On 28/01/2019 06:06, Sameer Pujar wrote:
>
> On 1/25/2019 7:34 PM, Jon Hunter wrote:
>> On 25/01/2019 13:58, Takashi Iwai wrote:
>>> On Fri, 25 Jan 2019 14:26:27 +0100,
>>> Jon Hunter wrote:
>>>>
>>>> On 25/01/2019 12:40, Takashi Iwai wrote:
>>>>> On Fri, 25 Jan 2019 12:36:00 +0100,
>>>>> Jon Hunter wrote:
>>>>>>
>>>>>> On 24/01/2019 19:08, Takashi Iwai wrote:
>>>>>>> On Thu, 24 Jan 2019 18:36:43 +0100,
>>>>>>> Sameer Pujar wrote:
>>>>>>>> If CONFIG_PM is disabled or runtime PM calls are forbidden, the
>>>>>>>> clocks
>>>>>>>> will not be ON. This could cause issue during probe, where hda init
>>>>>>>> setup is done. This patch checks whether runtime PM is enabled
>>>>>>>> or not.
>>>>>>>> If disabled, clocks are enabled in probe() and disabled in remove()
>>>>>>>>
>>>>>>>> This patch does following minor changes as cleanup,
>>>>>>>> * return code check for pm_runtime_get_sync() to take care of
>>>>>>>> failure
>>>>>>>> and exit gracefully.
>>>>>>>> * In remove path runtime PM is disabled before calling
>>>>>>>> snd_card_free().
>>>>>>>> * hda_tegra_disable_clocks() is moved out of CONFIG_PM_SLEEP
>>>>>>>> check.
>>>>>>>> * runtime PM callbacks moved out of CONFIG_PM check
>>>>>>>>
>>>>>>>> Signed-off-by: Sameer Pujar <spu...@nvidia.com>
>>>>>>>> Reviewed-by: Ravindra Lokhande <rlokha...@nvidia.com>
>>>>>>>> Reviewed-by: Jon Hunter <jonath...@nvidia.com>
>>>>>>> (snip)
>>>>>>>> @@ -555,6 +553,13 @@ static int hda_tegra_probe(struct
>>>>>>>> platform_device *pdev)
>>>>>>>> if (!azx_has_pm_runtime(chip))
>>>>>>>> pm_runtime_forbid(hda->dev);
>>>>>>>> + /* explicit resume if runtime PM is disabled */
>>>>>>>> + if (!pm_runtime_enabled(hda->dev)) {
>>>>>>>> + err = hda_tegra_runtime_resume(hda->dev);
>>>>>>>> + if (err)
>>>>>>>> + goto out_free;
>>>>>>>> + }
>>>>>>>> +
>>>>>>>> schedule_work(&hda->probe_work);
>>>>>>> Calling runtime_resume here is really confusing...
>>>>>> Why? IMO it is better to have a single handler for resuming the
>>>>>> device
>>>>>> and so if RPM is not enabled we call the handler directly. This is
>>>>>> what
>>>>>> we have been advised to do in the past and do in other drivers.
>>>>>> See ...
>>>>> The point is that we're not "resuming" anything there. It's in the
>>>>> early probe stage, and the device state is uninitialized, not really
>>>>> suspended. It'd end up with just calling the same helper
>>>>> (hda_tegra_enable_clocks()), though.
>>>> Yes and you can make the same argument for every driver that calls
>>>> pm_runtime_get_sync() during probe to turn on clocks, handle resets,
>>>> etc, because at the end of the day the very first call to
>>>> pm_runtime_get_sync() invokes the runtime_resume callback, when we have
>>>> never been suspended.
>>> Although there are some magical pm_runtime_*() in some places, most of
>>> such pm_runtime_get_sync() is for the actual runtime PM management (to
>>> prevent the runtime suspend), while the code above is for explicitly
>>> setting up something for non-PM cases.
>>>
>>> And if pm_runtime_get_sync() is obviously superfluous, we should
>>> remove such calls. Really.
>> Yes agree.
>>
>>>> Yes at the end of the day it is the same and given that we have done
>>>> this elsewhere I think it is good to be consistent if/where we can.
>>> The code becomes less readable, and that's a good reason against it :)
>> I don't its less readable. However, I do think it is less error prone :-)
>
> Do we have a consensus here? Request others to provide opinions to help
> close on this.
I am not going to block this and ultimately it is Iwai-san call.
However, I wonder if it would be appropriate to move the whole ...
if (pm_runtime_enabled())
ret = pm_runtime_get_sync();
else
ret = hda_tegra_runtime_resume();
... into the probe_work function? In other words, we are just resuming
when we really need to. Unless I am still misunderstanding Iwai-san
comment. Otherwise if Iwai-san is happy with V2 then go with that.
Cheers
Jon
--
nvpublic
