Add bindings for the new TI CPSW switch driver. Comparing to the legacy bindings (net/cpsw.txt): - ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be marked as "disabled" if not physically wired. - ports definition follows DSA bindings (net/dsa/dsa.txt) and ports can be marked as "disabled" if not physically wired. - all deprecated properties dropped; - all legacy propertiies dropped which represents constant HW cpapbilities (cpdma_channels, ale_entries, bd_ram_size, mac_control, slaves, active_slave) - cpts properties grouped in "cpts" sub-node
Signed-off-by: Grygorii Strashko <[email protected]> --- .../bindings/net/ti,cpsw-switch.txt | 147 ++++++++++++++++++ 1 file changed, 147 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/ti,cpsw-switch.txt diff --git a/Documentation/devicetree/bindings/net/ti,cpsw-switch.txt b/Documentation/devicetree/bindings/net/ti,cpsw-switch.txt new file mode 100644 index 000000000000..787219cddccd --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,cpsw-switch.txt @@ -0,0 +1,147 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings (new) +------------------------------------------------------ + +The 3-port switch gigabit ethernet subsystem provides ethernet packet +communication and can be configured as an ethernet switch. It provides the +gigabit media independent interface (GMII),reduced gigabit media +independent interface (RGMII), reduced media independent interface (RMII), +the management data input output (MDIO) for physical layer device (PHY) +management. + +Required properties: +- compatible : be one of the below: + "ti,cpsw-switch" for backward compatible + "ti,am335x-cpsw-switch" for AM335x controllers + "ti,am4372-cpsw-switch" for AM437x controllers + "ti,dra7-cpsw-switch" for DRA7x controllers +- reg : physical base address and size of the CPSW module IO range +- ranges : shall contain the CPSW module IO range available for child devices +- clocks : should contain the CPSW functional clock +- clock-names : should be "fck" + See bindings/clock/clock-bindings.txt +- interrupts : should contain CPSW RX, TX, MISC, RX_THRESH interrupts +- interrupt-names : should contain "rx_thresh", "rx", "tx", "misc" + See bindings/interrupt-controller/interrupts.txt + +Optional properties: +- syscon : phandle to the system control device node which provides access to + efuse IO range with MAC addresses + +Required Sub-nodes: +- ports : contains CPSW external ports descriptions + Required properties: + - #address-cells : Must be 1 + - #size-cells : Must be 0 + - reg : CPSW port number. Should be 1 or 2 + - phys : phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt) + - phy-mode : operation mode of the PHY interface [1] + - phy-handle : phandle to a PHY on an MDIO bus [1] + + Optional properties: + - ti,label : Describes the label associated with this port + - ti,dual_emac_pvid : Specifies default PORT VID to be used to segregate + ports. Default value - CPSW port number. + - mac-address : array of 6 bytes, specifies the MAC address. Always + accounted first if present [1] + - local-mac-address : See [1] + +- mdio : CPSW MDIO bus block description + - bus_freq : MDIO Bus frequency + See bindings/net/mdio.txt and davinci-mdio.txt + +- cpts : The Common Platform Time Sync (CPTS) module description + - clocks : should contain the CPTS reference clock + - clock-names : should be "cpts" + See bindings/clock/clock-bindings.txt + + Optional properties - all ports: + - cpts_clock_mult : Numerator to convert input clock ticks into ns + - cpts_clock_shift : Denominator to convert input clock ticks into ns + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + +[1] See Documentation/devicetree/bindings/net/ethernet.txt + +Examples - SOC: +mac_sw: ethernet_switch@0 { + compatible = "ti,dra7-cpsw-switch","ti,cpsw-switch"; + reg = <0x0 0x4000>; + ranges = <0 0 0x4000>; + clocks = <&gmac_main_clk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + syscon = <&scm_conf>; + status = "disabled"; + + interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx_thresh", "rx", "tx", "misc" + + ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + ti,label = "port1"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1>; + }; + + cpsw_port2: port@2 { + reg = <2>; + ti,label = "port2"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2>; + }; + }; + + davinci_mdio_sw: mdio@1000 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + reg = <0x1000 0x100>; + }; + + cpts { + clocks = <&gmac_clkctrl DRA7_GMAC_GMAC_CLKCTRL 25>; + clock-names = "cpts"; + }; +}; + +Examples - platform/board: + +&mac_sw { + pinctrl-names = "default", "sleep"; + status = "okay"; +}; + +&cpsw_port1 { + phy-handle = <ðphy0_sw>; + phy-mode = "rgmii"; + ti,dual_emac_pvid = <1>; +}; + +&cpsw_port2 { + phy-handle = <ðphy1_sw>; + phy-mode = "rgmii"; + ti,dual_emac_pvid = <2>; +}; + +&davinci_mdio_sw { + ethphy0_sw: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1_sw: ethernet-phy@1 { + reg = <1>; + }; +}; -- 2.17.1
