According to Freescale's documentation, MPC74XX processors have an
erratum that prevents the TAU interrupt from working, so don't try to
use it when running on those processors.
Fixes: 1da177e4c3f41 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <user...@yahoo.com>
Signed-off-by: Finn Thain <fth...@telegraphics.com.au>
---
arch/powerpc/kernel/tau_6xx.c | 33 ++++++++++++++-------------------
arch/powerpc/platforms/Kconfig | 5 ++---
2 files changed, 16 insertions(+), 22 deletions(-)
diff --git a/arch/powerpc/kernel/tau_6xx.c b/arch/powerpc/kernel/tau_6xx.c
index b8d7e7d498e0a..614b5b272d9c6 100644
--- a/arch/powerpc/kernel/tau_6xx.c
+++ b/arch/powerpc/kernel/tau_6xx.c
@@ -40,6 +40,8 @@ static struct tau_temp
unsigned char grew;
} tau[NR_CPUS];
+static bool tau_int_enable;
+
#undef DEBUG
/* TODO: put these in a /proc interface, with some sanity checks, and maybe
@@ -54,22 +56,13 @@ static struct tau_temp
static void set_thresholds(unsigned long cpu)
{
-#ifdef CONFIG_TAU_INT
- /*
- * setup THRM1,
- * threshold, valid bit, enable interrupts, interrupt when below
threshold
- */
- mtspr(SPRN_THRM1, THRM1_THRES(tau[cpu].low) | THRM1_V | THRM1_TIE |
THRM1_TID);
+ u32 maybe_tie = tau_int_enable ? THRM1_TIE : 0;
- /* setup THRM2,
- * threshold, valid bit, enable interrupts, interrupt when above
threshold
- */
- mtspr (SPRN_THRM2, THRM1_THRES(tau[cpu].high) | THRM1_V | THRM1_TIE);
-#else
- /* same thing but don't enable interrupts */
- mtspr(SPRN_THRM1, THRM1_THRES(tau[cpu].low) | THRM1_V | THRM1_TID);
- mtspr(SPRN_THRM2, THRM1_THRES(tau[cpu].high) | THRM1_V);
-#endif
+ /* setup THRM1, threshold, valid bit, interrupt when below threshold */
+ mtspr(SPRN_THRM1, THRM1_THRES(tau[cpu].low) | THRM1_V | maybe_tie |
THRM1_TID);
+
+ /* setup THRM2, threshold, valid bit, interrupt when above threshold */
+ mtspr(SPRN_THRM2, THRM1_THRES(tau[cpu].high) | THRM1_V | maybe_tie);
}
static void TAUupdate(int cpu)
@@ -142,9 +135,8 @@ static void tau_timeout(void * info)
local_irq_save(flags);
cpu = smp_processor_id();
-#ifndef CONFIG_TAU_INT
- TAUupdate(cpu);
-#endif
+ if (!tau_int_enable)
+ TAUupdate(cpu);
size = tau[cpu].high - tau[cpu].low;
if (size > min_window && ! tau[cpu].grew) {
@@ -225,6 +217,9 @@ static int __init TAU_init(void)
return 1;
}
+ tau_int_enable = IS_ENABLED(CONFIG_TAU_INT) &&
+ !strcmp(cur_cpu_spec->platform, "ppc750");
+
tau_workq = alloc_workqueue("tau", WQ_UNBOUND, 1, 0);
if (!tau_workq)
return -ENOMEM;
@@ -234,7 +229,7 @@ static int __init TAU_init(void)
queue_work(tau_workq, &tau_work);
pr_info("Thermal assist unit using %s, shrink_timer: %d ms\n",
- IS_ENABLED(CONFIG_TAU_INT) ? "interrupts" : "workqueue",
shrink_timer);
+ tau_int_enable ? "interrupts" : "workqueue", shrink_timer);
tau_initialized = 1;
return 0;
diff --git a/arch/powerpc/platforms/Kconfig b/arch/powerpc/platforms/Kconfig
index fb7515b4fa9c6..9fe36f0b54c1a 100644
--- a/arch/powerpc/platforms/Kconfig
+++ b/arch/powerpc/platforms/Kconfig
@@ -223,9 +223,8 @@ config TAU
temperature within 2-4 degrees Celsius. This option shows the current
on-die temperature in /proc/cpuinfo if the cpu supports it.
- Unfortunately, on some chip revisions, this sensor is very inaccurate
- and in many cases, does not work at all, so don't assume the cpu
- temp is actually what /proc/cpuinfo says it is.
+ Unfortunately, this sensor is very inaccurate when uncalibrated, so
+ don't assume the cpu temp is actually what /proc/cpuinfo says it is.
config TAU_INT
bool "Interrupt driven TAU driver (DANGEROUS)"
--
2.26.2
