[PATCH V2 1/3] arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort

[Anson Huang]

The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.

Signed-off-by: Anson Huang <anson.hu...@nxp.com>
---
new patch.
---
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 124 +++++++++++++--------------
 1 file changed, 62 insertions(+), 62 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts 
b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index f7a15f3..f6d367c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -94,68 +94,6 @@
        };
 };
 
-&sai3 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinctrl_sai3>;
-       assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
-       assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
-       assigned-clock-rates = <24576000>;
-       status = "okay";
-};
-
-&snvs_pwrkey {
-       status = "okay";
-};
-
-&uart2 { /* console */
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinctrl_uart2>;
-       status = "okay";
-};
-
-&usbotg1 {
-       dr_mode = "otg";
-       hnp-disable;
-       srp-disable;
-       adp-disable;
-       usb-role-switch;
-       status = "okay";
-
-       port {
-               usb1_drd_sw: endpoint {
-                       remote-endpoint = <&typec1_dr_sw>;
-               };
-       };
-};
-
-&usdhc2 {
-       pinctrl-names = "default", "state_100mhz", "state_200mhz";
-       pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
-       pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
-       pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
-       cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-       bus-width = <4>;
-       vmmc-supply = <&reg_usdhc2_vmmc>;
-       status = "okay";
-};
-
-&usdhc3 {
-       pinctrl-names = "default", "state_100mhz", "state_200mhz";
-       pinctrl-0 = <&pinctrl_usdhc3>;
-       pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-       pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
-       bus-width = <8>;
-       non-removable;
-       status = "okay";
-};
-
-&wdog1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&pinctrl_wdog>;
-       fsl,ext-reset-output;
-       status = "okay";
-};
-
 &i2c1 {
        clock-frequency = <400000>;
        pinctrl-names = "default";
@@ -306,6 +244,68 @@
        };
 };
 
+&sai3 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_sai3>;
+       assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+       assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+       assigned-clock-rates = <24576000>;
+       status = "okay";
+};
+
+&snvs_pwrkey {
+       status = "okay";
+};
+
+&uart2 { /* console */
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart2>;
+       status = "okay";
+};
+
+&usbotg1 {
+       dr_mode = "otg";
+       hnp-disable;
+       srp-disable;
+       adp-disable;
+       usb-role-switch;
+       status = "okay";
+
+       port {
+               usb1_drd_sw: endpoint {
+                       remote-endpoint = <&typec1_dr_sw>;
+               };
+       };
+};
+
+&usdhc2 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+       cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+       bus-width = <4>;
+       vmmc-supply = <&reg_usdhc2_vmmc>;
+       status = "okay";
+};
+
+&usdhc3 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc3>;
+       pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+       pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       bus-width = <8>;
+       non-removable;
+       status = "okay";
+};
+
+&wdog1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_wdog>;
+       fsl,ext-reset-output;
+       status = "okay";
+};
+
 &iomuxc {
        pinctrl-names = "default";
 
-- 
2.7.4