From: Russell King <rmk+ker...@armlinux.org.uk> [ Upstream commit 3138a07ce219acde4c0d7ea0b6d54ba64153328b ]
When rxhash is enabled on any ethernet port except the first in each CP block, traffic flow is prevented. The analysis is below: I've been investigating this afternoon, and what I've found, comparing a kernel without 895586d5dc32 and with 895586d5dc32 applied is: - The table programmed into the hardware via mvpp22_rss_fill_table() appears to be identical with or without the commit. - When rxhash is enabled on eth2, mvpp2_rss_port_c2_enable() reports that c2.attr[0] and c2.attr[2] are written back containing: - with 895586d5dc32, failing: 00200000 40000000 - without 895586d5dc32, working: 04000000 40000000 - When disabling rxhash, c2.attr[0] and c2.attr[2] are written back as: 04000000 00000000 The second value represents the MVPP22_CLS_C2_ATTR2_RSS_EN bit, the first value is the queue number, which comprises two fields. The high 5 bits are 24:29 and the low three are 21:23 inclusive. This comes from: c2.attr[0] = MVPP22_CLS_C2_ATTR0_QHIGH(qh) | MVPP22_CLS_C2_ATTR0_QLOW(ql); So, the working case gives eth2 a queue id of 4.0, or 32 as per port->first_rxq, and the non-working case a queue id of 0.1, or 1. The allocation of queue IDs seems to be in mvpp2_port_probe(): if (priv->hw_version == MVPP21) port->first_rxq = port->id * port->nrxqs; else port->first_rxq = port->id * priv->max_port_rxqs; Where: if (priv->hw_version == MVPP21) priv->max_port_rxqs = 8; else priv->max_port_rxqs = 32; Making the port 0 (eth0 / eth1) have port->first_rxq = 0, and port 1 (eth2) be 32. It seems the idea is that the first 32 queues belong to port 0, the second 32 queues belong to port 1, etc. mvpp2_rss_port_c2_enable() gets the queue number from it's parameter, 'ctx', which comes from mvpp22_rss_ctx(port, 0). This returns port->rss_ctx[0]. mvpp22_rss_context_create() is responsible for allocating that, which it does by looking for an unallocated priv->rss_tables[] pointer. This table is shared amongst all ports on the CP silicon. When we write the tables in mvpp22_rss_fill_table(), the RSS table entry is defined by: u32 sel = MVPP22_RSS_INDEX_TABLE(rss_ctx) | MVPP22_RSS_INDEX_TABLE_ENTRY(i); where rss_ctx is the context ID (queue number) and i is the index in the table. If we look at what is written: - The first table to be written has "sel" values of 00000000..0000001f, containing values 0..3. This appears to be for eth1. This is table 0, RX queue number 0. - The second table has "sel" values of 00000100..0000011f, and appears to be for eth2. These contain values 0x20..0x23. This is table 1, RX queue number 0. - The third table has "sel" values of 00000200..0000021f, and appears to be for eth3. These contain values 0x40..0x43. This is table 2, RX queue number 0. How do queue numbers translate to the RSS table? There is another table - the RXQ2RSS table, indexed by the MVPP22_RSS_INDEX_QUEUE field of MVPP22_RSS_INDEX and accessed through the MVPP22_RXQ2RSS_TABLE register. Before 895586d5dc32, it was: mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(port->first_rxq)); mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(port->id)); and after: mvpp2_write(priv, MVPP22_RSS_INDEX, MVPP22_RSS_INDEX_QUEUE(ctx)); mvpp2_write(priv, MVPP22_RXQ2RSS_TABLE, MVPP22_RSS_TABLE_POINTER(ctx)); Before the commit, for eth2, that would've contained '32' for the index and '1' for the table pointer - mapping queue 32 to table 1. Remember that this is queue-high.queue-low of 4.0. After the commit, we appear to map queue 1 to table 1. That again looks fine on the face of it. Section 9.3.1 of the A8040 manual seems indicate the reason that the queue number is separated. queue-low seems to always come from the classifier, whereas queue-high can be from the ingress physical port number or the classifier depending on the MVPP2_CLS_SWFWD_PCTRL_REG. We set the port bit in MVPP2_CLS_SWFWD_PCTRL_REG, meaning that queue-high comes from the MVPP2_CLS_SWFWD_P2HQ_REG() register... and this seems to be where our bug comes from. mvpp2_cls_oversize_rxq_set() sets this up as: mvpp2_write(port->priv, MVPP2_CLS_SWFWD_P2HQ_REG(port->id), (port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS)); val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG); val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id); mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val); Setting the MVPP2_CLS_SWFWD_PCTRL_MASK bit means that the queue-high for eth2 is _always_ 4, so only queues 32 through 39 inclusive are available to eth2. Yet, we're trying to tell the classifier to set queue-high, which will be ignored, to zero. Hence, the queue-high field (MVPP22_CLS_C2_ATTR0_QHIGH()) from the classifier will be ignored. This means we end up directing traffic from eth2 not to queue 1, but to queue 33, and then we tell it to look up queue 33 in the RSS table. However, RSS table has not been programmed for queue 33, and so it ends up (presumably) dropping the packets. It seems that mvpp22_rss_context_create() doesn't take account of the fact that the upper 5 bits of the queue ID can't actually be changed due to the settings in mvpp2_cls_oversize_rxq_set(), _or_ it seems that mvpp2_cls_oversize_rxq_set() has been missed in this commit. Either way, these two functions mutually disagree with what queue number should be used. Looking deeper into what mvpp2_cls_oversize_rxq_set() and the MTU validation is doing, it seems that MVPP2_CLS_SWFWD_P2HQ_REG() is used for over-sized packets attempting to egress through this port. With the classifier having had RSS enabled and directing eth2 traffic to queue 1, we may still have packets appearing on queue 32 for this port. However, the only way we may end up with over-sized packets attempting to egress through eth2 - is if the A8040 forwards frames between its ports. From what I can see, we don't support that feature, and the kernel restricts the egress packet size to the MTU. In any case, if we were to attempt to transmit an oversized packet, we have no support in the kernel to deal with that appearing in the port's receive queue. So, this patch attempts to solve the issue by clearing the MVPP2_CLS_SWFWD_PCTRL_MASK() bit, allowing MVPP22_CLS_C2_ATTR0_QHIGH() from the classifier to define the queue-high field of the queue number. My testing seems to confirm my findings above - clearing this bit means that if I enable rxhash on eth2, the interface can then pass traffic, as we are now directing traffic to RX queue 1 rather than queue 33. Traffic still seems to work with rxhash off as well. Reported-by: Matteo Croce <mcr...@redhat.com> Tested-by: Matteo Croce <mcr...@redhat.com> Fixes: 895586d5dc32 ("net: mvpp2: cls: Use RSS contexts to handle RSS tables") Signed-off-by: Russell King <rmk+ker...@armlinux.org.uk> Signed-off-by: David S. Miller <da...@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gre...@linuxfoundation.org> --- drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c index 4344a59c823f..6122057d60c0 100644 --- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c +++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_cls.c @@ -1070,7 +1070,7 @@ void mvpp2_cls_oversize_rxq_set(struct mvpp2_port *port) (port->first_rxq >> MVPP2_CLS_OVERSIZE_RXQ_LOW_BITS)); val = mvpp2_read(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG); - val |= MVPP2_CLS_SWFWD_PCTRL_MASK(port->id); + val &= ~MVPP2_CLS_SWFWD_PCTRL_MASK(port->id); mvpp2_write(port->priv, MVPP2_CLS_SWFWD_PCTRL_REG, val); } -- 2.25.1