No functional changes.
A prepatory step towards full unification.
Signed-off-by: Sam Ravnborg <[EMAIL PROTECTED]>
---
arch/x86/Kconfig.i386 | 124 +++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 124 insertions(+), 0 deletions(-)
diff --git a/arch/x86/Kconfig.i386 b/arch/x86/Kconfig.i386
index af72240..890c258 100644
--- a/arch/x86/Kconfig.i386
+++ b/arch/x86/Kconfig.i386
@@ -218,6 +218,14 @@ config X86_ES7000
Only choose this option if you have such a system, otherwise you
should say N here.
+config X86_VSMP
+ bool "Support for ScaleMP vSMP"
+ depends on X86_64 && PCI
+ help
+ Support for ScaleMP vSMP systems. Say 'Y' here if this kernel is
+ supposed to run on these EM64T-based machines. Only choose this
option
+ if you have one of these machines.
+
endchoice
config SCHED_NO_NO_OMIT_FRAME_POINTER
@@ -313,6 +321,54 @@ config HPET_EMULATE_RTC
depends on HPET_TIMER && RTC=y
default y
+# Mark as embedded because too many people got it wrong.
+# The code disables itself when not needed.
+config GART_IOMMU
+ bool "GART IOMMU support" if EMBEDDED
+ default y
+ select SWIOTLB
+ select AGP
+ depends on X86_64 && PCI
+ help
+ Support for full DMA access of devices with 32bit memory access only
+ on systems with more than 3GB. This is usually needed for USB,
+ sound, many IDE/SATA chipsets and some other devices.
+ Provides a driver for the AMD Athlon64/Opteron/Turion/Sempron GART
+ based hardware IOMMU and a software bounce buffer based IOMMU used
+ on Intel systems and as fallback.
+ The code is only active when needed (enough memory and limited
+ device) unless CONFIG_IOMMU_DEBUG or iommu=force is specified
+ too.
+
+config CALGARY_IOMMU
+ bool "IBM Calgary IOMMU support"
+ select SWIOTLB
+ depends on X86_64 && PCI && EXPERIMENTAL
+ help
+ Support for hardware IOMMUs in IBM's xSeries x366 and x460
+ systems. Needed to run systems with more than 3GB of memory
+ properly with 32-bit PCI devices that do not support DAC
+ (Double Address Cycle). Calgary also supports bus level
+ isolation, where all DMAs pass through the IOMMU. This
+ prevents them from going anywhere except their intended
+ destination. This catches hard-to-find kernel bugs and
+ mis-behaving drivers and devices that do not use the DMA-API
+ properly to set up their DMA buffers. The IOMMU can be
+ turned off at boot time with the iommu=off parameter.
+ Normally the kernel will make the right choice by itself.
+ If unsure, say Y.
+
+config CALGARY_IOMMU_ENABLED_BY_DEFAULT
+ bool "Should Calgary be enabled by default?"
+ default y
+ depends on CALGARY_IOMMU
+ help
+ Should Calgary be enabled by default? if you choose 'y', Calgary
+ will be used (if it exists). If you choose 'n', Calgary will not be
+ used even if it exists. If you choose 'n' and would like to use
+ Calgary anyway, pass 'iommu=calgary' on the kernel command line.
+ If unsure, say Y.
+
config NR_CPUS
int "Maximum number of CPUs (2-255)"
range 2 255
@@ -424,6 +480,22 @@ config X86_MCE_P4THERMAL
Enabling this feature will cause a message to be printed when the P4
enters thermal throttling.
+config X86_MCE_INTEL
+ bool "Intel MCE features"
+ depends on X86_64 && X86_MCE && X86_LOCAL_APIC
+ default y
+ help
+ Additional support for intel specific MCE features such as
+ the thermal monitor.
+
+config X86_MCE_AMD
+ bool "AMD MCE features"
+ depends on X86_64 && X86_MCE && X86_LOCAL_APIC
+ default y
+ help
+ Additional support for AMD specific MCE features such as
+ the DRAM Error Threshold.
+
config VM86
bool "Enable VM86 support" if EMBEDDED
default y
@@ -661,6 +733,34 @@ config NUMA
comment "NUMA (Summit) requires SMP, 64GB highmem support, ACPI"
depends on X86_32 && X86_SUMMIT && (!HIGHMEM64G || !ACPI)
+config K8_NUMA
+ bool "Old style AMD Opteron NUMA detection"
+ depends on X86_64 && NUMA && PCI
+ default y
+ help
+ Enable K8 NUMA node topology detection. You should say Y here if
+ you have a multi processor AMD K8 system. This uses an old
+ method to read the NUMA configuration directly from the builtin
+ Northbridge of Opteron. It is recommended to use X86_64_ACPI_NUMA
+ instead, which also takes priority if both are compiled in.
+
+# Dummy CONFIG option to select ACPI_NUMA from drivers/acpi/Kconfig.
+config X86_64_ACPI_NUMA
+ bool "ACPI NUMA detection"
+ depends on X86_64 && NUMA && ACPI && PCI
+ select ACPI_NUMA
+ default y
+ help
+ Enable ACPI SRAT based node topology detection.
+
+config NUMA_EMU
+ bool "NUMA emulation"
+ depends on X86_64 && NUMA
+ help
+ Enable NUMA emulation. A flat machine will be split
+ into virtual nodes when booted with "numa=fake=N", where N is the
+ number of nodes. This is only useful for debugging.
+
config NODES_SHIFT
int
default "4" if X86_NUMAQ
@@ -832,6 +932,30 @@ config SECCOMP
If unsure, say Y. Only embedded should say N here.
+config CC_STACKPROTECTOR
+ bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
+ depends on X86_64 && EXPERIMENTAL
+ help
+ This option turns on the -fstack-protector GCC feature. This
+ feature puts, at the beginning of critical functions, a canary
+ value on the stack just before the return address, and validates
+ the value just before actually returning. Stack based buffer
+ overflows (that need to overwrite this return address) now also
+ overwrite the canary, which gets detected and the attack is then
+ neutralized via a kernel panic.
+
+ This feature requires gcc version 4.2 or above, or a distribution
+ gcc with the feature backported. Older versions are automatically
+ detected and for those versions, this configuration option is ignored.
+
+config CC_STACKPROTECTOR_ALL
+ bool "Use stack-protector for all functions"
+ depends on CC_STACKPROTECTOR
+ help
+ Normally, GCC only inserts the canary value protection for
+ functions that use large-ish on-stack buffers. By enabling
+ this option, GCC will be asked to do this for ALL functions.
+
source kernel/Kconfig.hz
config KEXEC
--
1.5.3.4.1157.g0e74-dirty
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
