Hi Alex,
On 18/06/2020 17:32, Kieran Bingham wrote:
> Hi Alex,
>
> On 02/04/2020 19:35, Alex Riesen wrote:
>> As all known variants of the Salvator board have the HDMI decoder
>> chip (the ADV7482) connected to the SSI4 on R-Car SoC, the ADV7482
>> endpoint and the connection definitions are placed in the common board
>> file.
>>
>> For the same reason, the CLK_C clock line and I2C configuration (similar
>> to the ak4613, on the same interface) are added into the common file.
>>
>> Signed-off-by: Alexander Riesen <alexander.rie...@cetitec.com>
>>
>> --
>>
>> v5: Add dummy ssi4 node to the rcar sound card in r8a77961, as the
>> devices (Salvator-X 2nd version with R-Car M3 W+) also reference
>> salvator-common.dtsi.
>> Suggested-by: Geert Uytterhoeven <ge...@linux-m68k.org>
>>
>> v2: Also add ssi4_ctrl pin group in the sound pins. The pins are
>> responsible for SCK4 (sample clock) WS4 and (word boundary input),
>> and are required for SSI audio input over I2S.
>>
>> The adv748x shall provide its own implementation of the output clock
>> (MCLK), connected to the audio_clk_c line of the R-Car SoC.
>>
>> If the frequency of the ADV748x MCLK were fixed, the clock
>> implementation were not necessary, but it does not seem so: the MCLK
>> depends on the value in a speed multiplier register and the input sample
>> rate (48kHz).
>>
>> Remove audio clock C from the clocks of adv7482.
>>
>> The clocks property of the video-receiver node lists the input
>> clocks of the device, which is quite the opposite from the
>> original intention: the adv7482 on Salvator X boards is a
>> provide of the MCLK clock for I2S audio output.
>>
>> Remove old definition of &sound_card.dais and reduce size of changes
>> in the Salvator-X specific device tree source.
>>
>> Declare video-receiver a clock producer, as the adv748x driver
>> implements the master clock used I2S audio output.
>>
>> Suggested-by: Geert Uytterhoeven <ge...@linux-m68k.org>
>>
>> v2: The driver provides only MCLK clock, not the SCLK and LRCLK,
>> which are part of the I2S protocol.
>>
>> Suggested-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
>> ---
>> .../boot/dts/renesas/r8a77950-salvator-x.dts | 3 +-
>> arch/arm64/boot/dts/renesas/r8a77961.dtsi | 1 +
>> .../boot/dts/renesas/salvator-common.dtsi | 47 +++++++++++++++++--
Once again I'm back trying to test this series, and one issue I've had
is that the board I have (r8a77951-salvator-xs.dts) isn't included in
this DT update.
For v6, Should we include the relevant changes to all the following?
arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77951-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77960-salvator-x.dts
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts
arch/arm64/boot/dts/renesas/salvator-x.dtsi
And perhaps handle the salvator-xs in a second (yet very similar) patch?
arch/arm64/boot/dts/renesas/r8a77951-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77960-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77961-salvator-xs.dts
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts
arch/arm64/boot/dts/renesas/salvator-xs.dtsi
I think I've added the relevant entries to my dtb, but I haven't
successfully captured audio yet.
I can see the device being listed through arecord:
kbingham@salvator-xs:~$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: rcarsound [rcar-sound], device 0: rsnd-dai.0-ak4613-hifi
ak4613-hifi-0 []
Subdevices: 0/1
Subdevice #0: subdevice #0
card 0: rcarsound [rcar-sound], device 3: rsnd-dai.3-adv748x-i2s
adv748x.4-0070-3 []
Subdevices: 1/1
Subdevice #0: subdevice #0
But as yet, everything I try to record fails or is empty silence.
Debugging ...
--
Regards
Kieran
>> 3 files changed, 45 insertions(+), 6 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> index 2438825c9b22..e16c146808b6 100644
>> --- a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> +++ b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
>> @@ -146,7 +146,8 @@ &sata {
>> &sound_card {
>> dais = <&rsnd_port0 /* ak4613 */
>> &rsnd_port1 /* HDMI0 */
>> - &rsnd_port2>; /* HDMI1 */
>> + &rsnd_port2 /* HDMI1 */
>> + &rsnd_port3>; /* adv7482 hdmi-in */
>
> Ah - that was confusing at first... but HDMI0 and HDMI1 are *outputs*,
> where of course the adv7482 is an input ;-)
>
>
> Otherwise, I can't spot anything else yet so:
>
> Reviewed-by: Kieran Bingham <kieran.bingham+rene...@ideasonboard.com>
>
> But I fear there may have been some churn around here, so it would be
> good to see a rebase too.
>
> --
> Kieran
>
>
>
>> };
>>
>> &usb2_phy2 {
>> diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> index be3824bda632..b79907beaf31 100644
>> --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
>> @@ -861,6 +861,7 @@ rcar_sound,src {
>> rcar_sound,ssi {
>> ssi0: ssi-0 { };
>> ssi1: ssi-1 { };
>> + ssi4: ssi-4 { };
>> };
>> };
>>
>> diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> index 98bbcafc8c0d..ead7f8d7a929 100644
>> --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
>> @@ -460,7 +460,7 @@ pca9654: gpio@20 {
>> #gpio-cells = <2>;
>> };
>>
>> - video-receiver@70 {
>> + adv7482_hdmi_in: video-receiver@70 {
>> compatible = "adi,adv7482";
>> reg = <0x70 0x71 0x72 0x73 0x74 0x75
>> 0x60 0x61 0x62 0x63 0x64 0x65>;
>> @@ -469,6 +469,7 @@ video-receiver@70 {
>>
>> #address-cells = <1>;
>> #size-cells = <0>;
>> + #clock-cells = <0>; /* the MCLK for I2S output */
>>
>> interrupt-parent = <&gpio6>;
>> interrupt-names = "intrq1", "intrq2";
>> @@ -510,6 +511,15 @@ adv7482_txb: endpoint {
>> remote-endpoint = <&csi20_in>;
>> };
>> };
>> +
>> + port@c {
>> + reg = <12>;
>> +
>> + adv7482_i2s: endpoint {
>> + remote-endpoint = <&rsnd_endpoint3>;
>> + system-clock-direction-out;
>> + };
>> + };
>> };
>>
>> csa_vdd: adc@7c {
>> @@ -684,7 +694,8 @@ sdhi3_pins_uhs: sd3_uhs {
>> };
>>
>> sound_pins: sound {
>> - groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
>> + groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
>> + "ssi4_data", "ssi4_ctrl";
>> function = "ssi";
>> };
>>
>> @@ -733,8 +744,8 @@ &rcar_sound {
>> pinctrl-0 = <&sound_pins &sound_clk_pins>;
>> pinctrl-names = "default";
>>
>> - /* Single DAI */
>> - #sound-dai-cells = <0>;
>> + /* multi DAI */
>> + #sound-dai-cells = <1>;
>>
>> /* audio_clkout0/1/2/3 */
>> #clock-cells = <1>;
>> @@ -758,8 +769,19 @@ &rcar_sound {
>> <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
>> <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
>> <&audio_clk_a>, <&cs2000>,
>> - <&audio_clk_c>,
>> + <&adv7482_hdmi_in>,
>> <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
>> + clock-names = "ssi-all",
>> + "ssi.9", "ssi.8", "ssi.7", "ssi.6",
>> + "ssi.5", "ssi.4", "ssi.3", "ssi.2",
>> + "ssi.1", "ssi.0",
>> + "src.9", "src.8", "src.7", "src.6",
>> + "src.5", "src.4", "src.3", "src.2",
>> + "src.1", "src.0",
>> + "mix.1", "mix.0",
>> + "ctu.1", "ctu.0",
>> + "dvc.0", "dvc.1",
>> + "clk_a", "clk_b", "clk_c", "clk_i";
>>
>> ports {
>> #address-cells = <1>;
>> @@ -777,6 +799,21 @@ rsnd_endpoint0: endpoint {
>> capture = <&ssi1 &src1 &dvc1>;
>> };
>> };
>> + rsnd_port3: port@3 {
>> + reg = <3>;
>> + rsnd_endpoint3: endpoint {
>> + remote-endpoint = <&adv7482_i2s>;
>> +
>> + dai-tdm-slot-num = <8>;
>> + dai-tdm-slot-width = <32>;
>> + dai-format = "left_j";
>> + mclk-fs = <256>;
>> + bitclock-master = <&adv7482_i2s>;
>> + frame-master = <&adv7482_i2s>;
>> +
>> + capture = <&ssi4>;
>> + };
>> + };
>> };
>> };
>>
>>
>
--
Regards
--
Kieran
