Adds the devicetree bindings for the si5341 driver that supports the Si5341 and Si5340 chips.
Signed-off-by: Mike Looijmans <mike.looijm...@topic.nl> --- .../bindings/clock/silabs,si5341.txt | 141 ++++++++++++++++++ 1 file changed, 141 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/silabs,si5341.txt diff --git a/Documentation/devicetree/bindings/clock/silabs,si5341.txt b/Documentation/devicetree/bindings/clock/silabs,si5341.txt new file mode 100644 index 000000000000..1a00dd83100f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si5341.txt @@ -0,0 +1,141 @@ +Binding for Silicon Labs Si5341 and Si5340 programmable i2c clock generator. + +Reference +[1] Si5341 Data Sheet + https://www.silabs.com/documents/public/reference-manuals/Si5341-40-D-RM.pdf + +The Si5341 and Si5340 are programmable i2c clock generators with up to 10 output +clocks. The chip contains a PLL that sources 5 (or 4) multisynth clocks, which +in turn can be directed to any of the 10 (or 4) outputs through a divider. +The internal structure of the clock generators can be found in [1]. + +The driver can be used in "as is" mode, reading the current settings from the +chip at boot, in case you have a (pre-)programmed device. If the PLL is not +configured when the driver probes, it assumes the driver must fully initialize +it. + +The device type, speed grade and revision are determined runtime by probing. + +The driver currently only supports XTAL input mode, and does not support any +fancy input configurations. They can still be programmed into the chip and +the driver will leave them "as is". + +==I2C device node== + +Required properties: +- compatible: shall be one of the following: "silabs,si5341", "silabs,si5340" +- reg: i2c device address, usually 0x74 +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock + handles, shall be xtal reference clock. Usually a fixed clock. +- clock-names: Shall be "xtal". +- #address-cells: shall be set to 1. +- #size-cells: shall be set to 0. + +Optional properties: +- silabs,pll-m-num, silabs,pll-m-den: Numerator and denominator for PLL + feedback divider. Must be such that the PLL output is in the valid range. For + example, to create 14GHz from a 48MHz xtal, use m-num=14000 and m-den=48. Only + the fraction matters, using 3500 and 12 will deliver the exact same result. + If these are not specified, and the PLL is not yet programmed when the driver + probes, the PLL will be set to 14GHz. +- silabs,reprogram: When present, the driver will always assume the device must + be initialized, and always performs the soft-reset routine. Since this will + temporarily stop all output clocks, don't do this if the chip is generating + the CPU clock for example. + +==Child nodes== + +Each of the clock outputs can be overwritten individually by +using a child node to the I2C device node. If a child node for a clock +output is not set, the configuration remains unchanged. + +Required child node properties: +- reg: number of clock output. + +Optional child node properties: +- silabs,format: Output format, see [1], 1=differential, 2=low-power, 4=LVCMOS +- silabs,common-mode: Output common mode, depends on standard. +- silabs,amplitude: Output amplitude, depends on standard. +- silabs,synth-source: Select which multisynth to use for this output +- silabs,synth-frequency: Sets the frequency for the multisynth connected to + this output. This will affect other outputs connected to this multisynth. The + setting is applied before silabs,synth-master and clock-frequency. +- silabs,synth-master: If present, this output is allowed to change the + multisynth frequency dynamically. +- clock-frequency: Sets a default frequency for this output. +- always-on: Immediately and permanently enable this output. Particulary + useful when combined with assigned-clocks, since that does not prepare clocks. + +==Example== + +/* 48MHz reference crystal */ +ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; +}; + +i2c-master-node { + + /* Programmable clock (for logic) */ + si5341: clock-generator@74 { + reg = <0x74>; + compatible = "silabs,si5341"; + #clock-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + + silabs,pll-m-num = <14000>; /* PLL at 14.0 GHz */ + silabs,pll-m-den = <48>; + silabs,reprogram; /* Chips are not programmed, always reset */ + + /* + * Output 0 configuration: + * LVDS 3v3 + * Source from Multisynth 3 + * Use 600MHz synth frequency, and generate 100MHz from that + * Always keep this clock running + */ + out0 { + /* refclk0 for PS-GT, usually for SATA or PCIe */ + reg = <0>; + silabs,format = <1>; /* LVDS 3v3 */ + silabs,common-mode = <3>; + silabs,amplitude = <3>; + silabs,synth-source = <3>; /* Multisynth 3 */ + silabs,synth-frequency = <600000000>; + silabs,synth-master; + clock-frequency = <10000000>; + always-on; + }; + + /* + * Output 6 configuration: + * LVDS 1v8 + */ + out6 { + /* FPGA clock 200MHz */ + reg = <6>; + silabs,format = <1>; /* LVDS 1v8 */ + silabs,common-mode = <13>; + silabs,amplitude = <3>; + }; + + /* + * Output 8 configuration: + * HCSL 3v3 + * run at 100MHz + */ + out8 { + reg = <8>; + silabs,format = <2>; + silabs,common-mode = <11>; + silabs,amplitude = <3>; + silabs,synth-source = <0>; + clock-frequency = <100000000>; + }; + }; +}; -- 2.17.1