On 6/10/2020 12:15 PM, Jonathan McDowell wrote:
> This patch improves the handling of the SGMII interface on the QCA8K
> devices. Previously the driver did no configuration of the port, even if
> it was selected. We now configure it up in the appropriate
> PHY/MAC/Base-X mode depending on what phylink tells us we are connected
> to and ensure it is enabled.
>
> Tested with a device where the CPU connection is RGMII (i.e. the common
> current use case) + one where the CPU connection is SGMII. I don't have
> any devices where the SGMII interface is brought out to something other
> than the CPU.
>
> Signed-off-by: Jonathan McDowell <nood...@earth.li>
> ---
> drivers/net/dsa/qca8k.c | 28 +++++++++++++++++++++++++++-
> drivers/net/dsa/qca8k.h | 13 +++++++++++++
> 2 files changed, 40 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/dsa/qca8k.c b/drivers/net/dsa/qca8k.c
> index dcd9e8fa99b6..33e62598289e 100644
> --- a/drivers/net/dsa/qca8k.c
> +++ b/drivers/net/dsa/qca8k.c
> @@ -681,7 +681,7 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port,
> unsigned int mode,
> const struct phylink_link_state *state)
> {
> struct qca8k_priv *priv = ds->priv;
> - u32 reg;
> + u32 reg, val;
>
> switch (port) {
> case 0: /* 1st CPU port */
> @@ -740,6 +740,32 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int
> port, unsigned int mode,
> case PHY_INTERFACE_MODE_1000BASEX:
> /* Enable SGMII on the port */
> qca8k_write(priv, reg, QCA8K_PORT_PAD_SGMII_EN);
> +
> + /* Enable/disable SerDes auto-negotiation as necessary */
> + val = qca8k_read(priv, QCA8K_REG_PWS);
> + if (phylink_autoneg_inband(mode))
> + val &= ~QCA8K_PWS_SERDES_AEN_DIS;
> + else
> + val |= QCA8K_PWS_SERDES_AEN_DIS;
> + qca8k_write(priv, QCA8K_REG_PWS, val);
> +
> + /* Configure the SGMII parameters */
> + val = qca8k_read(priv, QCA8K_REG_SGMII_CTRL);
> +
> + val |= QCA8K_SGMII_EN_PLL | QCA8K_SGMII_EN_RX |
> + QCA8K_SGMII_EN_TX | QCA8K_SGMII_EN_SD;
> +
> + val &= ~QCA8K_SGMII_MODE_CTRL_MASK;
> + if (dsa_is_cpu_port(ds, port)) {
> + /* CPU port, we're talking to the CPU MAC, be a PHY */
> + val |= QCA8K_SGMII_MODE_CTRL_PHY;
Since port 6 can be interfaced to an external PHY, do not you have to
differentiate here whether this port is connected to an actual PHY,
versus connected to a MAC? You should be able to use mode == MLO_AN_PHY
to differentiate that case from the others.
> + } else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
> + val |= QCA8K_SGMII_MODE_CTRL_MAC;
> + } else {
> + val |= QCA8K_SGMII_MODE_CTRL_BASEX;
Better make this explicit and check for PHY_INTERFACE_MODE_1000BASEX,
even if those are the only two possible values covered by this part of
the case statement.
--
Florian
