On Fri, 2019-06-07 at 11:26 +0200, Stefan Wahren wrote:
> Hi Nicolas,
>
> Am 06.06.19 um 16:22 schrieb Nicolas Saenz Julienne:
> > Raspberry Pi's firmware offers an interface though which update it's
> > clock's frequencies. This is specially useful in order to change the CPU
> > clock (pllb_arm) which is 'owned' by the firmware and we're unable to
> > scale using the register interface provided by clk-bcm2835.
> >
> > Signed-off-by: Nicolas Saenz Julienne <nsaenzjulie...@suse.de>
> > Acked-by: Eric Anholt <e...@anholt.net>
> >
> > ---
> >
> > Changes since v1:
> > - Use BIT()
> > - Add Kconfig entry, with compile test
> > - remove prepare/unprepare
> > - Fix uninitialized init.name in pllb registration
> > - Add MODULE_ALIAS()
> > - Use determine_rate() instead of round_rate()
> > - Add small introduction explaining need for driver
> >
> > drivers/clk/bcm/Kconfig | 7 +
> > drivers/clk/bcm/Makefile | 1 +
> > drivers/clk/bcm/clk-raspberrypi.c | 302 ++++++++++++++++++++++++++++++
> > 3 files changed, 310 insertions(+)
> > create mode 100644 drivers/clk/bcm/clk-raspberrypi.c
> >
> > diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
> > index 29ee7b776cd4..a4a2775d65e1 100644
> > --- a/drivers/clk/bcm/Kconfig
> > +++ b/drivers/clk/bcm/Kconfig
> > @@ -64,3 +64,10 @@ config CLK_BCM_SR
> > default ARCH_BCM_IPROC
> > help
> > Enable common clock framework support for the Broadcom Stingray SoC
> > +
> > +config CLK_RASPBERRYPI
> > + tristate "Raspberry Pi firmware based clock support"
> > + depends on RASPBERRYPI_FIRMWARE || (COMPILE_TEST &&
> > !RASPBERRYPI_FIRMWARE)
> > + help
> > + Enable common clock framework support for Raspberry Pi's firmware
> > + dependent clocks
> > diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
> > index 002661d39128..eb7159099d82 100644
> > --- a/drivers/clk/bcm/Makefile
> > +++ b/drivers/clk/bcm/Makefile
> > @@ -7,6 +7,7 @@ obj-$(CONFIG_CLK_BCM_KONA) += clk-bcm21664.o
> > obj-$(CONFIG_COMMON_CLK_IPROC) += clk-iproc-armpll.o clk-iproc-pll.o
> > clk-iproc-asiu.o
> > obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835.o
> > obj-$(CONFIG_ARCH_BCM2835) += clk-bcm2835-aux.o
> > +obj-$(CONFIG_CLK_RASPBERRYPI) += clk-raspberrypi.o
> > obj-$(CONFIG_ARCH_BCM_53573) += clk-bcm53573-ilp.o
> > obj-$(CONFIG_CLK_BCM_CYGNUS) += clk-cygnus.o
> > obj-$(CONFIG_CLK_BCM_HR2) += clk-hr2.o
>
> not your fault but you better rebase your next version on linux-next
> because Florian's latest patches ("clk: bcm: Make BCM2835 clock drivers
> selectable") collide with this patch.
>
> Checkpatch gives the following output about this patch:
>
> WARNING: 'harware' may be misspelled - perhaps 'hardware'?
>
> #58: FILE: drivers/clk/bcm/clk-raspberrypi.c:5:
> + * Even though clk-bcm2835 provides an interface to the harware
> registers for
>
> ERROR: code indent should use tabs where possible
> #197: FILE: drivers/clk/bcm/clk-raspberrypi.c:144:
> +^I^I^I^I struct clk_rate_request *req)$Noted, thanks. As this seems fairly calm, should I send v3 or wait little more?
signature.asc
Description: This is a digitally signed message part
