The ingenic-nand driver uses an API provided by the jz4780-bch driver.
This makes it difficult to support other SoCs in the jz4780-bch driver.
To work around this, we separate the API functions from the SoC-specific
code, so that these API functions are SoC-agnostic.
Signed-off-by: Paul Cercueil <p...@crapouillou.net>
---
Notes:
v2: Add an optional .probe() callback. It is used for instance to set
the clock rate in the JZ4780 backend.
v3: The common code is now inside the ingenic-ecc module. Each
SoC-specific ECC code is now in its own module, which leaves to the
user the choice of which (if any) ECC code should be supported.
v4: No change
v5: Remove .probe callback. Instead, call ingenic_ecc_probe from
jz4780_bch_probe and set the clock rate afterwards.
drivers/mtd/nand/raw/ingenic/Kconfig | 17 +++
drivers/mtd/nand/raw/ingenic/Makefile | 5 +-
drivers/mtd/nand/raw/ingenic/ingenic_ecc.c | 153 +++++++++++++++++++++++++
drivers/mtd/nand/raw/ingenic/ingenic_ecc.h | 83 ++++++++++++++
drivers/mtd/nand/raw/ingenic/ingenic_nand.c | 40 +++----
drivers/mtd/nand/raw/ingenic/jz4780_bch.c | 172 +++++-----------------------
drivers/mtd/nand/raw/ingenic/jz4780_bch.h | 40 -------
7 files changed, 307 insertions(+), 203 deletions(-)
create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
create mode 100644 drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
delete mode 100644 drivers/mtd/nand/raw/ingenic/jz4780_bch.h
diff --git a/drivers/mtd/nand/raw/ingenic/Kconfig
b/drivers/mtd/nand/raw/ingenic/Kconfig
index 67806c87b2c4..4bf7d7af3b0a 100644
--- a/drivers/mtd/nand/raw/ingenic/Kconfig
+++ b/drivers/mtd/nand/raw/ingenic/Kconfig
@@ -11,3 +11,20 @@ config MTD_NAND_JZ4780
help
Enables support for NAND Flash connected to the NEMC on JZ4780 SoC
based boards, using the BCH controller for hardware error correction.
+
+if MTD_NAND_JZ4780
+
+config MTD_NAND_INGENIC_ECC
+ tristate
+
+config MTD_NAND_JZ4780_BCH
+ tristate "Hardware BCH support for JZ4780 SoC"
+ select MTD_NAND_INGENIC_ECC
+ help
+ Enable this driver to support the BCH error-correction hardware
+ present on the JZ4780 SoC from Ingenic.
+
+ This driver can also be built as a module. If so, the module
+ will be called jz4780-bch.
+
+endif # MTD_NAND_JZ4780
diff --git a/drivers/mtd/nand/raw/ingenic/Makefile
b/drivers/mtd/nand/raw/ingenic/Makefile
index af2d5de21f60..f3c3c0f230b0 100644
--- a/drivers/mtd/nand/raw/ingenic/Makefile
+++ b/drivers/mtd/nand/raw/ingenic/Makefile
@@ -1,2 +1,5 @@
obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o
-obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o jz4780_bch.o
+obj-$(CONFIG_MTD_NAND_JZ4780) += ingenic_nand.o
+
+obj-$(CONFIG_MTD_NAND_INGENIC_ECC) += ingenic_ecc.o
+obj-$(CONFIG_MTD_NAND_JZ4780_BCH) += jz4780_bch.o
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
new file mode 100644
index 000000000000..d7f3a8c3abea
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.c
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * JZ47xx ECC common code
+ *
+ * Copyright (c) 2015 Imagination Technologies
+ * Author: Alex Smith <alex.sm...@imgtec.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/init.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include "ingenic_ecc.h"
+
+/**
+ * ingenic_ecc_calculate() - calculate ECC for a data buffer
+ * @ecc: ECC device.
+ * @params: ECC parameters.
+ * @buf: input buffer with raw data.
+ * @ecc_code: output buffer with ECC.
+ *
+ * Return: 0 on success, -ETIMEDOUT if timed out while waiting for ECC
+ * controller.
+ */
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ const u8 *buf, u8 *ecc_code)
+{
+ return ecc->ops->calculate(ecc, params, buf, ecc_code);
+}
+EXPORT_SYMBOL(ingenic_ecc_calculate);
+
+/**
+ * ingenic_ecc_correct() - detect and correct bit errors
+ * @ecc: ECC device.
+ * @params: ECC parameters.
+ * @buf: raw data read from the chip.
+ * @ecc_code: ECC read from the chip.
+ *
+ * Given the raw data and the ECC read from the NAND device, detects and
+ * corrects errors in the data.
+ *
+ * Return: the number of bit errors corrected, -EBADMSG if there are too many
+ * errors to correct or -ETIMEDOUT if we timed out waiting for the controller.
+ */
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ u8 *buf, u8 *ecc_code)
+{
+ return ecc->ops->correct(ecc, params, buf, ecc_code);
+}
+EXPORT_SYMBOL(ingenic_ecc_correct);
+
+/**
+ * ingenic_ecc_get() - get the ECC controller device
+ * @np: ECC device tree node.
+ *
+ * Gets the ECC controller device from the specified device tree node. The
+ * device must be released with ingenic_ecc_release() when it is no longer
being
+ * used.
+ *
+ * Return: a pointer to ingenic_ecc, errors are encoded into the pointer.
+ * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
+ */
+static struct ingenic_ecc *ingenic_ecc_get(struct device_node *np)
+{
+ struct platform_device *pdev;
+ struct ingenic_ecc *ecc;
+
+ pdev = of_find_device_by_node(np);
+ if (!pdev || !platform_get_drvdata(pdev))
+ return ERR_PTR(-EPROBE_DEFER);
+
+ get_device(&pdev->dev);
+
+ ecc = platform_get_drvdata(pdev);
+ clk_prepare_enable(ecc->clk);
+
+ return ecc;
+}
+
+/**
+ * of_ingenic_ecc_get() - get the ECC controller from a DT node
+ * @of_node: the node that contains a bch-controller property.
+ *
+ * Get the bch-controller property from the given device tree
+ * node and pass it to ingenic_ecc_get to do the work.
+ *
+ * Return: a pointer to ingenic_ecc, errors are encoded into the pointer.
+ * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
+ */
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *of_node)
+{
+ struct ingenic_ecc *ecc = NULL;
+ struct device_node *np;
+
+ np = of_parse_phandle(of_node, "ingenic,bch-controller", 0);
+
+ if (np) {
+ ecc = ingenic_ecc_get(np);
+ of_node_put(np);
+ }
+ return ecc;
+}
+EXPORT_SYMBOL(of_ingenic_ecc_get);
+
+/**
+ * ingenic_ecc_release() - release the ECC controller device
+ * @ecc: ECC device.
+ */
+void ingenic_ecc_release(struct ingenic_ecc *ecc)
+{
+ clk_disable_unprepare(ecc->clk);
+ put_device(ecc->dev);
+}
+EXPORT_SYMBOL(ingenic_ecc_release);
+
+int ingenic_ecc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ingenic_ecc *ecc;
+ struct resource *res;
+
+ ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL);
+ if (!ecc)
+ return -ENOMEM;
+
+ ecc->ops = device_get_match_data(dev);
+ if (!ecc->ops)
+ return -EINVAL;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ecc->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ecc->base))
+ return PTR_ERR(ecc->base);
+
+ ecc->ops->disable(ecc);
+
+ ecc->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(ecc->clk)) {
+ dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(ecc->clk));
+ return PTR_ERR(ecc->clk);
+ }
+
+ mutex_init(&ecc->lock);
+
+ ecc->dev = dev;
+ platform_set_drvdata(pdev, ecc);
+
+ return 0;
+}
+EXPORT_SYMBOL(ingenic_ecc_probe);
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
new file mode 100644
index 000000000000..d0486f963cc9
--- /dev/null
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_ecc.h
@@ -0,0 +1,83 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__
+#define __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__
+
+#include <linux/compiler_types.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/types.h>
+#include <uapi/asm-generic/errno-base.h>
+
+struct clk;
+struct device;
+struct ingenic_ecc;
+struct platform_device;
+
+/**
+ * struct ingenic_ecc_params - ECC parameters
+ * @size: data bytes per ECC step.
+ * @bytes: ECC bytes per step.
+ * @strength: number of correctable bits per ECC step.
+ */
+struct ingenic_ecc_params {
+ int size;
+ int bytes;
+ int strength;
+};
+
+#ifdef CONFIG_MTD_NAND_INGENIC_ECC
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ const u8 *buf, u8 *ecc_code);
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params, u8 *buf,
+ u8 *ecc_code);
+
+void ingenic_ecc_release(struct ingenic_ecc *ecc);
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np);
+#else /* CONFIG_MTD_NAND_INGENIC_ECC */
+int ingenic_ecc_calculate(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ const u8 *buf, u8 *ecc_code)
+{
+ return -ENODEV;
+}
+
+int ingenic_ecc_correct(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params, u8 *buf,
+ u8 *ecc_code)
+{
+ return -ENODEV;
+}
+
+void ingenic_ecc_release(struct ingenic_ecc *ecc)
+{
+}
+
+struct ingenic_ecc *of_ingenic_ecc_get(struct device_node *np)
+{
+ return ERR_PTR(-ENODEV);
+}
+#endif /* CONFIG_MTD_NAND_INGENIC_ECC */
+
+struct ingenic_ecc_ops {
+ void (*disable)(struct ingenic_ecc *ecc);
+ int (*calculate)(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ const u8 *buf, u8 *ecc_code);
+ int (*correct)(struct ingenic_ecc *ecc,
+ struct ingenic_ecc_params *params,
+ u8 *buf, u8 *ecc_code);
+};
+
+struct ingenic_ecc {
+ struct device *dev;
+ const struct ingenic_ecc_ops *ops;
+ void __iomem *base;
+ struct clk *clk;
+ struct mutex lock;
+};
+
+int ingenic_ecc_probe(struct platform_device *pdev);
+
+#endif /* __DRIVERS_MTD_NAND_INGENIC_ECC_INTERNAL_H__ */
diff --git a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
index 8c73f7c5be9a..a5f2f21c5198 100644
--- a/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
+++ b/drivers/mtd/nand/raw/ingenic/ingenic_nand.c
@@ -22,7 +22,7 @@
#include <linux/jz4780-nemc.h>
-#include "jz4780_bch.h"
+#include "ingenic_ecc.h"
#define DRV_NAME "ingenic-nand"
@@ -40,7 +40,7 @@ struct ingenic_nand_cs {
struct ingenic_nfc {
struct device *dev;
- struct jz4780_bch *bch;
+ struct ingenic_ecc *ecc;
struct nand_controller controller;
unsigned int num_banks;
struct list_head chips;
@@ -124,11 +124,11 @@ static int ingenic_nand_ecc_calculate(struct nand_chip
*chip, const u8 *dat,
{
struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
- struct jz4780_bch_params params;
+ struct ingenic_ecc_params params;
/*
- * Don't need to generate the ECC when reading, BCH does it for us as
- * part of decoding/correction.
+ * Don't need to generate the ECC when reading, the ECC engine does it
+ * for us as part of decoding/correction.
*/
if (nand->reading)
return 0;
@@ -137,7 +137,7 @@ static int ingenic_nand_ecc_calculate(struct nand_chip
*chip, const u8 *dat,
params.bytes = nand->chip.ecc.bytes;
params.strength = nand->chip.ecc.strength;
- return jz4780_bch_calculate(nfc->bch, ¶ms, dat, ecc_code);
+ return ingenic_ecc_calculate(nfc->ecc, ¶ms, dat, ecc_code);
}
static int ingenic_nand_ecc_correct(struct nand_chip *chip, u8 *dat,
@@ -145,13 +145,13 @@ static int ingenic_nand_ecc_correct(struct nand_chip
*chip, u8 *dat,
{
struct ingenic_nand *nand = to_ingenic_nand(nand_to_mtd(chip));
struct ingenic_nfc *nfc = to_ingenic_nfc(nand->chip.controller);
- struct jz4780_bch_params params;
+ struct ingenic_ecc_params params;
params.size = nand->chip.ecc.size;
params.bytes = nand->chip.ecc.bytes;
params.strength = nand->chip.ecc.strength;
- return jz4780_bch_correct(nfc->bch, ¶ms, dat, read_ecc);
+ return ingenic_ecc_correct(nfc->ecc, ¶ms, dat, read_ecc);
}
static int ingenic_nand_attach_chip(struct nand_chip *chip)
@@ -165,8 +165,8 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
switch (chip->ecc.mode) {
case NAND_ECC_HW:
- if (!nfc->bch) {
- dev_err(nfc->dev, "HW BCH selected, but BCH controller
not found\n");
+ if (!nfc->ecc) {
+ dev_err(nfc->dev, "HW ECC selected, but ECC controller
not found\n");
return -ENODEV;
}
@@ -176,7 +176,7 @@ static int ingenic_nand_attach_chip(struct nand_chip *chip)
/* fall through */
case NAND_ECC_SOFT:
dev_info(nfc->dev, "using %s (strength %d, size %d, bytes
%d)\n",
- (nfc->bch) ? "hardware BCH" : "software ECC",
+ (nfc->ecc) ? "hardware ECC" : "software ECC",
chip->ecc.strength, chip->ecc.size, chip->ecc.bytes);
break;
case NAND_ECC_NONE:
@@ -354,12 +354,12 @@ static int ingenic_nand_probe(struct platform_device
*pdev)
return -ENOMEM;
/*
- * Check for BCH HW before we call nand_scan_ident, to prevent us from
- * having to call it again if the BCH driver returns -EPROBE_DEFER.
+ * Check for ECC HW before we call nand_scan_ident, to prevent us from
+ * having to call it again if the ECC driver returns -EPROBE_DEFER.
*/
- nfc->bch = of_jz4780_bch_get(dev->of_node);
- if (IS_ERR(nfc->bch))
- return PTR_ERR(nfc->bch);
+ nfc->ecc = of_ingenic_ecc_get(dev->of_node);
+ if (IS_ERR(nfc->ecc))
+ return PTR_ERR(nfc->ecc);
nfc->dev = dev;
nfc->num_banks = num_banks;
@@ -369,8 +369,8 @@ static int ingenic_nand_probe(struct platform_device *pdev)
ret = ingenic_nand_init_chips(nfc, pdev);
if (ret) {
- if (nfc->bch)
- jz4780_bch_release(nfc->bch);
+ if (nfc->ecc)
+ ingenic_ecc_release(nfc->ecc);
return ret;
}
@@ -382,8 +382,8 @@ static int ingenic_nand_remove(struct platform_device *pdev)
{
struct ingenic_nfc *nfc = platform_get_drvdata(pdev);
- if (nfc->bch)
- jz4780_bch_release(nfc->bch);
+ if (nfc->ecc)
+ ingenic_ecc_release(nfc->ecc);
ingenic_nand_cleanup_chips(nfc);
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
index 7635753bd7ea..079266a0d6cf 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
+++ b/drivers/mtd/nand/raw/ingenic/jz4780_bch.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * JZ4780 BCH controller
+ * JZ4780 BCH controller driver
*
* Copyright (c) 2015 Imagination Technologies
* Author: Alex Smith <alex.sm...@imgtec.com>
@@ -8,18 +8,15 @@
#include <linux/bitops.h>
#include <linux/clk.h>
-#include <linux/delay.h>
-#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/io.h>
#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/mutex.h>
-#include <linux/of.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include "jz4780_bch.h"
+#include "ingenic_ecc.h"
#define BCH_BHCR 0x0
#define BCH_BHCCR 0x8
@@ -62,15 +59,8 @@
/* Timeout for BCH calculation/correction. */
#define BCH_TIMEOUT_US 100000
-struct jz4780_bch {
- struct device *dev;
- void __iomem *base;
- struct clk *clk;
- struct mutex lock;
-};
-
-static void jz4780_bch_reset(struct jz4780_bch *bch,
- struct jz4780_bch_params *params, bool encode)
+static void jz4780_bch_reset(struct ingenic_ecc *bch,
+ struct ingenic_ecc_params *params, bool encode)
{
u32 reg;
@@ -90,13 +80,13 @@ static void jz4780_bch_reset(struct jz4780_bch *bch,
writel(reg, bch->base + BCH_BHCR);
}
-static void jz4780_bch_disable(struct jz4780_bch *bch)
+static void jz4780_bch_disable(struct ingenic_ecc *bch)
{
writel(readl(bch->base + BCH_BHINT), bch->base + BCH_BHINT);
writel(BCH_BHCR_BCHE, bch->base + BCH_BHCCR);
}
-static void jz4780_bch_write_data(struct jz4780_bch *bch, const void *buf,
+static void jz4780_bch_write_data(struct ingenic_ecc *bch, const void *buf,
size_t size)
{
size_t size32 = size / sizeof(u32);
@@ -113,7 +103,7 @@ static void jz4780_bch_write_data(struct jz4780_bch *bch,
const void *buf,
writeb(*src8++, bch->base + BCH_BHDR);
}
-static void jz4780_bch_read_parity(struct jz4780_bch *bch, void *buf,
+static void jz4780_bch_read_parity(struct ingenic_ecc *bch, void *buf,
size_t size)
{
size_t size32 = size / sizeof(u32);
@@ -143,7 +133,7 @@ static void jz4780_bch_read_parity(struct jz4780_bch *bch,
void *buf,
}
}
-static bool jz4780_bch_wait_complete(struct jz4780_bch *bch, unsigned int irq,
+static bool jz4780_bch_wait_complete(struct ingenic_ecc *bch, unsigned int irq,
u32 *status)
{
u32 reg;
@@ -167,18 +157,9 @@ static bool jz4780_bch_wait_complete(struct jz4780_bch
*bch, unsigned int irq,
return true;
}
-/**
- * jz4780_bch_calculate() - calculate ECC for a data buffer
- * @bch: BCH device.
- * @params: BCH parameters.
- * @buf: input buffer with raw data.
- * @ecc_code: output buffer with ECC.
- *
- * Return: 0 on success, -ETIMEDOUT if timed out while waiting for BCH
- * controller.
- */
-int jz4780_bch_calculate(struct jz4780_bch *bch, struct jz4780_bch_params
*params,
- const u8 *buf, u8 *ecc_code)
+static int jz4780_calculate(struct ingenic_ecc *bch,
+ struct ingenic_ecc_params *params,
+ const u8 *buf, u8 *ecc_code)
{
int ret = 0;
@@ -198,23 +179,10 @@ int jz4780_bch_calculate(struct jz4780_bch *bch, struct
jz4780_bch_params *param
mutex_unlock(&bch->lock);
return ret;
}
-EXPORT_SYMBOL(jz4780_bch_calculate);
-
-/**
- * jz4780_bch_correct() - detect and correct bit errors
- * @bch: BCH device.
- * @params: BCH parameters.
- * @buf: raw data read from the chip.
- * @ecc_code: ECC read from the chip.
- *
- * Given the raw data and the ECC read from the NAND device, detects and
- * corrects errors in the data.
- *
- * Return: the number of bit errors corrected, -EBADMSG if there are too many
- * errors to correct or -ETIMEDOUT if we timed out waiting for the controller.
- */
-int jz4780_bch_correct(struct jz4780_bch *bch, struct jz4780_bch_params
*params,
- u8 *buf, u8 *ecc_code)
+
+static int jz4780_correct(struct ingenic_ecc *bch,
+ struct ingenic_ecc_params *params,
+ u8 *buf, u8 *ecc_code)
{
u32 reg, mask, index;
int i, ret, count;
@@ -260,110 +228,30 @@ int jz4780_bch_correct(struct jz4780_bch *bch, struct
jz4780_bch_params *params,
mutex_unlock(&bch->lock);
return ret;
}
-EXPORT_SYMBOL(jz4780_bch_correct);
-
-/**
- * jz4780_bch_get() - get the BCH controller device
- * @np: BCH device tree node.
- *
- * Gets the BCH controller device from the specified device tree node. The
- * device must be released with jz4780_bch_release() when it is no longer being
- * used.
- *
- * Return: a pointer to jz4780_bch, errors are encoded into the pointer.
- * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
- */
-static struct jz4780_bch *jz4780_bch_get(struct device_node *np)
-{
- struct platform_device *pdev;
- struct jz4780_bch *bch;
-
- pdev = of_find_device_by_node(np);
- if (!pdev)
- return ERR_PTR(-EPROBE_DEFER);
-
- bch = platform_get_drvdata(pdev);
- if (!bch) {
- put_device(&pdev->dev);
- return ERR_PTR(-EPROBE_DEFER);
- }
-
- clk_prepare_enable(bch->clk);
-
- return bch;
-}
-
-/**
- * of_jz4780_bch_get() - get the BCH controller from a DT node
- * @of_node: the node that contains a bch-controller property.
- *
- * Get the bch-controller property from the given device tree
- * node and pass it to jz4780_bch_get to do the work.
- *
- * Return: a pointer to jz4780_bch, errors are encoded into the pointer.
- * PTR_ERR(-EPROBE_DEFER) if the device hasn't been initialised yet.
- */
-struct jz4780_bch *of_jz4780_bch_get(struct device_node *of_node)
-{
- struct jz4780_bch *bch = NULL;
- struct device_node *np;
-
- np = of_parse_phandle(of_node, "ingenic,bch-controller", 0);
-
- if (np) {
- bch = jz4780_bch_get(np);
- of_node_put(np);
- }
- return bch;
-}
-EXPORT_SYMBOL(of_jz4780_bch_get);
-
-/**
- * jz4780_bch_release() - release the BCH controller device
- * @bch: BCH device.
- */
-void jz4780_bch_release(struct jz4780_bch *bch)
-{
- clk_disable_unprepare(bch->clk);
- put_device(bch->dev);
-}
-EXPORT_SYMBOL(jz4780_bch_release);
static int jz4780_bch_probe(struct platform_device *pdev)
{
- struct device *dev = &pdev->dev;
- struct jz4780_bch *bch;
- struct resource *res;
-
- bch = devm_kzalloc(dev, sizeof(*bch), GFP_KERNEL);
- if (!bch)
- return -ENOMEM;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- bch->base = devm_ioremap_resource(dev, res);
- if (IS_ERR(bch->base))
- return PTR_ERR(bch->base);
-
- jz4780_bch_disable(bch);
+ struct ingenic_ecc *bch;
+ int ret;
- bch->clk = devm_clk_get(dev, NULL);
- if (IS_ERR(bch->clk)) {
- dev_err(dev, "failed to get clock: %ld\n", PTR_ERR(bch->clk));
- return PTR_ERR(bch->clk);
- }
+ ret = ingenic_ecc_probe(pdev);
+ if (ret)
+ return ret;
+ bch = platform_get_drvdata(pdev);
clk_set_rate(bch->clk, BCH_CLK_RATE);
- mutex_init(&bch->lock);
-
- bch->dev = dev;
- platform_set_drvdata(pdev, bch);
-
return 0;
}
+static const struct ingenic_ecc_ops jz4780_bch_ops = {
+ .disable = jz4780_bch_disable,
+ .calculate = jz4780_calculate,
+ .correct = jz4780_correct,
+};
+
static const struct of_device_id jz4780_bch_dt_match[] = {
- { .compatible = "ingenic,jz4780-bch" },
+ { .compatible = "ingenic,jz4780-bch", .data = &jz4780_bch_ops },
{},
};
MODULE_DEVICE_TABLE(of, jz4780_bch_dt_match);
diff --git a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
b/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
deleted file mode 100644
index 451e0c770160..000000000000
--- a/drivers/mtd/nand/raw/ingenic/jz4780_bch.h
+++ /dev/null
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * JZ4780 BCH controller
- *
- * Copyright (c) 2015 Imagination Technologies
- * Author: Alex Smith <alex.sm...@imgtec.com>
- */
-
-#ifndef __DRIVERS_MTD_NAND_JZ4780_BCH_H__
-#define __DRIVERS_MTD_NAND_JZ4780_BCH_H__
-
-#include <linux/types.h>
-
-struct device;
-struct device_node;
-struct jz4780_bch;
-
-/**
- * struct jz4780_bch_params - BCH parameters
- * @size: data bytes per ECC step.
- * @bytes: ECC bytes per step.
- * @strength: number of correctable bits per ECC step.
- */
-struct jz4780_bch_params {
- int size;
- int bytes;
- int strength;
-};
-
-int jz4780_bch_calculate(struct jz4780_bch *bch,
- struct jz4780_bch_params *params,
- const u8 *buf, u8 *ecc_code);
-int jz4780_bch_correct(struct jz4780_bch *bch,
- struct jz4780_bch_params *params, u8 *buf,
- u8 *ecc_code);
-
-void jz4780_bch_release(struct jz4780_bch *bch);
-struct jz4780_bch *of_jz4780_bch_get(struct device_node *np);
-
-#endif /* __DRIVERS_MTD_NAND_JZ4780_BCH_H__ */
--
2.11.0
