Move some register definitions to the per-device array of struct st_lsm6dsx_sensor_settings in order to simplify adding new sensor devices to the driver.
Also, remove completely unused register definitions. Signed-off-by: Martin Kepplinger <[email protected]> --- This is already based on Lorenzo's recent changes: https://lore.kernel.org/linux-iio/[email protected]/T/#u https://lore.kernel.org/linux-iio/[email protected]/T/#u revision history: v2: improve variable names, thanks Lorenzo thanks martin drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h | 6 ++++ drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c | 31 ++++++++++++++------ 2 files changed, 28 insertions(+), 9 deletions(-) diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h index ab1c66615d67..3c47f5d27d30 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx.h @@ -198,6 +198,9 @@ struct st_lsm6dsx_ext_dev_settings { /** * struct st_lsm6dsx_settings - ST IMU sensor settings * @wai: Sensor WhoAmI default value. + * @int1_addr: Control Register address for INT1 + * @int2_addr: Control Register address for INT2 + * @reset_addr: register address for reset/reboot * @max_fifo_size: Sensor max fifo length in FIFO words. * @id: List of hw id/device name supported by the driver configuration. * @odr_table: Hw sensors odr table (Hz + val). @@ -210,6 +213,9 @@ struct st_lsm6dsx_ext_dev_settings { */ struct st_lsm6dsx_settings { u8 wai; + u8 int1_addr; + u8 int2_addr; + u8 reset_addr; u16 max_fifo_size; struct { enum st_lsm6dsx_hw_id hw_id; diff --git a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c index 9aa109428a52..e0d2149625cc 100644 --- a/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c +++ b/drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c @@ -49,17 +49,12 @@ #include "st_lsm6dsx.h" -#define ST_LSM6DSX_REG_INT1_ADDR 0x0d -#define ST_LSM6DSX_REG_INT2_ADDR 0x0e #define ST_LSM6DSX_REG_FIFO_FTH_IRQ_MASK BIT(3) #define ST_LSM6DSX_REG_WHOAMI_ADDR 0x0f -#define ST_LSM6DSX_REG_RESET_ADDR 0x12 #define ST_LSM6DSX_REG_RESET_MASK BIT(0) #define ST_LSM6DSX_REG_BOOT_MASK BIT(7) #define ST_LSM6DSX_REG_BDU_ADDR 0x12 #define ST_LSM6DSX_REG_BDU_MASK BIT(6) -#define ST_LSM6DSX_REG_INT2_ON_INT1_ADDR 0x13 -#define ST_LSM6DSX_REG_INT2_ON_INT1_MASK BIT(5) #define ST_LSM6DSX_REG_ACC_OUT_X_L_ADDR 0x28 #define ST_LSM6DSX_REG_ACC_OUT_Y_L_ADDR 0x2a @@ -72,6 +67,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { { .wai = 0x69, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 1365, .id = { { @@ -170,6 +168,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }, { .wai = 0x69, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 682, .id = { { @@ -268,6 +269,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }, { .wai = 0x6a, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 682, .id = { { @@ -375,6 +379,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }, { .wai = 0x6c, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 512, .id = { { @@ -494,6 +501,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }, { .wai = 0x6b, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 512, .id = { { @@ -584,6 +594,9 @@ static const struct st_lsm6dsx_settings st_lsm6dsx_sensor_settings[] = { }, { .wai = 0x6b, + .int1_addr = 0x0d, + .int2_addr = 0x0e, + .reset_addr = 0x12, .max_fifo_size = 512, .id = { { @@ -1117,10 +1130,10 @@ static int st_lsm6dsx_get_drdy_reg(struct st_lsm6dsx_hw *hw, u8 *drdy_reg) switch (drdy_pin) { case 1: - *drdy_reg = ST_LSM6DSX_REG_INT1_ADDR; + *drdy_reg = hw->settings->int1_addr; break; case 2: - *drdy_reg = ST_LSM6DSX_REG_INT2_ADDR; + *drdy_reg = hw->settings->int2_addr; break; default: dev_err(hw->dev, "unsupported data ready pin\n"); @@ -1220,7 +1233,7 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw) int err; /* device sw reset */ - err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_RESET_ADDR, + err = regmap_update_bits(hw->regmap, hw->settings->reset_addr, ST_LSM6DSX_REG_RESET_MASK, FIELD_PREP(ST_LSM6DSX_REG_RESET_MASK, 1)); if (err < 0) @@ -1229,7 +1242,7 @@ static int st_lsm6dsx_init_device(struct st_lsm6dsx_hw *hw) msleep(50); /* reload trimming parameter */ - err = regmap_update_bits(hw->regmap, ST_LSM6DSX_REG_RESET_ADDR, + err = regmap_update_bits(hw->regmap, hw->settings->reset_addr, ST_LSM6DSX_REG_BOOT_MASK, FIELD_PREP(ST_LSM6DSX_REG_BOOT_MASK, 1)); if (err < 0) -- 2.20.1
