Add commands for test and management. Add command space for future development.
Acked-by: Enric Balletbo i Serra <enric.balle...@collabora.com> Acked-by: Benson Leung <ble...@chromium.org> Signed-off-by: Gwendal Grignou <gwen...@chromium.org> --- include/linux/mfd/cros_ec_commands.h | 113 +++++++++++++++++++++++++++ 1 file changed, 113 insertions(+) diff --git a/include/linux/mfd/cros_ec_commands.h b/include/linux/mfd/cros_ec_commands.h index 860a76274334..fc8babce1576 100644 --- a/include/linux/mfd/cros_ec_commands.h +++ b/include/linux/mfd/cros_ec_commands.h @@ -5176,6 +5176,119 @@ struct ec_params_set_cbi { uint8_t data[]; /* For string and raw data */ } __ec_align1; +/* + * Information about resets of the AP by the EC and the EC's own uptime. + */ +#define EC_CMD_GET_UPTIME_INFO 0x0121 + +struct ec_response_uptime_info { + /* + * Number of milliseconds since the last EC boot. Sysjump resets + * typically do not restart the EC's time_since_boot epoch. + * + * WARNING: The EC's sense of time is much less accurate than the AP's + * sense of time, in both phase and frequency. This timebase is similar + * to CLOCK_MONOTONIC_RAW, but with 1% or more frequency error. + */ + uint32_t time_since_ec_boot_ms; + + /* + * Number of times the AP was reset by the EC since the last EC boot. + * Note that the AP may be held in reset by the EC during the initial + * boot sequence, such that the very first AP boot may count as more + * than one here. + */ + uint32_t ap_resets_since_ec_boot; + + /* + * The set of flags which describe the EC's most recent reset. See + * include/system.h RESET_FLAG_* for details. + */ + uint32_t ec_reset_flags; + + /* Empty log entries have both the cause and timestamp set to zero. */ + struct ap_reset_log_entry { + /* + * See include/chipset.h: enum chipset_{reset,shutdown}_reason + * for details. + */ + uint16_t reset_cause; + + /* Reserved for protocol growth. */ + uint16_t reserved; + + /* + * The time of the reset's assertion, in milliseconds since the + * last EC boot, in the same epoch as time_since_ec_boot_ms. + * Set to zero if the log entry is empty. + */ + uint32_t reset_time_ms; + } recent_ap_reset[4]; +} __ec_align4; + +/* + * Add entropy to the device secret (stored in the rollback region). + * + * Depending on the chip, the operation may take a long time (e.g. to erase + * flash), so the commands are asynchronous. + */ +#define EC_CMD_ADD_ENTROPY 0x0122 + +enum add_entropy_action { + /* Add entropy to the current secret. */ + ADD_ENTROPY_ASYNC = 0, + /* + * Add entropy, and also make sure that the previous secret is erased. + * (this can be implemented by adding entropy multiple times until + * all rolback blocks have been overwritten). + */ + ADD_ENTROPY_RESET_ASYNC = 1, + /* Read back result from the previous operation. */ + ADD_ENTROPY_GET_RESULT = 2, +}; + +struct ec_params_rollback_add_entropy { + uint8_t action; +} __ec_align1; + +/* + * Perform a single read of a given ADC channel. + */ +#define EC_CMD_ADC_READ 0x0123 + +struct ec_params_adc_read { + uint8_t adc_channel; +} __ec_align1; + +struct ec_response_adc_read { + int32_t adc_value; +} __ec_align4; + +/* + * Read back rollback info + */ +#define EC_CMD_ROLLBACK_INFO 0x0124 + +struct ec_response_rollback_info { + int32_t id; /* Incrementing number to indicate which region to use. */ + int32_t rollback_min_version; + int32_t rw_rollback_version; +} __ec_align4; + + +/* Issue AP reset */ +#define EC_CMD_AP_RESET 0x0125 + +/*****************************************************************************/ +/* The command range 0x200-0x2FF is reserved for Rotor. */ + +/*****************************************************************************/ +/* + * Reserve a range of host commands for the CR51 firmware. + */ +#define EC_CMD_CR51_BASE 0x0300 +#define EC_CMD_CR51_LAST 0x03FF + /*****************************************************************************/ /* Fingerprint MCU commands: range 0x0400-0x040x */ -- 2.21.0.1020.gf2820cf01a-goog