On Tue, Feb 12, 2019 at 04:14:09PM +0100, Neil Armstrong wrote:
> Adds the bindings for the Amlogic G12A USB Glue HW.
>
> The Amlogic G12A SoC Family embeds 2 USB Controllers :
> - a DWC3 IP configured as Host for USB2 and USB3
> - a DWC2 IP configured as Peripheral USB2 Only
>
> A glue connects these both controllers to 2 USB2 PHYs,
> and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.
>
> The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
> routing of the OTG PHY between the DWC3 and DWC2 controllers, and
> setups the on-chip OTG mode selection for this PHY.
>
> The PHYs are children of the Glue node since the Glue controls the interface
> with the PHY, not the DWC3 controller.
>
> The PHY interconnect is handled into ports subnodes, which eases describing
> which PHY is enabled (like the USB3 shared PHY) and futures layouts on
> derivatives of the G12A Family.
>
> Signed-off-by: Neil Armstrong <[email protected]>
> ---
> .../devicetree/bindings/usb/amlogic,dwc3.txt | 109 ++++++++++++++++++
> 1 file changed, 109 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
> b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
> index 9a8b631904fd..c7c4726ef10d 100644
> --- a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt
> @@ -40,3 +40,112 @@ Example device nodes:
> phy-names = "usb2-phy", "usb3-phy";
> };
> };
> +
> +Amlogic Meson G12A DWC3 USB SoC Controller Glue
> +
> +The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
> +in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
> +only.
> +
> +A glue connects the DWC3 core to USB2 PHYs and optionnaly to an USB3 PHY.
> +
> +One of the USB2 PHY can be re-routed in peripheral mode to a DWC2 USB IP.
> +
> +The DWC3 Glue controls the PHY routing and power, an interrupt line is
> +connected to the Glue to serve as OTG ID change detection.
> +
> +Required properties:
> +- compatible: Should be "amlogic,meson-g12a-usb-ctrl"
> +- clocks: a handle for the "USB" clock
> +- clock-names: must be "usb"
> +- resets: a handle for the shared "USB" reset line
> +- reset-names: must be "usb"
-name for a single entry is pointless.
> +- reg: The base address and length of the registers
> +- interrupts: the interrupt specifier for the OTG detection
> +
> +Required child nodes:
> +
> +USB Ports are described as child 'port' nodes grouped under a 'ports' node,
> +with #address-cells, #size-cells specified.
> +
> +Each 'port' sub-node identifies a possible USB Port served by an USB PHY
> +identified by the 'phy' property as decribed in ../phy/phy-bindings.txt
> +
> +Each 'port' is identified by a reg property to number the port.
> +
> +The following table lists for each supported model the port number
> +corresponding to each PHY serving a physical USB Port.
> +
> + Family Port 0 Port 1 Port 2 Port 3 Port 4
> +---------------------------------------------------------------
> + G12A USBHOST_A USBOTG_B Reserved Reserved USB3_0
> +
> +A child node must exist to represent the core DWC3 IP block. The name of
> +the node is not important. The content of the node is defined in dwc3.txt.
> +
> +A child node must exist to represent the core DWC2 IP block. The name of
> +the node is not important. The content of the node is defined in dwc2.txt.
> +
> +PHY documentation is provided in the following places:
> +- Documentation/devicetree/bindings/phy/meson-g12a-usb2-phy.txt
> +- Documentation/devicetree/bindings/phy/meson-g12a-usb3-pcie-phy.txt
> +
> +
> +Example device nodes:
> + usb: usb@ffe09000 {
> + compatible = "amlogic,meson-g12a-usb-ctrl";
> + reg = <0x0 0xffe09000 0x0 0xa0>;
> + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&clkc CLKID_USB>;
> + clock-names = "usb";
> + resets = <&reset RESET_USB>;
> + reset-names = "usb";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + /* USB2 Port 0 */
> + usb20: port@0 {
> + reg = <0>;
> + phys = <&usb2_phy0>;
'ports' and 'port' are reserved for the graph binding. Don't use it for
your own thing.
Can't you just make 'phys' a list using 0 phandle if you need to skip
entries.
> + };
> +
> + /* USB2 Port 1 */
> + usb21: port@1 {
> + reg = <1>;
> + phys = <&usb2_phy1>;
> + };
> +
> + /* USB3 Port 0 */
> + usb3: port@4 {
> + reg = <4>;
> + phys = <&usb3_pcie_phy PHY_TYPE_USB3>;
> + };
> + };
> +
> + dwc2: usb@ff400000 {
> + compatible = "amlogic,meson-g12a-usb",
> "snps,dwc2";
> + reg = <0x0 0xff400000 0x0 0x40000>;
> + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
> + clock-names = "ddr";
> + dr_mode = "peripheral";
> + g-rx-fifo-size = <192>;
> + g-np-tx-fifo-size = <128>;
> + g-tx-fifo-size = <128 128 16 16 16>;
> + };
> +
> + dwc3: dwc3@ff500000 {
usb@... or usb3@...
> + compatible = "snps,dwc3";
> + reg = <0x0 0xff500000 0x0 0x100000>;
> + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
> + dr_mode = "host";
> + snps,dis_u2_susphy_quirk;
> + snps,quirk-frame-length-adjustment;
> + };
> + };
> --
> 2.20.1
>
