On Sun, Jan 07, 2001 at 03:52:41PM -0800, Linus Torvalds wrote:
> In article <[EMAIL PROTECTED]>,
> Philip Armstrong <[EMAIL PROTECTED]> wrote:
> >In supplement to Evan Thompson's emails with the subject "Additional
> >info. for PCI VIA IDE crazyness. Please read." I've noticed the
> >following message with recent 2.4.0 test + release kernels:
> >
> >IRQ routing conflict in pirq table! Try 'pci=autoirq'
>
> But the machine still works fine, ie the SCSI driver and the network
> driver still seem happy?
Just plugged the laptop back in. Yup. Everything seems happy; SCSI,
network etc,etc all doing their thing.
> If so, it sounds like maybe the VIA pirq router functions are buggy (it
> looks like the sense of pirq 01 and pirq 03 are reversed).
[snip]
> looks like Christian, too, has a working machine, and that the only bad
> result of this all is an annoying printk message. Can you confirm that
> things actually work for you too, and you'd just like to get rid of the
> unnerving message?
So long as there's no underlying problem then I don't particularly
care! Though removing the Try 'pci=autoirq' bit (which doesn't do
anything any more as far as I can see) might be sensible...
> If the VIA logic for getting/setting the irq is wrong, it should only be
> a problem if there are devices that _haven't_ been routed by the BIOS.
> Usually these devices are limited to things like USB, ACPI and CardBus
> controllers, and getting the irq routing wrong in that case can be
> deadly (infinite irq streams on the wrong irq line).
I've turned USB off in the BIOS setup altogether. However, in the
recent past I've used a USB webcam which appeared to work (this was in
2.4.0test4 days or thereabouts.)
> The case where you get an annoying message are the cases where Linux
> knows something is wrong, but decides to take the safe approach - it
> seems to be working for you, as far as I can tell, but that message
> _does_ mean that we may have problems on other machines with the VIA
> chipset.
>
> I _think_ the VIA routing functions were done by Jeff Garzik, Cc'd.
>
> Looking at the VIA irq routing, it looks a bit strange. We have pirqa in
> the high nybble of config sparce port 55h, then we have pirqb and c in
> 56h (low and high nybbles respectively), and then we have pirqd in the
> high nybble of 57h.
>
> The reason this is strange is that it's not consecutive nybbles. I'd
> have expected pirqd to show up in the _low_ nybble of 57h. But as the
> pirq routing fields are pure software convention, it's hard to know
> whether this is already taken into account in the pirq routing table or
> what the magic is.
>
> Could anybody with a VIA chip who has the energy please do something for
> me:
> - enable DEBUG in arch/i386/kernel/pci-i386.h
done
> - do a "/sbin/lspci -xxvvv" on the interrupt routing chip (it's the
> "ISA bridge" chip - the VIA numbers are 82c586, 82c596, the PCI
> numbers for them are 1106:0586 and 1106:0596, I think)
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 41)
Subsystem: VIA Technologies, Inc. MVP3 ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort -
<MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 86 05 8f 00 00 02 41 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> - do a cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev 3).
Master Capable. Latency=16.
Prefetchable 32 bit memory at 0xe0000000 [0xe7ffffff].
Bus 0, device 1, function 0:
PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (rev 0).
Master Capable. No bursts. Min Gnt=12.
Bus 0, device 7, function 0:
ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 65).
Bus 0, device 7, function 1:
IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 6).
Master Capable. Latency=64.
I/O at 0xe000 [0xe00f].
Bus 0, device 7, function 2:
USB Controller: VIA Technologies, Inc. UHCI USB (rev 2).
IRQ 10.
Master Capable. Latency=64.
I/O at 0xe400 [0xe41f].
Bus 0, device 7, function 3:
Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 16).
Bus 0, device 8, function 0:
SCSI storage controller: Advanced System Products, Inc ABP940-U / ABP960-U (rev 3).
IRQ 11.
Master Capable. Latency=64. Min Gnt=4.Max Lat=4.
I/O at 0xe800 [0xe8ff].
Non-prefetchable 32 bit memory at 0xef100000 [0xef1000ff].
Bus 0, device 10, function 0:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139 (rev 16).
IRQ 9.
Master Capable. Latency=64. Min Gnt=32.Max Lat=64.
I/O at 0xec00 [0xecff].
Non-prefetchable 32 bit memory at 0xef101000 [0xef1010ff].
Bus 0, device 11, function 0:
Multimedia controller: Sigma Designs, Inc. REALmagic Hollywood Plus DVD Decoder
(rev 1).
IRQ 9.
Master Capable. Latency=64.
Non-prefetchable 32 bit memory at 0xef000000 [0xef0fffff].
Bus 0, device 12, function 0:
Multimedia video controller: 3Dfx Interactive, Inc. Voodoo 2 (rev 2).
Prefetchable 32 bit memory at 0xee000000 [0xeeffffff].
Bus 1, device 0, function 0:
VGA compatible controller: Matrox Graphics, Inc. MGA 2164W [Millennium II] AGP
(rev 0).
IRQ 11.
Master Capable. Latency=64.
Prefetchable 32 bit memory at 0xec000000 [0xecffffff].
Non-prefetchable 32 bit memory at 0xe8000000 [0xe8003fff].
Non-prefetchable 32 bit memory at 0xe9000000 [0xe97fffff].
> With that, I and Jeff can probably match up the interrupt routing table
> entries with the devices, and check what the routing information in the
> config space of the actual router chip is, to verify what the pirq
> translation really should be.
Hope the above is of some use.
cheers,
Phil
--
http://www.kantaka.co.uk/ .oOo. public key: http://www.kantaka.co.uk/gpg.txt
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/
