On 7/21/20 8:53 PM, Marcin Sloniewski wrote:
> Add support for Seeed Studio's stm32mp157c odyssey board.
> Board consists of SoM with stm32mp157c with 4GB eMMC and 512 MB DDR3 RAM
> and carrier board with USB and ETH interfaces, SD card connector,
> wifi and BT chip AP6236.
>
> In this patch only basic kernel boot is supported and interfacing
> SD card and on-board eMMC.
>
> Signed-off-by: Marcin Sloniewski <marcin.sloniew...@gmail.com>
> ---
>
> Changes in v3:
> - fix compilation on tip of stm32-next
> due to change in names for pinctrl
> - fix deprecated binding for led node
> - fix redundant "okay" statuses
> - add phy part number for eth in comment
You didn't address all my feedback on v2.
> Changes in v2:
> - add new odyssey dts to Makefile
>
> arch/arm/boot/dts/Makefile | 3 +-
> .../arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 276 ++++++++++++++++++
> arch/arm/boot/dts/stm32mp157c-odyssey.dts | 72 +++++
> 3 files changed, 350 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> create mode 100644 arch/arm/boot/dts/stm32mp157c-odyssey.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e6a1cac0bfc7..a3ea2301c82c 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1047,7 +1047,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
> stm32mp157c-dk2.dtb \
> stm32mp157c-ed1.dtb \
> stm32mp157c-ev1.dtb \
> - stm32mp157c-lxa-mc1.dtb
> + stm32mp157c-lxa-mc1.dtb \
> + stm32mp157c-odyssey.dtb
> dtb-$(CONFIG_MACH_SUN4I) += \
> sun4i-a10-a1000.dtb \
> sun4i-a10-ba10-tvbox.dtb \
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> new file mode 100644
> index 000000000000..935632caddd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
> @@ -0,0 +1,276 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniew...@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157.dtsi"
> +#include "stm32mp15xc.dtsi"
> +#include "stm32mp15-pinctrl.dtsi"
> +#include "stm32mp15xxac-pinctrl.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/mfd/st,stpmic1.h>
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C SOM";
> + compatible = "seeed,stm32mp157c-odyssey-som", "st,stm32mp157";
> +
> + memory@c0000000 {
> + device_type = "memory";
> + reg = <0xc0000000 0x20000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + mcuram2: mcuram2@10000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10000000 0x40000>;
> + no-map;
> + };
> +
> + vdev0vring0: vdev0vring0@10040000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10040000 0x1000>;
> + no-map;
> + };
> +
> + vdev0vring1: vdev0vring1@10041000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10041000 0x1000>;
> + no-map;
> + };
> +
> + vdev0buffer: vdev0buffer@10042000 {
> + compatible = "shared-dma-pool";
> + reg = <0x10042000 0x4000>;
> + no-map;
> + };
> +
> + mcuram: mcuram@30000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x30000000 0x40000>;
> + no-map;
> + };
> +
> + retram: retram@38000000 {
> + compatible = "shared-dma-pool";
> + reg = <0x38000000 0x10000>;
> + no-map;
> + };
> +
> + gpu_reserved: gpu@d4000000 {
> + reg = <0xd4000000 0x4000000>;
> + no-map;
> + };
> + };
> +
> + led {
> + compatible = "gpio-leds";
> + led-blue {
> + color = <LED_COLOR_ID_BLUE>;
> + function = LED_FUNCTION_HEARTBEAT;
> + gpios = <&gpiog 3 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> +
> +&gpu {
> + contiguous-area = <&gpu_reserved>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins_a>;
> + i2c-scl-rising-time-ns = <185>;
> + i2c-scl-falling-time-ns = <20>;
> + status = "okay";
> + /* spare dmas for other usage */
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +
> + pmic: stpmic@33 {
> + compatible = "st,stpmic1";
> + reg = <0x33>;
> + interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + regulators {
> + compatible = "st,stpmic1-regulators";
> + ldo1-supply = <&v3v3>;
> + ldo3-supply = <&vdd_ddr>;
> + ldo6-supply = <&v3v3>;
> + pwr_sw1-supply = <&bst_out>;
> + pwr_sw2-supply = <&bst_out>;
> +
> + vddcore: buck1 {
> + regulator-name = "vddcore";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd_ddr: buck2 {
> + regulator-name = "vdd_ddr";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-always-on;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + vdd: buck3 {
> + regulator-name = "vdd";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + st,mask-reset;
> + regulator-initial-mode = <0>;
> + regulator-over-current-protection;
> + };
> +
> + v3v3: buck4 {
> + regulator-name = "v3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + regulator-initial-mode = <0>;
> + };
> +
> + v1v8_audio: ldo1 {
> + regulator-name = "v1v8_audio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO1 0>;
> + };
> +
> + v3v3_hdmi: ldo2 {
> + regulator-name = "v3v3_hdmi";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO2 0>;
> + };
> +
> + vtt_ddr: ldo3 {
> + regulator-name = "vtt_ddr";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <750000>;
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + vdd_usb: ldo4 {
> + regulator-name = "vdd_usb";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + interrupts = <IT_CURLIM_LDO4 0>;
> + };
> +
> + vdda: ldo5 {
> + regulator-name = "vdda";
> + regulator-min-microvolt = <2900000>;
> + regulator-max-microvolt = <2900000>;
> + interrupts = <IT_CURLIM_LDO5 0>;
> + regulator-boot-on;
> + };
> +
> + v1v2_hdmi: ldo6 {
> + regulator-name = "v1v2_hdmi";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + interrupts = <IT_CURLIM_LDO6 0>;
> + };
> +
> + vref_ddr: vref_ddr {
> + regulator-name = "vref_ddr";
> + regulator-always-on;
> + regulator-over-current-protection;
> + };
> +
> + bst_out: boost {
> + regulator-name = "bst_out";
> + interrupts = <IT_OCP_BOOST 0>;
> + };
> +
> + vbus_otg: pwr_sw1 {
> + regulator-name = "vbus_otg";
> + interrupts = <IT_OCP_OTG 0>;
> + };
> +
> + vbus_sw: pwr_sw2 {
> + regulator-name = "vbus_sw";
> + interrupts = <IT_OCP_SWOUT 0>;
> + regulator-active-discharge;
> + };
> + };
> +
> + onkey {
> + compatible = "st,stpmic1-onkey";
> + interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
> + interrupt-names = "onkey-falling", "onkey-rising";
> + power-off-time-sec = <10>;
> + };
> +
> + watchdog {
> + compatible = "st,stpmic1-wdt";
> + status = "disabled";
> + };
> + };
> +};
> +
> +&ipcc {
> + status = "okay";
> +};
> +
> +&iwdg2 {
> + timeout-sec = <32>;
> + status = "okay";
> +};
> +
> +&m4_rproc {
> + memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
> + <&vdev0vring1>, <&vdev0buffer>;
> + mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
> + mbox-names = "vq0", "vq1", "shutdown";
> + interrupt-parent = <&exti>;
> + interrupts = <68 1>;
> + status = "okay";
> +};
> +
> +&rng1 {
> + status = "okay";
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> +
> +&sdmmc2 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + vqmmc-supply = <&v3v3>;
> + mmc-ddr-3_3v;
> + status = "okay";
> +};
> +
> diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> new file mode 100644
> index 000000000000..09edf6afa155
> --- /dev/null
> +++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
> +/*
> + * Copyright (C) 2020 Marcin Sloniewski <marcin.sloniew...@gmail.com>.
> + */
> +
> +/dts-v1/;
> +
> +#include "stm32mp157c-odyssey-som.dtsi"
> +
> +/ {
> + model = "Seeed Studio Odyssey-STM32MP157C Board";
> + compatible = "seeed,stm32mp157c-odyssey", "st,stm32mp157";
> +
> + aliases {
> + ethernet0 = ðernet0;
> + serial0 = &uart4;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +};
> +
> +ðernet0 {
> + status = "okay";
> + pinctrl-0 = <ðernet0_rgmii_pins_a>;
> + pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>;
> + pinctrl-names = "default", "sleep";
> + phy-mode = "rgmii-id";
> + max-speed = <1000>;
> + phy-handle = <&phy0>;
> +
> + mdio0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "snps,dwmac-mdio";
> + phy0: ethernet-phy@0 { /* KSZ9031RN */
> + reg = <0>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&i2c1_pins_a>;
> + pinctrl-1 = <&i2c1_sleep_pins_a>;
> + i2c-scl-rising-time-ns = <100>;
> + i2c-scl-falling-time-ns = <7>;
> + status = "okay";
> + /delete-property/dmas;
> + /delete-property/dma-names;
> +};
> +
> +&sdmmc1 {
> + pinctrl-names = "default", "opendrain", "sleep";
> + pinctrl-0 = <&sdmmc1_b4_pins_a>;
> + pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
> + pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
> + cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
> + disable-wp;
> + st,neg-edge;
> + bus-width = <4>;
> + vmmc-supply = <&v3v3>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins_a>;
> + status = "okay";
> +};
> +
>
--
Pengutronix e.K. | |
Steuerwalder Str. 21 | http://www.pengutronix.de/ |
31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
