usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <anson.hu...@nxp.com>
---
arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 4 ++++
arch/arm64/boot/dts/freescale/imx8mn.dtsi | 4 ----
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 1b90faac..5c96203 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -186,6 +186,8 @@
};
&usdhc2 {
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
+ assigned-clock-rates = <200000000>;
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
@@ -197,6 +199,8 @@
};
&usdhc3 {
+ assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
pinctrl-names = "default", "state_100mhz", "state_200mhz";
pinctrl-0 = <&pinctrl_usdhc3>;
pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
index 73e3711..46c218e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -598,8 +598,6 @@
<&clk IMX8MN_CLK_NAND_USDHC_BUS>,
<&clk IMX8MN_CLK_USDHC1_ROOT>;
clock-names = "ipg", "ahb", "per";
- assigned-clocks = <&clk IMX8MN_CLK_USDHC1>;
- assigned-clock-rates = <400000000>;
fsl,tuning-start-tap = <20>;
fsl,tuning-step= <2>;
bus-width = <4>;
@@ -628,8 +626,6 @@
<&clk IMX8MN_CLK_NAND_USDHC_BUS>,
<&clk IMX8MN_CLK_USDHC3_ROOT>;
clock-names = "ipg", "ahb", "per";
- assigned-clocks = <&clk IMX8MN_CLK_USDHC3_ROOT>;
- assigned-clock-rates = <400000000>;
fsl,tuning-start-tap = <20>;
fsl,tuning-step= <2>;
bus-width = <4>;
--
2.7.4
