On Wed, May 15, 2019 at 04:49:25PM +0800, Yinbo Zhu wrote: > From: Ashish Kumar <ashish.ku...@nxp.com> > > This patch is to add esdhc node and enable SD UHS-I, > eMMC HS200 for ls1028ardb/ls1028aqds board. > > Signed-off-by: Ashish Kumar <ashish.ku...@nxp.com> > Signed-off-by: Yangbo Lu <yangbo...@nxp.com> > Signed-off-by: Yinbo Zhu <yinbo....@nxp.com> > --- > Change in v3: > replace "esdhc@" with "mmc@" > > arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 8 ++++++ > arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 13 ++++++++++ > arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 27 > +++++++++++++++++++++ > 3 files changed, 48 insertions(+), 0 deletions(-) > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts > b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts > index 14c79f4..180e5d2 100644 > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts > @@ -42,6 +42,14 @@ > status = "okay"; > }; > > +&esdhc { > + status = "okay"; > +}; > + > +&esdhc1 { > + status = "okay"; > +}; > + > &i2c0 { > status = "okay"; > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts > b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts > index f86b054..1bfaf42 100644 > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts > @@ -30,6 +30,19 @@ > }; > }; > > +&esdhc { > + status = "okay";
We usually put 'status' at end of property list. > + sd-uhs-sdr104; > + sd-uhs-sdr50; > + sd-uhs-sdr25; > + sd-uhs-sdr12; > + }; Please follow the indent style of closing parentheses in the file. > + > +&esdhc1 { > + status = "okay"; > + mmc-hs200-1_8v; > + }; Ditto > + > &i2c0 { > status = "okay"; > > diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > index 2896bbc..462833c 100644 > --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi > @@ -274,6 +274,33 @@ > status = "disabled"; > }; > > + esdhc: mmc@2140000 { Please sort the nodes in unit-address. From what I see, it should go before device serial@21c0500. > + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; > + reg = <0x0 0x2140000 0x0 0x10000>; > + interrupts = <0 28 0x4>; /* Level high type */ Use IRQ_TYPE_LEVEL_HIGH, then you can drop the comment. Shawn > + clock-frequency = <0>; /* fixed up by bootloader */ > + clocks = <&clockgen 2 1>; > + voltage-ranges = <1800 1800 3300 3300>; > + sdhci,auto-cmd12; > + little-endian; > + bus-width = <4>; > + status = "disabled"; > + }; > + > + esdhc1: mmc@2150000 { > + compatible = "fsl,ls1028a-esdhc", "fsl,esdhc"; > + reg = <0x0 0x2150000 0x0 0x10000>; > + interrupts = <0 63 0x4>; /* Level high type */ > + clock-frequency = <0>; /* fixed up by bootloader */ > + clocks = <&clockgen 2 1>; > + voltage-ranges = <1800 1800 3300 3300>; > + sdhci,auto-cmd12; > + broken-cd; > + little-endian; > + bus-width = <4>; > + status = "disabled"; > + }; > + > sata: sata@3200000 { > compatible = "fsl,ls1028a-ahci"; > reg = <0x0 0x3200000 0x0 0x10000>, > -- > 1.7.1 >