On Monday 13 August 2007, Bjorn Helgaas wrote: > On Saturday 11 August 2007 12:39:35 pm Andrey Borzenkov wrote: > > This stopped working again in 2.6.23-rc. In 2.6.22 we decided to disable > > PnP by default; it is apparently enabled now and fails to activte IrDA > > completely. So it moves to post-2.6.22 regressions :) > > > > let me know which information you need > > > > [ 2192.666450] pnp: PnP ACPI init > > [ 2192.666589] ACPI: bus type pnp registered > > [ 2192.686035] pnp: Device 00:0a activated. > > [ 2192.686089] 00:0a: SMCf010 not responding at SIR 0x100, FIR 0x2e8; > > auto-configuring > > [ 2192.687610] pnp: Device 00:0a disabled. > > [ 2192.693179] pnp: Device 00:0a activated. > > [ 2192.693210] 00:0a: not responding at SIR 0x100, FIR 0x2e8; swapping > > SIR/FIR and reconfiguring > > [ 2192.694720] pnp: Device 00:0a disabled. > > [ 2192.701232] pnp: Device 00:0a activated. > > [ 2192.701259] 00:0a: responds at SIR 0x2e8, FIR 0x100 > > [ 2192.709309] pnp: PnP ACPI: found 12 devices > > [ 2192.709351] ACPI: ACPI bus type pnp unregistered > > > > .... > > > > [ 2207.986550] Detected unconfigured Toshiba laptop with ALi ISA bridge > > SMSC IrDA chip, pre-configuring device. > > [ 2207.986587] Activated ALi 1533 ISA bridge port 0x02e8. > > [ 2207.986602] Activated ALi 1533 ISA bridge port 0x02f8. > > [ 2207.986817] found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): > > LPC47N227 > > [ 2207.986851] smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: > > 7, mode: 0x0e > > [ 2207.986873] smsc_ircc_present: can't get sir_base of 0x2e8 > > As of 2.6.23-rc2, we should have: > - probes for 8250 legacy devices (as in 2.6.21 and previous) > - smsc PNP probes turned off by default (2.6.21 and previous had no > PNP probes for smsc at all) > - some complicated PNP quirks for SMCf010 devices > > In other words, I think we're basically back where we started.
Nope, it is a regression. > The 8250 > driver should find a ttyS3 device at 0x2e8, and it should claim those > ports, which will prevent smsc from claiming them. > This worked in 2.6.22 and does not work in 2.6.23. So something changed. I make a separate post about it because it is probably unrelated to smsc. > If you use "setserial /dev/ttyS3 none", the 8250 driver should release > the ports at 0x2e8, and then the smsc-ircc2 driver should be able to > load correctly. I think this is what we always had to do in the past, > right? > No; it "just worked". I do not even have setserial command ... installed one but this does not support "none" > If that doesn't work, try removing the body of quirk_smc_enable() in > drivers/pnp/quirks.c in addition. It's possible that the quirk changes > the config in a way that messes up the smsc-ircc2 probe. > If I unload 8250 smsc-ircc2 loads just fine.
signature.asc
Description: This is a digitally signed message part.
