Formatting of Kconfig files doesn't look so pretty, so let the Great White Handkerchief come around and clean it up.
Signed-off-by: Enrico Weigelt, metux IT consult <i...@metux.net> --- drivers/soc/fsl/Kconfig | 9 +++++---- drivers/soc/qcom/Kconfig | 23 ++++++++++++----------- drivers/soc/rockchip/Kconfig | 18 +++++++++--------- 3 files changed, 26 insertions(+), 24 deletions(-) diff --git a/drivers/soc/fsl/Kconfig b/drivers/soc/fsl/Kconfig index 61f8e14..0db980a 100644 --- a/drivers/soc/fsl/Kconfig +++ b/drivers/soc/fsl/Kconfig @@ -20,13 +20,14 @@ config FSL_GUTS into this driver as well. config FSL_MC_DPIO - tristate "QorIQ DPAA2 DPIO driver" - depends on FSL_MC_BUS - select SOC_BUS - help + tristate "QorIQ DPAA2 DPIO driver" + depends on FSL_MC_BUS + select SOC_BUS + help Driver for the DPAA2 DPIO object. A DPIO provides queue and buffer management facilities for software to interact with other DPAA2 objects. This driver does not expose the DPIO objects individually, but groups them under a service layer API. + endmenu diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig index 1ee298f..e885233 100644 --- a/drivers/soc/qcom/Kconfig +++ b/drivers/soc/qcom/Kconfig @@ -32,13 +32,13 @@ config QCOM_GLINK_SSR neighboring subsystems going up or down. config QCOM_GSBI - tristate "QCOM General Serial Bus Interface" - depends on ARCH_QCOM || COMPILE_TEST - select MFD_SYSCON - help - Say y here to enable GSBI support. The GSBI provides control - functions for connecting the underlying serial UART, SPI, and I2C - devices to the output pins. + tristate "QCOM General Serial Bus Interface" + depends on ARCH_QCOM || COMPILE_TEST + select MFD_SYSCON + help + Say y here to enable GSBI support. The GSBI provides control + functions for connecting the underlying serial UART, SPI, and I2C + devices to the output pins. config QCOM_LLCC tristate "Qualcomm Technologies, Inc. LLCC driver" @@ -175,8 +175,9 @@ config QCOM_APR depends on ARCH_QCOM || COMPILE_TEST depends on RPMSG help - Enable APR IPC protocol support between - application processor and QDSP6. APR is - used by audio driver to configure QDSP6 - ASM, ADM and AFE modules. + Enable APR IPC protocol support between + application processor and QDSP6. APR is + used by audio driver to configure QDSP6 + ASM, ADM and AFE modules. + endmenu diff --git a/drivers/soc/rockchip/Kconfig b/drivers/soc/rockchip/Kconfig index 20da55d..f468b79 100644 --- a/drivers/soc/rockchip/Kconfig +++ b/drivers/soc/rockchip/Kconfig @@ -14,15 +14,15 @@ config ROCKCHIP_GRF to make some of them conform to expectations of the kernel. config ROCKCHIP_PM_DOMAINS - bool "Rockchip generic power domain" - depends on PM - select PM_GENERIC_DOMAINS - help - Say y here to enable power domain support. - In order to meet high performance and low power requirements, a power - management unit is designed or saving power when RK3288 in low power - mode. The RK3288 PMU is dedicated for managing the power of the whole chip. + bool "Rockchip generic power domain" + depends on PM + select PM_GENERIC_DOMAINS + help + Say y here to enable power domain support. + In order to meet high performance and low power requirements, a power + management unit is designed or saving power when RK3288 in low power + mode. The RK3288 PMU is dedicated for managing the power of the whole chip. - If unsure, say N. + If unsure, say N. endif -- 1.9.1