22.07.2019 9:52, Sowjanya Komatineni пишет:
>
> On 7/21/19 11:10 PM, Dmitry Osipenko wrote:
>> 22.07.2019 1:45, Sowjanya Komatineni пишет:
>>> On 7/21/19 2:38 PM, Dmitry Osipenko wrote:
>>>> 21.07.2019 22:40, Sowjanya Komatineni пишет:
>>>>> This patch adds support for clk: tegra210: suspend-resume.
>>>>>
>>>>> All the CAR controller settings are lost on suspend when core
>>>>> power goes off.
>>>>>
>>>>> This patch has implementation for saving and restoring all PLLs
>>>>> and clocks context during system suspend and resume to have the
>>>>> clocks back to same state for normal operation.
>>>>>
>>>>> Acked-by: Thierry Reding <tred...@nvidia.com>
>>>>> Signed-off-by: Sowjanya Komatineni <skomatin...@nvidia.com>
>>>>> ---
>>>>> drivers/clk/tegra/clk-tegra210.c | 68
>>>>> ++++++++++++++++++++++++++++++++++++++--
>>>>> drivers/clk/tegra/clk.c | 14 +++++++++
>>>>> drivers/clk/tegra/clk.h | 1 +
>>>>> 3 files changed, 80 insertions(+), 3 deletions(-)
>>>>>
>>>>> diff --git a/drivers/clk/tegra/clk-tegra210.c
>>>>> b/drivers/clk/tegra/clk-tegra210.c
>>>>> index 55a88c0824a5..68271873acc1 100644
>>>>> --- a/drivers/clk/tegra/clk-tegra210.c
>>>>> +++ b/drivers/clk/tegra/clk-tegra210.c
>>>>> @@ -9,6 +9,7 @@
>>>>> #include <linux/clkdev.h>
>>>>> #include <linux/of.h>
>>>>> #include <linux/of_address.h>
>>>>> +#include <linux/syscore_ops.h>
>>>>> #include <linux/delay.h>
>>>>> #include <linux/export.h>
>>>>> #include <linux/mutex.h>
>>>>> @@ -220,11 +221,15 @@
>>>>> #define CLK_M_DIVISOR_SHIFT 2
>>>>> #define CLK_M_DIVISOR_MASK 0x3
>>>>> +#define CLK_MASK_ARM 0x44
>>>>> +#define MISC_CLK_ENB 0x48
>>>>> +
>>>>> #define RST_DFLL_DVCO 0x2f4
>>>>> #define DVFS_DFLL_RESET_SHIFT 0
>>>>> #define CLK_RST_CONTROLLER_RST_DEV_Y_SET 0x2a8
>>>>> #define CLK_RST_CONTROLLER_RST_DEV_Y_CLR 0x2ac
>>>>> +#define CPU_SOFTRST_CTRL 0x380
>>>>> #define LVL2_CLK_GATE_OVRA 0xf8
>>>>> #define LVL2_CLK_GATE_OVRC 0x3a0
>>>>> @@ -2825,6 +2830,7 @@ static int tegra210_enable_pllu(void)
>>>>> struct tegra_clk_pll_freq_table *fentry;
>>>>> struct tegra_clk_pll pllu;
>>>>> u32 reg;
>>>>> + int ret;
>>>>> for (fentry = pll_u_freq_table; fentry->input_rate;
>>>>> fentry++) {
>>>>> if (fentry->input_rate == pll_ref_freq)
>>>>> @@ -2853,9 +2859,8 @@ static int tegra210_enable_pllu(void)
>>>>> reg |= PLL_ENABLE;
>>>>> writel(reg, clk_base + PLLU_BASE);
>>>>> - readl_relaxed_poll_timeout_atomic(clk_base + PLLU_BASE, reg,
>>>>> - reg & PLL_BASE_LOCK, 2, 1000);
>>>>> - if (!(reg & PLL_BASE_LOCK)) {
>>>>> + ret = tegra210_wait_for_mask(&pllu, PLLU_BASE, PLL_BASE_LOCK);
>>>>> + if (ret) {
>>>> Why this is needed? Was there a bug?
>>>>
>>> during resume pllu init is needed and to use same terga210_init_pllu,
>>> poll_timeout_atomic can't be used as its ony for atomic context.
>>>
>>> So changed to use wait_for_mask which should work in both cases.
>> Atomic variant could be used from any context, not sure what do you
>> mean. The 'atomic' part only means that function won't cause scheduling
>> and that's it.
>
> Sorry, replied incorrect. readx_poll_timeout_atomic uses ktime_get() and
> during resume timekeeping suspend/resume happens later than clock
> suspend/resume. So using tegra210_wait_for_mask.
>
> both timekeeping and clk-tegra210 drivers are registered as syscore but
> not ordered.
Okay, thank you for the clarification.
[snip]
