abort_m_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
M_CMD_ABORT_EN, true);
- writel_relaxed(M_CMD_ABORT_EN, uport->membase +
- SE_GENI_M_IRQ_CLEAR);
+ writel(M_CMD_ABORT_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
- writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+ writel(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
}
static void qcom_geni_serial_start_rx(struct uart_port *uport)
@@ -637,26 +618,20 @@ static void qcom_geni_serial_start_rx(struct uart_port
*uport)
u32 status;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
- status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ status = readl(uport->membase + SE_GENI_STATUS);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_stop_rx(uport);
- /*
- * Ensure setup command write is not re-ordered before checking
- * the status of the Secondary Sequencer.
- */
- mb();
-
geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
if (port->xfer_mode == GENI_SE_FIFO) {
- irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN);
irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN;
- writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+ writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
- writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
}
@@ -668,31 +643,25 @@ static void qcom_geni_serial_stop_rx(struct uart_port
*uport)
u32 irq_clear = S_CMD_DONE_EN;
if (port->xfer_mode == GENI_SE_FIFO) {
- irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_S_IRQ_EN);
irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN);
- writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+ writel(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
- writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
}
- status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ status = readl(uport->membase + SE_GENI_STATUS);
/* Possible stop rx is called multiple times. */
if (!(status & S_GENI_CMD_ACTIVE))
return;
- /*
- * Ensure cancel command write is not re-ordered before checking
- * the status of the Secondary Sequencer.
- */
- mb();
-
geni_se_cancel_s_cmd(&port->se);
qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
S_GENI_CMD_CANCEL, false);
- status = readl_relaxed(uport->membase + SE_GENI_STATUS);
- writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ status = readl(uport->membase + SE_GENI_STATUS);
+ writel(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (status & S_GENI_CMD_ACTIVE)
qcom_geni_serial_abort_rx(uport);
}
@@ -706,7 +675,7 @@ static void qcom_geni_serial_handle_rx(struct uart_port
*uport, bool drop)
u32 total_bytes;
struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
- status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
+ status = readl(uport->membase + SE_GENI_RX_FIFO_STATUS);
word_cnt = status & RX_FIFO_WC_MSK;
last_word_partial = status & RX_LAST;
last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >>
@@ -736,7 +705,7 @@ static void qcom_geni_serial_handle_tx(struct uart_port
*uport, bool done,
unsigned int chunk;
int tail;
- status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
+ status = readl(uport->membase + SE_GENI_TX_FIFO_STATUS);
/* Complete the current tx command before taking newly added data */
if (active)
@@ -762,9 +731,9 @@ static void qcom_geni_serial_handle_tx(struct uart_port
*uport, bool done,
qcom_geni_serial_setup_tx(uport, pending);
port->tx_remaining = pending;
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
if (!(irq_en & M_TX_FIFO_WATERMARK_EN))
- writel_relaxed(irq_en | M_TX_FIFO_WATERMARK_EN,
+ writel(irq_en | M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
@@ -797,14 +766,14 @@ static void qcom_geni_serial_handle_tx(struct uart_port
*uport, bool done,
* cleared it in qcom_geni_serial_isr it will have already reasserted
* so we must clear it again here after our writes.
*/
- writel_relaxed(M_TX_FIFO_WATERMARK_EN,
+ writel(M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_CLEAR);
out_write_wakeup:
if (!port->tx_remaining) {
- irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
if (irq_en & M_TX_FIFO_WATERMARK_EN)
- writel_relaxed(irq_en & ~M_TX_FIFO_WATERMARK_EN,
+ writel(irq_en & ~M_TX_FIFO_WATERMARK_EN,
uport->membase + SE_GENI_M_IRQ_EN);
}
@@ -828,12 +797,12 @@ static irqreturn_t qcom_geni_serial_isr(int isr, void
*dev)
return IRQ_NONE;
spin_lock_irqsave(&uport->lock, flags);
- m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
- s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
- geni_status = readl_relaxed(uport->membase + SE_GENI_STATUS);
- m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
- writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
- writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ m_irq_status = readl(uport->membase + SE_GENI_M_IRQ_STATUS);
+ s_irq_status = readl(uport->membase + SE_GENI_S_IRQ_STATUS);
+ geni_status = readl(uport->membase + SE_GENI_STATUS);
+ m_irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
+ writel(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
+ writel(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
goto out_unlock;
@@ -931,7 +900,7 @@ static int qcom_geni_serial_port_setup(struct uart_port
*uport)
get_tx_fifo_size(port);
set_rfr_wm(port);
- writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
+ writel(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
/*
* Make an unconditional cancel on the main sequencer to reset
* it else we could end up in data loss scenarios.
@@ -1035,10 +1004,10 @@ static void qcom_geni_serial_set_termios(struct
uart_port *uport,
ser_clk_cfg |= clk_div << CLK_DIV_SHFT;
/* parity */
- tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG);
- tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG);
- rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG);
- rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG);
+ tx_trans_cfg = readl(uport->membase + SE_UART_TX_TRANS_CFG);
+ tx_parity_cfg = readl(uport->membase + SE_UART_TX_PARITY_CFG);
+ rx_trans_cfg = readl(uport->membase + SE_UART_RX_TRANS_CFG);
+ rx_parity_cfg = readl(uport->membase + SE_UART_RX_PARITY_CFG);
if (termios->c_cflag & PARENB) {
tx_trans_cfg |= UART_TX_PAR_EN;
rx_trans_cfg |= UART_RX_PAR_EN;
@@ -1094,17 +1063,17 @@ static void qcom_geni_serial_set_termios(struct
uart_port *uport,
uart_update_timeout(uport, termios->c_cflag, baud);
if (!uart_console(uport))
- writel_relaxed(port->loopback,
+ writel(port->loopback,
uport->membase + SE_UART_LOOPBACK_CFG);
- writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
- writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
- writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
- writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
- writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
- writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
- writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
- writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
- writel_relaxed(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
+ writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
+ writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
+ writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
+ writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
+ writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
+ writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
+ writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
+ writel(ser_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
+ writel(ser_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
out_restart_rx:
qcom_geni_serial_start_rx(uport);
}
@@ -1195,13 +1164,13 @@ static int __init
qcom_geni_serial_earlycon_setup(struct earlycon_device *dev,
geni_se_init(&se, DEF_FIFO_DEPTH_WORDS / 2, DEF_FIFO_DEPTH_WORDS - 2);
geni_se_select_mode(&se, GENI_SE_FIFO);
- writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
- writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
- writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
- writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
- writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
- writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
- writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
+ writel(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
+ writel(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
+ writel(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
+ writel(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
+ writel(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
+ writel(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
+ writel(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
dev->con->write = qcom_geni_serial_earlycon_write;
dev->con->setup = NULL;
--
2.20.1.97.g81188d93c3-goog
