On 10/09/19 11:06:55, Guenter Roeck wrote:
> On Fri, Sep 06, 2019 at 10:54:10PM +0200, Jorge Ramirez-Ortiz wrote:
> > Use the bark interrupt as the pre-timeout notifier whenever this
> > interrupt is available.
> >
> > By default, the pretimeout notification shall occur one second earlier
> > than the timeout.
> >
> > Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-or...@linaro.org>
>
> Nitpick below, otherwise:
>
> Reviewed-by: Guenter Roeck <li...@roeck-us.net>
>
> > ---
> > drivers/watchdog/qcom-wdt.c | 70 ++++++++++++++++++++++++++++++++++---
> > 1 file changed, 65 insertions(+), 5 deletions(-)
> >
> > diff --git a/drivers/watchdog/qcom-wdt.c b/drivers/watchdog/qcom-wdt.c
> > index 7be7f87be28f..935c78a882a3 100644
> > --- a/drivers/watchdog/qcom-wdt.c
> > +++ b/drivers/watchdog/qcom-wdt.c
> > @@ -1,8 +1,10 @@
> > // SPDX-License-Identifier: GPL-2.0-only
> > /* Copyright (c) 2014, The Linux Foundation. All rights reserved.
> > */
> > +#include <linux/bits.h>
> > #include <linux/clk.h>
> > #include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > #include <linux/io.h>
> > #include <linux/kernel.h>
> > #include <linux/module.h>
> > @@ -19,6 +21,9 @@ enum wdt_reg {
> > WDT_BITE_TIME,
> > };
> >
> > +#define QCOM_WDT_ENABLE BIT(0)
> > +#define QCOM_WDT_ENABLE_IRQ BIT(1)
> > +
> > static const u32 reg_offset_data_apcs_tmr[] = {
> > [WDT_RST] = 0x38,
> > [WDT_EN] = 0x40,
> > @@ -54,15 +59,35 @@ struct qcom_wdt *to_qcom_wdt(struct watchdog_device
> > *wdd)
> > return container_of(wdd, struct qcom_wdt, wdd);
> > }
> >
> > +static inline int qcom_get_enable(struct watchdog_device *wdd)
> > +{
> > + int enable = QCOM_WDT_ENABLE;
> > +
> > + if (wdd->pretimeout)
> > + enable |= QCOM_WDT_ENABLE_IRQ;
> > +
> > + return enable;
> > +}
> > +
> > +static irqreturn_t qcom_wdt_isr(int irq, void *arg)
> > +{
> > + struct watchdog_device *wdd = arg;
> > +
> > + watchdog_notify_pretimeout(wdd);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > static int qcom_wdt_start(struct watchdog_device *wdd)
> > {
> > struct qcom_wdt *wdt = to_qcom_wdt(wdd);
> > + unsigned int bark = wdd->timeout - wdd->pretimeout;
> >
> > writel(0, wdt_addr(wdt, WDT_EN));
> > writel(1, wdt_addr(wdt, WDT_RST));
> > - writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> > + writel(bark * wdt->rate, wdt_addr(wdt, WDT_BARK_TIME));
> > writel(wdd->timeout * wdt->rate, wdt_addr(wdt, WDT_BITE_TIME));
> > - writel(1, wdt_addr(wdt, WDT_EN));
> > + writel(qcom_get_enable(wdd), wdt_addr(wdt, WDT_EN));
> > return 0;
> > }
> >
> > @@ -89,6 +114,13 @@ static int qcom_wdt_set_timeout(struct watchdog_device
> > *wdd,
> > return qcom_wdt_start(wdd);
> > }
> >
> > +static int qcom_wdt_set_pretimeout(struct watchdog_device *wdd,
> > + unsigned int timeout)
> > +{
> > + wdd->pretimeout = timeout;
> > + return qcom_wdt_start(wdd);
> > +}
> > +
> > static int qcom_wdt_restart(struct watchdog_device *wdd, unsigned long
> > action,
> > void *data)
> > {
> > @@ -105,7 +137,7 @@ static int qcom_wdt_restart(struct watchdog_device
> > *wdd, unsigned long action,
> > writel(1, wdt_addr(wdt, WDT_RST));
> > writel(timeout, wdt_addr(wdt, WDT_BARK_TIME));
> > writel(timeout, wdt_addr(wdt, WDT_BITE_TIME));
> > - writel(1, wdt_addr(wdt, WDT_EN));
> > + writel(QCOM_WDT_ENABLE, wdt_addr(wdt, WDT_EN));
> >
> > /*
> > * Actually make sure the above sequence hits hardware before sleeping.
> > @@ -121,6 +153,7 @@ static const struct watchdog_ops qcom_wdt_ops = {
> > .stop = qcom_wdt_stop,
> > .ping = qcom_wdt_ping,
> > .set_timeout = qcom_wdt_set_timeout,
> > + .set_pretimeout = qcom_wdt_set_pretimeout,
> > .restart = qcom_wdt_restart,
> > .owner = THIS_MODULE,
> > };
> > @@ -133,6 +166,15 @@ static const struct watchdog_info qcom_wdt_info = {
> > .identity = KBUILD_MODNAME,
> > };
> >
> > +static const struct watchdog_info qcom_wdt_pt_info = {
> > + .options = WDIOF_KEEPALIVEPING
> > + | WDIOF_MAGICCLOSE
> > + | WDIOF_SETTIMEOUT
> > + | WDIOF_PRETIMEOUT
> > + | WDIOF_CARDRESET,
> > + .identity = KBUILD_MODNAME,
> > +};
> > +
> > static void qcom_clk_disable_unprepare(void *data)
> > {
> > clk_disable_unprepare(data);
> > @@ -146,7 +188,7 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> > struct device_node *np = dev->of_node;
> > const u32 *regs;
> > u32 percpu_offset;
> > - int ret;
> > + int irq, ret;
> >
> > regs = of_device_get_match_data(dev);
> > if (!regs) {
> > @@ -204,7 +246,25 @@ static int qcom_wdt_probe(struct platform_device *pdev)
> > return -EINVAL;
> > }
> >
> > - wdt->wdd.info = &qcom_wdt_info;
> > + /* check if there is pretimeout support */
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq > 0) {
> > + ret = devm_request_irq(dev, irq, qcom_wdt_isr,
> > + IRQF_TRIGGER_RISING,
> > + "wdt_bark", &wdt->wdd);
> > + if (ret)
> > + return ret;
> > +
> > + wdt->wdd.info = &qcom_wdt_pt_info;
> > + wdt->wdd.pretimeout = 1;
> > + } else {
> > + if (irq == -EPROBE_DEFER)
> > + return -EPROBE_DEFER;
> > +
> > + wdt->wdd.info = &qcom_wdt_info;
> > + wdt->wdd.pretimeout = 0;
>
> It is not necessary to set pretimeout to 0; the data structure was
> allocated with devm_kzalloc(). The compiler won't know that and
> generate unnecessary code otherwise.
will you need me to send another version or could you pick it up as is?
>
> > + }
> > +
> > wdt->wdd.ops = &qcom_wdt_ops;
> > wdt->wdd.min_timeout = 1;
> > wdt->wdd.max_timeout = 0x10000000U / wdt->rate;
