Hi Uwe,
Dne ponedeljek, 29. julij 2019 ob 09:06:05 CEST je Uwe Kleine-König
napisal(a):
> On Fri, Jul 26, 2019 at 08:40:44PM +0200, Jernej Skrabec wrote:
> > PWM core has an option to bypass whole logic and output unchanged source
> > clock as PWM output. This is achieved by enabling bypass bit.
> >
> > Note that when bypass is enabled, no other setting has any meaning, not
> > even enable bit.
> >
> > This mode of operation is needed to achieve high enough frequency to
> > serve as clock source for AC200 chip, which is integrated into same
> > package as H6 SoC.
> >
> > Signed-off-by: Jernej Skrabec <jernej.skra...@siol.net>
> > ---
> >
> > drivers/pwm/pwm-sun4i.c | 31 ++++++++++++++++++++++++++++++-
> > 1 file changed, 30 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/pwm/pwm-sun4i.c b/drivers/pwm/pwm-sun4i.c
> > index 9e0eca79ff88..848cff26f385 100644
> > --- a/drivers/pwm/pwm-sun4i.c
> > +++ b/drivers/pwm/pwm-sun4i.c
> > @@ -120,6 +120,19 @@ static void sun4i_pwm_get_state(struct pwm_chip
> > *chip,
> >
> > val = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
> >
> > + /*
> > + * PWM chapter in H6 manual has a diagram which explains that if
bypass
> > + * bit is set, no other setting has any meaning. Even more,
experiment
> > + * proved that also enable bit is ignored in this case.
> > + */
> > + if (val & BIT_CH(PWM_BYPASS, pwm->hwpwm)) {
> > + state->period = DIV_ROUND_CLOSEST_ULL(NSEC_PER_SEC,
clk_rate);
> > + state->duty_cycle = state->period / 2;
> > + state->polarity = PWM_POLARITY_NORMAL;
> > + state->enabled = true;
> > + return;
> > + }
> > +
> >
> > if ((PWM_REG_PRESCAL(val, pwm->hwpwm) == PWM_PRESCAL_MASK) &&
> >
> > sun4i_pwm->data->has_prescaler_bypass)
> >
> > prescaler = 1;
> >
> > @@ -211,7 +224,8 @@ static int sun4i_pwm_apply(struct pwm_chip *chip,
> > struct pwm_device *pwm,>
> > {
> >
> > struct sun4i_pwm_chip *sun4i_pwm = to_sun4i_pwm_chip(chip);
> > struct pwm_state cstate;
> >
> > - u32 ctrl;
> > + u32 ctrl, clk_rate;
> > + bool bypass;
> >
> > int ret;
> > unsigned int delay_us;
> > unsigned long now;
> >
> > @@ -226,6 +240,16 @@ static int sun4i_pwm_apply(struct pwm_chip *chip,
> > struct pwm_device *pwm,>
> > }
> >
> > }
> >
> > + /*
> > + * Although it would make much more sense to check for bypass in
> > + * sun4i_pwm_calculate(), value of bypass bit also depends on
"enabled".
> > + * Period is allowed to be rounded up or down.
> > + */
>
> Every driver seems to implement rounding the way its driver considers it
> sensible. @Thierry: This is another patch where it would be good to have
> a global directive about how rounding is supposed to work to provide the
> users an reliable and uniform way to work with PWMs.
>
> > + clk_rate = clk_get_rate(sun4i_pwm->clk);
> > + bypass = (state->period == NSEC_PER_SEC / clk_rate ||
> > + state->period == DIV_ROUND_UP(NSEC_PER_SEC, clk_rate))
&&
> > + state->enabled;
>
> Not sure if the compiler is clever enough to notice the obvious
> optimisation with this code construct, but you can write this test in a
> more clever way which has zero instead of up to two divisions. Something
> like:
>
> bypass = ((state->period * clk_rate >= NSEC_PER_SEC &&
> state->period * clk_rate < NSEC_PER_SEC + clk_rate) &&
> state->enabled);
>
> In the commit log you write the motivation for using bypass is that it
> allows to implement higher frequency then with the "normal" operation.
> As you don't skip calculating the normal parameters requesting such a
> high-frequency setting either errors out or doesn't catch the impossible
> request. In both cases there is something to fix.
It's the latter, otherwise it wouldn't work for my case. I'll fix the check and
skip additional logic.
>
> > +
> >
> > spin_lock(&sun4i_pwm->ctrl_lock);
> > ctrl = sun4i_pwm_readl(sun4i_pwm, PWM_CTRL_REG);
> >
> > @@ -273,6 +297,11 @@ static int sun4i_pwm_apply(struct pwm_chip *chip,
> > struct pwm_device *pwm,>
> > ctrl &= ~BIT_CH(PWM_CLK_GATING, pwm->hwpwm);
> >
> > }
> >
> > + if (bypass)
> > + ctrl |= BIT_CH(PWM_BYPASS, pwm->hwpwm);
> > + else
> > + ctrl &= ~BIT_CH(PWM_BYPASS, pwm->hwpwm);
> > +
>
> Does switching on (or off) the bypass bit complete the currently running
> period?
I don't really know. If I understand correctly, it just bypasses PWM logic
completely, so I would say it doesn't complete the currently running period.
Take a look at chapter 3.9.2 http://linux-sunxi.org/
File:Allwinner_H6_V200_User_Manual_V1.1.pdf
Best regards,
Jernej
>
> > sun4i_pwm_writel(sun4i_pwm, ctrl, PWM_CTRL_REG);
> >
> > spin_unlock(&sun4i_pwm->ctrl_lock);
>
> Best regards
> Uwe
