On 23/07/2019 13:50, Lokesh Vutla wrote: > > > On 23/07/19 4:14 PM, Marc Zyngier wrote: >> Add the required support for the ESPI range, which behave exactly like >> the SPIs of old, only with new funky INTIDs. >> >> Signed-off-by: Marc Zyngier <m...@kernel.org> >> --- >> drivers/irqchip/irq-gic-v3.c | 85 ++++++++++++++++++++++++------ >> include/linux/irqchip/arm-gic-v3.h | 17 +++++- >> 2 files changed, 85 insertions(+), 17 deletions(-) >> >> diff --git a/drivers/irqchip/irq-gic-v3.c b/drivers/irqchip/irq-gic-v3.c >> index 2371e0a70215..d328a8de533f 100644 >> --- a/drivers/irqchip/irq-gic-v3.c >> +++ b/drivers/irqchip/irq-gic-v3.c >> @@ -51,13 +51,16 @@ struct gic_chip_data { >> u32 nr_redist_regions; >> u64 flags; >> bool has_rss; >> - unsigned int irq_nr; >> struct partition_desc *ppi_descs[16]; >> }; >> >> static struct gic_chip_data gic_data __read_mostly; >> static DEFINE_STATIC_KEY_TRUE(supports_deactivate_key); >> >> +#define GIC_ID_NR (1U << GICD_TYPER_ID_BITS(gic_data.rdists.gicd_typer)) >> +#define GIC_LINE_NR GICD_TYPER_SPIS(gic_data.rdists.gicd_typer) >> +#define GIC_ESPI_NR GICD_TYPER_ESPIS(gic_data.rdists.gicd_typer) >> + >> /* >> * The behaviours of RPR and PMR registers differ depending on the value of >> * SCR_EL3.FIQ, and the behaviour of non-secure priority registers of the >> @@ -100,6 +103,7 @@ static DEFINE_PER_CPU(bool, has_rss); >> enum gic_intid_range { >> PPI_RANGE, >> SPI_RANGE, >> + ESPI_RANGE, >> LPI_RANGE, >> __INVALID_RANGE__ >> }; >> @@ -111,6 +115,8 @@ static enum gic_intid_range >> __get_intid_range(irq_hw_number_t hwirq) >> return PPI_RANGE; >> case 32 ... 1019: >> return SPI_RANGE; >> + case ESPI_BASE_INTID ... 8191: > > as per dt documentation, shouldn't the range be > case ESPI_BASE_INTID ... 5119:
Yes, you're right. Although I strongly suspect that someone will bump this limit up again at some point (there is enough space in the new register space for 4k interrupts -- madness). > >> + return ESPI_RANGE; >> case 8192 ... GENMASK(23, 0): >> return LPI_RANGE; >> default: >> @@ -141,6 +147,7 @@ static inline void __iomem *gic_dist_base(struct >> irq_data *d) >> return gic_data_rdist_sgi_base(); >> >> case SPI_RANGE: >> + case ESPI_RANGE: >> /* SPI -> dist_base */ >> return gic_data.dist_base; >> >> @@ -234,6 +241,31 @@ static u32 convert_offset_index(struct irq_data *d, u32 >> offset, u32 *index) >> case SPI_RANGE: >> *index = d->hwirq; >> return offset; >> + case ESPI_RANGE: >> + *index = d->hwirq - ESPI_BASE_INTID; >> + switch (offset) { >> + case GICD_ISENABLER: >> + return GICD_ISENABLERnE; >> + case GICD_ICENABLER: >> + return GICD_ICENABLERnE; >> + case GICD_ISPENDR: >> + return GICD_ISPENDRnE; >> + case GICD_ICPENDR: >> + return GICD_ICPENDRnE; >> + case GICD_ISACTIVER: >> + return GICD_ISACTIVERnE; >> + case GICD_ICACTIVER: >> + return GICD_ICACTIVERnE; >> + case GICD_IPRIORITYR: >> + return GICD_IPRIORITYRnE; >> + case GICD_ICFGR: >> + return GICD_ICFGRnE; >> + case GICD_IROUTER: >> + return GICD_IROUTERnE; >> + default: >> + break; >> + } >> + break; >> default: >> break; >> } >> @@ -316,7 +348,7 @@ static int gic_irq_set_irqchip_state(struct irq_data *d, >> { >> u32 reg; >> >> - if (d->hwirq >= gic_data.irq_nr) /* PPI/SPI only */ >> + if (d->hwirq >= 8192) /* PPI/SPI only */ >> return -EINVAL; >> >> switch (which) { >> @@ -343,7 +375,7 @@ static int gic_irq_set_irqchip_state(struct irq_data *d, >> static int gic_irq_get_irqchip_state(struct irq_data *d, >> enum irqchip_irq_state which, bool *val) >> { >> - if (d->hwirq >= gic_data.irq_nr) /* PPI/SPI only */ >> + if (d->hwirq >= 8192) /* PPI/SPI only */ >> return -EINVAL; >> >> switch (which) { >> @@ -567,7 +599,12 @@ static asmlinkage void __exception_irq_entry >> gic_handle_irq(struct pt_regs *regs >> gic_arch_enable_irqs(); >> } >> >> - if (likely(irqnr > 15 && irqnr < 1020) || irqnr >= 8192) { >> + /* Check for special IDs first */ >> + if ((irqnr >= 1020 && irqnr <= 1023)) >> + return; > > May be I am missing something here, what is special about these 4 interrupts? > or > you meant to check for reserved range here? What's so special about the special INTID range is that these are not interrupts at all. That's how the GIC signals that *something else* is happening (see 2.2.1 "Special INTIDs" in the architecture spec). In practice, and as long as you run Linux in non-secure mode, only 1023 can happen. Thanks, M. -- Jazz is not dead, it just smells funny...