On Mon, Aug 05, 2019 at 07:54:42PM +0300, Alexandru Ardelean wrote:
> The ADIN1300 chip supports RGMII, RMII & MII modes. Default (if
> unconfigured) is RGMII.
> This change adds support for configuring these modes via the device
> registers.
>
> For RGMII with internal delays (modes RGMII_ID,RGMII_TXID, RGMII_RXID),
It would be nice to add the missing space.
> the default delay is 2 ns. This can be configurable and will be done in
> a subsequent change.
>
> Signed-off-by: Alexandru Ardelean <alexandru.ardel...@analog.com>
> ---
> drivers/net/phy/adin.c | 79 +++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 78 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> index 3dd9fe50f4c8..dbdb8f60741c 100644
> --- a/drivers/net/phy/adin.c
> +++ b/drivers/net/phy/adin.c
> @@ -33,14 +33,91 @@
> ADIN1300_INT_HW_IRQ_EN)
> #define ADIN1300_INT_STATUS_REG 0x0019
>
> +#define ADIN1300_GE_RGMII_CFG_REG 0xff23
> +#define ADIN1300_GE_RGMII_RXID_EN BIT(2)
> +#define ADIN1300_GE_RGMII_TXID_EN BIT(1)
> +#define ADIN1300_GE_RGMII_EN BIT(0)
> +
> +#define ADIN1300_GE_RMII_CFG_REG 0xff24
> +#define ADIN1300_GE_RMII_EN BIT(0)
> +
> +static int adin_config_rgmii_mode(struct phy_device *phydev,
> + phy_interface_t intf)
> +{
> + int reg;
> +
> + reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RGMII_CFG_REG);
> + if (reg < 0)
> + return reg;
> +
> + if (!phy_interface_mode_is_rgmii(intf)) {
> + reg &= ~ADIN1300_GE_RGMII_EN;
> + goto write;
> + }
> +
> + reg |= ADIN1300_GE_RGMII_EN;
> +
> + if (intf == PHY_INTERFACE_MODE_RGMII_ID ||
> + intf == PHY_INTERFACE_MODE_RGMII_RXID) {
> + reg |= ADIN1300_GE_RGMII_RXID_EN;
> + } else {
> + reg &= ~ADIN1300_GE_RGMII_RXID_EN;
> + }
> +
> + if (intf == PHY_INTERFACE_MODE_RGMII_ID ||
> + intf == PHY_INTERFACE_MODE_RGMII_TXID) {
> + reg |= ADIN1300_GE_RGMII_TXID_EN;
> + } else {
> + reg &= ~ADIN1300_GE_RGMII_TXID_EN;
> + }
Nice. Often driver writers forget to clear the delay, they only set
it. Not so here.
However, is checkpatch happy with this? Each half of the if/else is a
single statement, so the {} are not needed.
> +
> +write:
> + return phy_write_mmd(phydev, MDIO_MMD_VEND1,
> + ADIN1300_GE_RGMII_CFG_REG, reg);
> +}
> +
> +static int adin_config_rmii_mode(struct phy_device *phydev,
> + phy_interface_t intf)
> +{
> + int reg;
> +
> + reg = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN1300_GE_RMII_CFG_REG);
> + if (reg < 0)
> + return reg;
> +
> + if (intf != PHY_INTERFACE_MODE_RMII) {
> + reg &= ~ADIN1300_GE_RMII_EN;
> + goto write;
goto? Really?
> + }
> +
> + reg |= ADIN1300_GE_RMII_EN;
> +
> +write:
> + return phy_write_mmd(phydev, MDIO_MMD_VEND1,
> + ADIN1300_GE_RMII_CFG_REG, reg);
> +}
> +
> static int adin_config_init(struct phy_device *phydev)
> {
> - int rc;
> + phy_interface_t interface, rc;
genphy_config_init() does not return a phy_interface_t!
>
> rc = genphy_config_init(phydev);
> if (rc < 0)
> return rc;
>
> + interface = phydev->interface;
> +
> + rc = adin_config_rgmii_mode(phydev, interface);
> + if (rc < 0)
> + return rc;
> +
> + rc = adin_config_rmii_mode(phydev, interface);
> + if (rc < 0)
> + return rc;
> +
> + dev_info(&phydev->mdio.dev, "PHY is using mode '%s'\n",
> + phy_modes(phydev->interface));
phydev_dbg(), or not at all.
Andrew
