On Tue, Aug 20, 2019 at 01:56:53PM +0200, Michal Vokáč wrote: > On 13. 08. 19 16:04, Benjamin Tissoires wrote: > > On Mon, Aug 12, 2019 at 7:11 PM Dmitry Torokhov > > <dmitry.torok...@gmail.com> wrote: > > > > > > Hi Benjamin, > > > > > > On Mon, Aug 12, 2019 at 06:50:38PM +0200, Benjamin Tissoires wrote: > > > > Hi Dmitry, > > > > > > > > On Fri, Aug 9, 2019 at 7:35 PM Dmitry Torokhov > > > > <dmitry.torok...@gmail.com> wrote: > > > > > > > > > > Separating "normal" and "polled" input devices was a mistake, as > > > > > often we > > > > > want to allow the very same device work on both interrupt-driven and > > > > > polled mode, depending on the board on which the device is used. > > > > > > > > > > This introduces new APIs: > > > > > > > > > > - input_setup_polling > > > > > - input_set_poll_interval > > > > > - input_set_min_poll_interval > > > > > - input_set_max_poll_interval > > > > > > > > > > These new APIs allow switching an input device into polled mode with > > > > > sysfs > > > > > attributes matching drivers using input_polled_dev APIs that will be > > > > > eventually removed. > > > > > > > > Are you sure that using sysfs is the correct way here? > > > > I would think using generic properties that can be overwritten by the > > > > DSDT or by the device tree would make things easier from a driver > > > > point of view. > > > > > > Couple of points: I wanted it to be compatible with input-polldev.c so > > > the sysfs attributes must match (so that we can convert existing drivers > > > and zap input-polldev). > > > > Oh, I missed that. Good point. > > > > > I also am not sure if polling parameters are > > > property of board, or it is either fundamental hardware limitation or > > > simply desired system behavior. > > > > I think it's a combination of everything: sometimes the board misses > > the capability to not do IRQs for that device, and using properties > > would be better here: you can define them where you need (board, > > platform or device level), and have a working platfrom from the kernel > > description entirely. > > However, it doesn't solve the issue of input-polldev, so maybe > > properties should be added on top of this sysfs. > > > > > If Rob is OK with adding device > > > properties I'd be fine adding them as a followup, otherwise we can have > > > udev adjust the behavior as needed for given box shortly after boot. > > > > Fair enough. > > > > > > > > > > > > > Also, checkpatch complains about a few octal permissions that are > > > > preferred over symbolic ones, and there is a possible 'out of memory' > > > > nessage at drivers/input/input-poller.c:75. > > > > > > Yes, there is. It is there so we would know what device we were trying > > > to set up when OOM happened. You can probable decipher the driver from > > > the stack trace, but figuring particular device instance is harder. > > > > Could you add a comment there explaining this choice? I have a feeling > > you'll have to refuse a few patches of people running coccinelle > > scripts and be too happy to send a kernel patch.
Done. > > > > Other than that: > > Acked-by: Benjamin Tissoires <benjamin.tissoi...@redhat.com> > > > > Hi Dmitry, > > what is the status of this patch? Are we still waiting for Rob to > comment on the device properties or is this ready to land? I applied it just now. > > Little bit OT question: what tree/branch do you use to apply patches? > According to the mailing list you recently applied some patches but > I can not find them here [1]. Patches that go into current cycle will be in 'for-linus' branch. Patches that will be merged in the next merge window (like this one) will end up in 'next' branch. Thanks. -- Dmitry