Hi,
On 25/01/19 4:55 PM, Thierry Reding wrote:
> From: JC Kuo <[email protected]>
>
> Add support for the XUSB pad controller found on Tegra186 SoCs. It is
> mostly similar to the same IP found on earlier chips, but the number of
> pads exposed differs, as do the programming sequences.
>
> Note that the DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL power
> supplies of the XUSB pad controller require strict power sequencing and
> are therefore controlled by the PMIC on Tegra186.
>
> Signed-off-by: JC Kuo <[email protected]>
> Signed-off-by: Thierry Reding <[email protected]>
> ---
> MAINTAINERS | 5 +
> drivers/phy/tegra/Makefile | 1 +
> drivers/phy/tegra/xusb-tegra186.c | 908 ++++++++++++++++++++++++++++++
> drivers/phy/tegra/xusb.c | 6 +
> drivers/phy/tegra/xusb.h | 27 +
> 5 files changed, 947 insertions(+)
> create mode 100644 drivers/phy/tegra/xusb-tegra186.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index ddcdc29dfe1f..754f7e757361 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -15099,6 +15099,11 @@ M: Laxman Dewangan <[email protected]>
> S: Supported
> F: drivers/spi/spi-tegra*
>
> +TEGRA XUSB PADCTL DRIVER
> +M: JC Kuo <[email protected]>
> +S: Supported
> +F: drivers/phy/tegra/xusb*
> +
> TEHUTI ETHERNET DRIVER
> M: Andy Gospodarek <[email protected]>
> L: [email protected]
> diff --git a/drivers/phy/tegra/Makefile b/drivers/phy/tegra/Makefile
> index 898589238fd9..a93cd9a499b2 100644
> --- a/drivers/phy/tegra/Makefile
> +++ b/drivers/phy/tegra/Makefile
> @@ -4,3 +4,4 @@ phy-tegra-xusb-y += xusb.o
> phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_124_SOC) += xusb-tegra124.o
> phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_132_SOC) += xusb-tegra124.o
> phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_210_SOC) += xusb-tegra210.o
> +phy-tegra-xusb-$(CONFIG_ARCH_TEGRA_186_SOC) += xusb-tegra186.o
> diff --git a/drivers/phy/tegra/xusb-tegra186.c
> b/drivers/phy/tegra/xusb-tegra186.c
> new file mode 100644
> index 000000000000..0dbcaddade90
> --- /dev/null
> +++ b/drivers/phy/tegra/xusb-tegra186.c
> @@ -0,0 +1,908 @@
> +/*
> + * Copyright (c) 2016, NVIDIA CORPORATION. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> + */
please use SPDX license format.
> +
> +#include <linux/delay.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/phy/phy.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/platform_device.h>
> +#include <linux/clk.h>
> +#include <linux/slab.h>
> +
> +#include <soc/tegra/fuse.h>
> +
> +#include "xusb.h"
> +
> +/* FUSE USB_CALIB registers */
> +#define HS_CURR_LEVEL_PADX_SHIFT(x) ((x) ? (11 + (x - 1) * 6) : 0)
> +#define HS_CURR_LEVEL_PAD_MASK 0x3f
> +#define HS_TERM_RANGE_ADJ_SHIFT 7
> +#define HS_TERM_RANGE_ADJ_MASK 0xf
> +#define HS_SQUELCH_SHIFT 29
> +#define HS_SQUELCH_MASK 0x7
> +
> +#define RPD_CTRL_SHIFT 0
> +#define RPD_CTRL_MASK 0x1f
> +
> +/* XUSB PADCTL registers */
> +#define XUSB_PADCTL_USB2_PAD_MUX 0x4
> +#define USB2_PORT_SHIFT(x) ((x) * 2)
> +#define USB2_PORT_MASK 0x3
> +#define PORT_XUSB 1
> +#define HSIC_PORT_SHIFT(x) ((x) + 20)
> +#define HSIC_PORT_MASK 0x1
> +#define PORT_HSIC 0
> +
> +#define XUSB_PADCTL_USB2_PORT_CAP 0x8
> +#define XUSB_PADCTL_SS_PORT_CAP 0xc
> +#define PORTX_CAP_SHIFT(x) ((x) * 4)
> +#define PORT_CAP_MASK 0x3
> +#define PORT_CAP_DISABLED 0x0
> +#define PORT_CAP_HOST 0x1
> +#define PORT_CAP_DEVICE 0x2
> +#define PORT_CAP_OTG 0x3
> +
> +#define XUSB_PADCTL_ELPG_PROGRAM 0x20
> +#define USB2_PORT_WAKE_INTERRUPT_ENABLE(x) (1 << (x))
Use BIT() macros here and below
> +#define USB2_PORT_WAKEUP_EVENT(x) ( 1 << ((x) + 7))
> +#define SS_PORT_WAKE_INTERRUPT_ENABLE(x) (1 << ((x) + 14))
> +#define SS_PORT_WAKEUP_EVENT(x) (1 << ((x) + 21))
> +#define USB2_HSIC_PORT_WAKE_INTERRUPT_ENABLE(x) (1 << ((x) + 28))
> +#define USB2_HSIC_PORT_WAKEUP_EVENT(x) (1 << ((x) +
> 30))
> +#define ALL_WAKE_EVENTS \
> + (USB2_PORT_WAKEUP_EVENT(0) | USB2_PORT_WAKEUP_EVENT(1) | \
> + USB2_PORT_WAKEUP_EVENT(2) | SS_PORT_WAKEUP_EVENT(0) | \
> + SS_PORT_WAKEUP_EVENT(1) | SS_PORT_WAKEUP_EVENT(2) | \
> + USB2_HSIC_PORT_WAKEUP_EVENT(0))
> +
> +#define XUSB_PADCTL_ELPG_PROGRAM_1 0x24
> +#define SSPX_ELPG_CLAMP_EN(x) (1 << (0 + (x) * 3))
> +#define SSPX_ELPG_CLAMP_EN_EARLY(x) (1 << (1 + (x) * 3))
> +#define SSPX_ELPG_VCORE_DOWN(x) (1 << (2 + (x) * 3))
> +
> +#define XUSB_PADCTL_USB2_OTG_PADX_CTL0(x) (0x88 + (x) * 0x40)
> +#define HS_CURR_LEVEL(x) ((x) & 0x3f)
> +#define TERM_SEL (1 << 25)
> +#define USB2_OTG_PD (1 << 26)
> +#define USB2_OTG_PD2 (1 << 27)
> +#define USB2_OTG_PD2_OVRD_EN (1 << 28)
> +#define USB2_OTG_PD_ZI (1 << 29)
> +
> +#define XUSB_PADCTL_USB2_OTG_PADX_CTL1(x) (0x8c + (x) * 0x40)
> +#define USB2_OTG_PD_DR (1 << 2)
> +#define TERM_RANGE_ADJ(x) (((x) & 0xf) << 3)
> +#define RPD_CTRL(x) (((x) & 0x1f) << 26)
> +
> +#define XUSB_PADCTL_USB2_BIAS_PAD_CTL0 0x284
> +#define BIAS_PAD_PD (1 << 11)
> +#define HS_SQUELCH_LEVEL(x) (((x) & 0x7) << 0)
> +
> +#define XUSB_PADCTL_USB2_BIAS_PAD_CTL1 0x288
> +#define USB2_TRK_START_TIMER(x) (((x) & 0x7f) << 12)
> +#define USB2_TRK_DONE_RESET_TIMER(x) (((x) & 0x7f) << 19)
> +#define USB2_PD_TRK (1 << 26)
> +
> +#define XUSB_PADCTL_HSIC_PADX_CTL0(x) (0x300 + (x) * 0x20)
> +#define HSIC_PD_TX_DATA0 (1 << 1)
> +#define HSIC_PD_TX_STROBE (1 << 3)
> +#define HSIC_PD_RX_DATA0 (1 << 4)
> +#define HSIC_PD_RX_STROBE (1 << 6)
> +#define HSIC_PD_ZI_DATA0 (1 << 7)
> +#define HSIC_PD_ZI_STROBE (1 << 9)
> +#define HSIC_RPD_DATA0 (1 << 13)
> +#define HSIC_RPD_STROBE (1 << 15)
> +#define HSIC_RPU_DATA0 (1 << 16)
> +#define HSIC_RPU_STROBE (1 << 18)
> +
> +#define XUSB_PADCTL_HSIC_PAD_TRK_CTL0 (0x340)
unnecessary ().
> +#define HSIC_TRK_START_TIMER(x) (((x) & 0x7f) << 5)
> +#define HSIC_TRK_DONE_RESET_TIMER(x) (((x) & 0x7f) << 12)
> +#define HSIC_PD_TRK (1 << 19)
> +
> +#define USB2_VBUS_ID (0x360)
here too..
> +#define VBUS_OVERRIDE (1 << 14)
> +#define ID_OVERRIDE(x) (((x) & 0xf) << 18)
> +#define ID_OVERRIDE_FLOATING ID_OVERRIDE(8)
> +#define ID_OVERRIDE_GROUNDED ID_OVERRIDE(0)
> +
> +#define TEGRA186_LANE(_name, _offset, _shift, _mask, _type) \
> + { \
> + .name = _name, \
> + .offset = _offset, \
> + .shift = _shift, \
> + .mask = _mask, \
> + .num_funcs = ARRAY_SIZE(tegra186_##_type##_functions), \
> + .funcs = tegra186_##_type##_functions, \
> + }
> +
> +struct tegra_xusb_fuse_calibration {
> + u32 *hs_curr_level;
> + u32 hs_squelch;
> + u32 hs_term_range_adj;
> + u32 rpd_ctrl;
> +};
> +
> +struct tegra186_xusb_padctl {
> + struct tegra_xusb_padctl base;
> +
> + struct tegra_xusb_fuse_calibration calib;
> +
> + /* UTMI bias and tracking */
> + struct clk *usb2_trk_clk;
> + unsigned int bias_pad_enable;
> +};
> +
> +static inline struct tegra186_xusb_padctl *
> +to_tegra186_xusb_padctl(struct tegra_xusb_padctl *padctl)
> +{
> + return container_of(padctl, struct tegra186_xusb_padctl, base);
> +}
> +
> +/* USB 2.0 UTMI PHY support */
> +static struct tegra_xusb_lane *
> +tegra186_usb2_lane_probe(struct tegra_xusb_pad *pad, struct device_node *np,
> + unsigned int index)
> +{
> + struct tegra_xusb_usb2_lane *usb2;
> + int err;
> +
> + usb2 = kzalloc(sizeof(*usb2), GFP_KERNEL);
> + if (!usb2)
> + return ERR_PTR(-ENOMEM);
> +
> + INIT_LIST_HEAD(&usb2->base.list);
> + usb2->base.soc = &pad->soc->lanes[index];
> + usb2->base.index = index;
> + usb2->base.pad = pad;
> + usb2->base.np = np;
> +
> + err = tegra_xusb_lane_parse_dt(&usb2->base, np);
> + if (err < 0) {
> + kfree(usb2);
> + return ERR_PTR(err);
> + }
> +
> + return &usb2->base;
> +}
> +
> +static void tegra186_usb2_lane_remove(struct tegra_xusb_lane *lane)
> +{
> + struct tegra_xusb_usb2_lane *usb2 = to_usb2_lane(lane);
> +
> + kfree(usb2);
> +}
> +
> +static const struct tegra_xusb_lane_ops tegra186_usb2_lane_ops = {
> + .probe = tegra186_usb2_lane_probe,
> + .remove = tegra186_usb2_lane_remove,
> +};
> +
> +static void tegra186_utmi_bias_pad_power_on(struct tegra_xusb_padctl *padctl)
> +{
> + struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
> + struct device *dev = padctl->dev;
> + u32 value;
> + int err;
> +
> + mutex_lock(&padctl->lock);
> +
> + if (priv->bias_pad_enable++ > 0) {
> + mutex_unlock(&padctl->lock);
> + return;
> + }
> +
> + err = clk_prepare_enable(priv->usb2_trk_clk);
> + if (err < 0)
> + dev_warn(dev, "failed to enable USB2 trk clock: %d\n", err);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> + value &= ~USB2_TRK_START_TIMER(~0);
> + value |= USB2_TRK_START_TIMER(0x1e);
> + value &= ~USB2_TRK_DONE_RESET_TIMER(~0);
> + value |= USB2_TRK_DONE_RESET_TIMER(0xa);
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL0);
> + value &= ~BIAS_PAD_PD;
> + value &= ~HS_SQUELCH_LEVEL(~0);
> + value |= HS_SQUELCH_LEVEL(priv->calib.hs_squelch);
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL0);
> +
> + udelay(1);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> + value &= ~USB2_PD_TRK;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> +
> + mutex_unlock(&padctl->lock);
> +}
> +
> +static void tegra186_utmi_bias_pad_power_off(struct tegra_xusb_padctl
> *padctl)
> +{
> + struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
> + u32 value;
> +
> + mutex_lock(&padctl->lock);
> +
> + if (WARN_ON(priv->bias_pad_enable == 0)) {
> + mutex_unlock(&padctl->lock);
> + return;
> + }
> +
> + if (--priv->bias_pad_enable > 0) {
> + mutex_unlock(&padctl->lock);
> + return;
> + }
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> + value |= USB2_PD_TRK;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_BIAS_PAD_CTL1);
> +
> + clk_disable_unprepare(priv->usb2_trk_clk);
> +
> + mutex_unlock(&padctl->lock);
> +}
> +
> +void tegra_phy_xusb_utmi_pad_power_on(struct phy *phy)
> +{
> + struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
> + struct tegra_xusb_padctl *padctl = lane->pad->padctl;
> + struct tegra_xusb_usb2_port *port;
> + struct device *dev = padctl->dev;
> + unsigned int index = lane->index;
> + u32 value;
> +
> + if (!phy)
> + return;
> +
> + port = tegra_xusb_find_usb2_port(padctl, index);
> + if (!port) {
> + dev_err(dev, "no port found for USB2 lane %u\n", index);
> + return;
> + }
> +
> + tegra186_utmi_bias_pad_power_on(padctl);
> +
> + udelay(2);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> + value &= ~USB2_OTG_PD;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> + value &= ~USB2_OTG_PD_DR;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> +}
> +
> +void tegra_phy_xusb_utmi_pad_power_down(struct phy *phy)
> +{
> + struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
> + struct tegra_xusb_padctl *padctl = lane->pad->padctl;
> + unsigned int index = lane->index;
> + u32 value;
> +
> + if (!phy)
> + return;
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> + value |= USB2_OTG_PD;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> + value |= USB2_OTG_PD_DR;
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> +
> + udelay(2);
> +
> + tegra186_utmi_bias_pad_power_off(padctl);
> +}
> +
> +static int tegra186_utmi_phy_power_on(struct phy *phy)
> +{
> + struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
> + struct tegra_xusb_usb2_lane *usb2 = to_usb2_lane(lane);
> + struct tegra_xusb_padctl *padctl = lane->pad->padctl;
> + struct tegra186_xusb_padctl *priv = to_tegra186_xusb_padctl(padctl);
> + struct tegra_xusb_usb2_port *port;
> + unsigned int index = lane->index;
> + struct device *dev = padctl->dev;
> + u32 value;
> +
> + port = tegra_xusb_find_usb2_port(padctl, index);
> + if (!port) {
> + dev_err(dev, "no port found for USB2 lane %u\n", index);
> + return -ENODEV;
> + }
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_PAD_MUX);
> + value &= ~(USB2_PORT_MASK << USB2_PORT_SHIFT(index));
> + value |= (PORT_XUSB << USB2_PORT_SHIFT(index));
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_PAD_MUX);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_PORT_CAP);
> + value &= ~(PORT_CAP_MASK << PORTX_CAP_SHIFT(index));
> +
> + if (port->mode == USB_DR_MODE_UNKNOWN)
> + value |= (PORT_CAP_DISABLED << PORTX_CAP_SHIFT(index));
> + else if (port->mode == USB_DR_MODE_PERIPHERAL)
> + value |= (PORT_CAP_DEVICE << PORTX_CAP_SHIFT(index));
> + else if (port->mode == USB_DR_MODE_HOST)
> + value |= (PORT_CAP_HOST << PORTX_CAP_SHIFT(index));
> + else if (port->mode == USB_DR_MODE_OTG)
> + value |= (PORT_CAP_OTG << PORTX_CAP_SHIFT(index));
> +
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_PORT_CAP);
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> + value &= ~USB2_OTG_PD_ZI;
> + value |= TERM_SEL;
> + value &= ~HS_CURR_LEVEL(~0);
> +
> + /* TODO hs_curr_level_offset support */
What is TODO here?
> + if (usb2->hs_curr_level_offset) {
> + int hs_current_level;
> +
> + hs_current_level = (int)priv->calib.hs_curr_level[index] +
> + usb2->hs_curr_level_offset;
> +
> + if (hs_current_level < 0)
> + hs_current_level = 0;
> + if (hs_current_level > 0x3f)
> + hs_current_level = 0x3f;
> +
> + value |= HS_CURR_LEVEL(hs_current_level);
> + } else {
> + value |= HS_CURR_LEVEL(priv->calib.hs_curr_level[index]);
> + }
> +
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL0(index));
> +
> + value = padctl_readl(padctl, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> + value &= ~TERM_RANGE_ADJ(~0);
> + value |= TERM_RANGE_ADJ(priv->calib.hs_term_range_adj);
> + value &= ~RPD_CTRL(~0);
> + value |= RPD_CTRL(priv->calib.rpd_ctrl);
> + padctl_writel(padctl, value, XUSB_PADCTL_USB2_OTG_PADX_CTL1(index));
> +
> + /* TODO: pad power saving */
> + tegra_phy_xusb_utmi_pad_power_on(phy);
> + return 0;
> +}
> +
> +static int tegra186_utmi_phy_power_off(struct phy *phy)
> +{
> + /* TODO: pad power saving */
> + tegra_phy_xusb_utmi_pad_power_down(phy);
> +
> + return 0;
> +}
> +
> +static int tegra186_utmi_phy_init(struct phy *phy)
> +{
> + struct tegra_xusb_lane *lane = phy_get_drvdata(phy);
> + struct tegra_xusb_padctl *padctl = lane->pad->padctl;
> + struct tegra_xusb_usb2_port *port;
> + unsigned int index = lane->index;
> + struct device *dev = padctl->dev;
> + int err;
> +
> + port = tegra_xusb_find_usb2_port(padctl, index);
I would prefer if this entire driver is rewritten without using xusb library.
Ideally you shouldn't have to traverse a list to configure the PHY. phy_get
already does that for you. It should be straight forward to get "port" from
"phy".
I think xusb is making it more complicated than it has to be.
Thanks
Kishon
