On Tue, 2019-02-05 at 16:53 -0800, Eduardo Valentin wrote:
> On Fri, Feb 01, 2019 at 03:38:10PM +0800, michael....@mediatek.com wrote:
> > From: Michael Kao <michael....@mediatek.com>
> >
> > One thermal controller can read four sensors at most,
> > so we need to add controller_offset for the project with
> > more than four sensors to reuse the same register settings.
> >
> > Signed-off-by: Michael Kao <michael....@mediatek.com>
> > ---
> > drivers/thermal/mtk_thermal.c | 79
> > +++++++++++++++++++++++++++++--------------
> > 1 file changed, 54 insertions(+), 25 deletions(-)
> >
> > diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> > index 45c6587..e5cf3f4 100644
> > --- a/drivers/thermal/mtk_thermal.c
> > +++ b/drivers/thermal/mtk_thermal.c
> > @@ -105,6 +105,9 @@
> > /* The number of sensing points per bank */
> > #define MT8173_NUM_SENSORS_PER_ZONE 4
> >
> > +/* The number of controller in the MT8173 */
> > +#define MT8173_NUM_CONTROLLER 1
> > +
> > /* The calibration coefficient of sensor */
> > #define MT8173_CALIBRATION 165
> >
> > @@ -150,6 +153,9 @@ enum {
> > /* The number of sensing points per bank */
> > #define MT2701_NUM_SENSORS_PER_ZONE 3
> >
> > +/* The number of controller in the MT2701 */
> > +#define MT2701_NUM_CONTROLLER 1
> > +
> > /* The calibration coefficient of sensor */
> > #define MT2701_CALIBRATION 165
> >
> > @@ -168,6 +174,9 @@ enum {
> > /* The number of sensing points per bank */
> > #define MT2712_NUM_SENSORS_PER_ZONE 4
> >
> > +/* The number of controller in the MT2712 */
> > +#define MT2712_NUM_CONTROLLER 1
> > +
> > /* The calibration coefficient of sensor */
> > #define MT2712_CALIBRATION 165
> >
> > @@ -176,6 +185,7 @@ enum {
> > #define MT7622_NUM_ZONES 1
> > #define MT7622_NUM_SENSORS_PER_ZONE 1
> > #define MT7622_TS1 0
> > +#define MT7622_NUM_CONTROLLER 1
> >
> > /* The calibration coefficient of sensor */
> > #define MT7622_CALIBRATION 165
> > @@ -201,6 +211,8 @@ struct mtk_thermal_data {
> > const int *msr;
> > const int *adcpnp;
> > const int cali_val;
> > + const int num_controller;
> > + const int *controller_offset;
> > struct thermal_bank_cfg bank_data[];
> > };
> >
> > @@ -240,6 +252,7 @@ struct mtk_thermal {
> > };
> >
> > static const int mt8173_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16
> > };
> > +static const int mt8173_tc_offset[MT8173_NUM_CONTROLLER] = { 0x0, };
> >
> > static const int mt8173_vts_index[MT8173_NUM_SENSORS] = {
> > VTS1, VTS2, VTS3, VTS4, VTSABB
> > @@ -259,6 +272,7 @@ struct mtk_thermal {
> > };
> >
> > static const int mt2701_mux_values[MT2701_NUM_SENSORS] = { 0, 1, 16 };
> > +static const int mt2701_tc_offset[MT2701_NUM_CONTROLLER] = { 0x0, };
> >
> > static const int mt2701_vts_index[MT2701_NUM_SENSORS] = {
> > VTS1, VTS2, VTS3
> > @@ -278,6 +292,7 @@ struct mtk_thermal {
> > };
> >
> > static const int mt2712_mux_values[MT2712_NUM_SENSORS] = { 0, 1, 2, 3 };
> > +static const int mt2712_tc_offset[MT2712_NUM_CONTROLLER] = { 0x0, };
> >
> > static const int mt2712_vts_index[MT2712_NUM_SENSORS] = {
> > VTS1, VTS2, VTS3, VTS4
> > @@ -289,6 +304,7 @@ struct mtk_thermal {
> > static const int mt7622_adcpnp[MT7622_NUM_SENSORS_PER_ZONE] = {
> > TEMP_ADCPNP0, };
> > static const int mt7622_mux_values[MT7622_NUM_SENSORS] = { 0, };
> > static const int mt7622_vts_index[MT7622_NUM_SENSORS] = { VTS1 };
> > +static const int mt7622_tc_offset[MT7622_NUM_CONTROLLER] = { 0x0, };
> >
> > /**
> > * The MT8173 thermal controller has four banks. Each bank can read up to
> > @@ -309,6 +325,8 @@ struct mtk_thermal {
> > .num_sensors = MT8173_NUM_SENSORS,
> > .vts_index = mt8173_vts_index,
> > .cali_val = MT8173_CALIBRATION,
> > + .num_controller = MT8173_NUM_CONTROLLER,
> > + .controller_offset = mt8173_tc_offset,
> > .bank_data = {
> > {
> > .num_sensors = 2,
> > @@ -345,6 +363,8 @@ struct mtk_thermal {
> > .num_sensors = MT2701_NUM_SENSORS,
> > .vts_index = mt2701_vts_index,
> > .cali_val = MT2701_CALIBRATION,
> > + .num_controller = MT2701_NUM_CONTROLLER,
> > + .controller_offset = mt2701_tc_offset,
> > .bank_data = {
> > {
> > .num_sensors = 3,
> > @@ -372,6 +392,8 @@ struct mtk_thermal {
> > .num_sensors = MT2712_NUM_SENSORS,
> > .vts_index = mt2712_vts_index,
> > .cali_val = MT2712_CALIBRATION,
> > + .num_controller = MT2712_NUM_CONTROLLER,
> > + .controller_offset = mt2712_tc_offset,
> > .bank_data = {
> > {
> > .num_sensors = 4,
> > @@ -393,6 +415,8 @@ struct mtk_thermal {
> > .num_sensors = MT7622_NUM_SENSORS,
> > .vts_index = mt7622_vts_index,
> > .cali_val = MT7622_CALIBRATION,
> > + .num_controller = MT7622_NUM_CONTROLLER,
> > + .controller_offset = mt7622_tc_offset,
> > .bank_data = {
> > {
> > .num_sensors = 1,
> > @@ -523,19 +547,23 @@ static int mtk_read_temp(void *data, int *temperature)
> > };
> >
> > static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> > - u32 apmixed_phys_base, u32 auxadc_phys_base)
> > + u32 apmixed_phys_base, u32 auxadc_phys_base,
> > + int ctrl_id)
> > {
> > struct mtk_thermal_bank *bank = &mt->banks[num];
> > const struct mtk_thermal_data *conf = mt->conf;
> > int i;
> >
> > + int offset = mt->conf->controller_offset[ctrl_id];
> > + void *controller_base = mt->thermal_base + offset;
>
> This void * has to be at least __iomem, right?
>
> See the report of kbuild bot, fix it and send it back.
>
OK, I will fix the declaration and send it again.
Thanks!
> > +
> > bank->id = num;
> > bank->mt = mt;
> >
> > mtk_thermal_get_bank(bank);
> >
> > /* bus clock 66M counting unit is 12 * 15.15ns * 256 = 46.540us */
> > - writel(TEMP_MONCTL1_PERIOD_UNIT(12), mt->thermal_base + TEMP_MONCTL1);
> > + writel(TEMP_MONCTL1_PERIOD_UNIT(12), controller_base + TEMP_MONCTL1);
> >
> > /*
> > * filt interval is 1 * 46.540us = 46.54us,
> > @@ -543,21 +571,21 @@ static void mtk_thermal_init_bank(struct mtk_thermal
> > *mt, int num,
> > */
> > writel(TEMP_MONCTL2_FILTER_INTERVAL(1) |
> > TEMP_MONCTL2_SENSOR_INTERVAL(429),
> > - mt->thermal_base + TEMP_MONCTL2);
> > + controller_base + TEMP_MONCTL2);
> >
> > /* poll is set to 10u */
> > writel(TEMP_AHBPOLL_ADC_POLL_INTERVAL(768),
> > - mt->thermal_base + TEMP_AHBPOLL);
> > + controller_base + TEMP_AHBPOLL);
> >
> > /* temperature sampling control, 1 sample */
> > - writel(0x0, mt->thermal_base + TEMP_MSRCTL0);
> > + writel(0x0, controller_base + TEMP_MSRCTL0);
> >
> > /* exceed this polling time, IRQ would be inserted */
> > - writel(0xffffffff, mt->thermal_base + TEMP_AHBTO);
> > + writel(0xffffffff, controller_base + TEMP_AHBTO);
> >
> > /* number of interrupts per event, 1 is enough */
> > - writel(0x0, mt->thermal_base + TEMP_MONIDET0);
> > - writel(0x0, mt->thermal_base + TEMP_MONIDET1);
> > + writel(0x0, controller_base + TEMP_MONIDET0);
> > + writel(0x0, controller_base + TEMP_MONIDET1);
> >
> > /*
> > * The MT8173 thermal controller does not have its own ADC. Instead it
> > @@ -572,44 +600,44 @@ static void mtk_thermal_init_bank(struct mtk_thermal
> > *mt, int num,
> > * this value will be stored to TEMP_PNPMUXADDR (TEMP_SPARE0)
> > * automatically by hw
> > */
> > - writel(BIT(conf->auxadc_channel), mt->thermal_base + TEMP_ADCMUX);
> > + writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCMUX);
> >
> > /* AHB address for auxadc mux selection */
> > writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
> > - mt->thermal_base + TEMP_ADCMUXADDR);
> > + controller_base + TEMP_ADCMUXADDR);
> >
> > /* AHB address for pnp sensor mux selection */
> > writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> > - mt->thermal_base + TEMP_PNPMUXADDR);
> > + controller_base + TEMP_PNPMUXADDR);
> >
> > /* AHB value for auxadc enable */
> > - writel(BIT(conf->auxadc_channel), mt->thermal_base + TEMP_ADCEN);
> > + writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCEN);
> >
> > /* AHB address for auxadc enable (channel 0 immediate mode selected) */
> > writel(auxadc_phys_base + AUXADC_CON1_SET_V,
> > - mt->thermal_base + TEMP_ADCENADDR);
> > + controller_base + TEMP_ADCENADDR);
> >
> > /* AHB address for auxadc valid bit */
> > writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
> > - mt->thermal_base + TEMP_ADCVALIDADDR);
> > + controller_base + TEMP_ADCVALIDADDR);
> >
> > /* AHB address for auxadc voltage output */
> > writel(auxadc_phys_base + AUXADC_DATA(conf->auxadc_channel),
> > - mt->thermal_base + TEMP_ADCVOLTADDR);
> > + controller_base + TEMP_ADCVOLTADDR);
> >
> > /* read valid & voltage are at the same register */
> > - writel(0x0, mt->thermal_base + TEMP_RDCTRL);
> > + writel(0x0, controller_base + TEMP_RDCTRL);
> >
> > /* indicate where the valid bit is */
> > writel(TEMP_ADCVALIDMASK_VALID_HIGH | TEMP_ADCVALIDMASK_VALID_POS(12),
> > - mt->thermal_base + TEMP_ADCVALIDMASK);
> > + controller_base + TEMP_ADCVALIDMASK);
> >
> > /* no shift */
> > - writel(0x0, mt->thermal_base + TEMP_ADCVOLTAGESHIFT);
> > + writel(0x0, controller_base + TEMP_ADCVOLTAGESHIFT);
> >
> > /* enable auxadc mux write transaction */
> > writel(TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
> > - mt->thermal_base + TEMP_ADCWRITECTRL);
> > + controller_base + TEMP_ADCWRITECTRL);
> >
> > for (i = 0; i < conf->bank_data[num].num_sensors; i++)
> > writel(conf->sensor_mux_values[conf->bank_data[num].sensors[i]],
> > @@ -617,11 +645,11 @@ static void mtk_thermal_init_bank(struct mtk_thermal
> > *mt, int num,
> > conf->adcpnp[conf->bank_data[num].sensors[i]]);
> >
> > writel((1 << conf->bank_data[num].num_sensors) - 1,
> > - mt->thermal_base + TEMP_MONCTL0);
> > + controller_base + TEMP_MONCTL0);
> >
> > writel(TEMP_ADCWRITECTRL_ADC_PNP_WRITE |
> > TEMP_ADCWRITECTRL_ADC_MUX_WRITE,
> > - mt->thermal_base + TEMP_ADCWRITECTRL);
> > + controller_base + TEMP_ADCWRITECTRL);
> >
> > mtk_thermal_put_bank(bank);
> > }
> > @@ -737,7 +765,7 @@ static int mtk_thermal_get_calibration_data(struct
> > device *dev,
> >
> > static int mtk_thermal_probe(struct platform_device *pdev)
> > {
> > - int ret, i;
> > + int ret, i, ctrl_id;
> > struct device_node *auxadc, *apmixedsys, *np = pdev->dev.of_node;
> > struct mtk_thermal *mt;
> > struct resource *res;
> > @@ -817,9 +845,10 @@ static int mtk_thermal_probe(struct platform_device
> > *pdev)
> > goto err_disable_clk_auxadc;
> > }
> >
> > - for (i = 0; i < mt->conf->num_banks; i++)
> > - mtk_thermal_init_bank(mt, i, apmixed_phys_base,
> > - auxadc_phys_base);
> > + for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
> > + for (i = 0; i < mt->conf->num_banks; i++)
> > + mtk_thermal_init_bank(mt, i, apmixed_phys_base,
> > + auxadc_phys_base, ctrl_id);
> >
> > platform_set_drvdata(pdev, mt);
> >
> > --
> > 1.9.1
> >
