Hi Rocky,
> This patch add support for WCN6855 i.e. patch and nvm download
> support.
>
> Signed-off-by: Rocky Liao <rjl...@codeaurora.org>
> ---
> drivers/bluetooth/btusb.c | 42 +++++++++++++++++++++++++++++++++++----
> 1 file changed, 38 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index fe80588c7bd3..e51e754ca9b8 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -59,6 +59,7 @@ static struct usb_driver btusb_driver;
> #define BTUSB_MEDIATEK 0x200000
> #define BTUSB_WIDEBAND_SPEECH 0x400000
> #define BTUSB_VALID_LE_STATES 0x800000
> +#define BTUSB_QCA_WCN6855 0x1000000
>
> static const struct usb_device_id btusb_table[] = {
> /* Generic Bluetooth USB device */
> @@ -273,6 +274,10 @@ static const struct usb_device_id blacklist_table[] = {
> { USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME },
> { USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME },
>
> + /* QCA WCN6855 chipset */
> + { USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 |
> + BTUSB_WIDEBAND_SPEECH },
> +
> /* Broadcom BCM2035 */
> { USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
> { USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
> @@ -3391,6 +3396,26 @@ static int btusb_set_bdaddr_ath3012(struct hci_dev
> *hdev,
> return 0;
> }
>
> +static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev,
> + const bdaddr_t *bdaddr)
> +{
> + struct sk_buff *skb;
> + u8 buf[6];
> + long ret;
> +
> + memcpy(buf, bdaddr, sizeof(bdaddr_t));
> +
> + skb = __hci_cmd_sync(hdev, 0xfc14, sizeof(buf), buf, HCI_INIT_TIMEOUT);
> + if (IS_ERR(skb)) {
> + ret = PTR_ERR(skb);
> + bt_dev_err(hdev, "Change address command failed (%ld)", ret);
> + return ret;
> + }
> + kfree_skb(skb);
> +
> + return 0;
> +}
What is wrong with using qca_set_bdaddr() function.
> +
> #define QCA_DFU_PACKET_LEN 4096
>
> #define QCA_GET_TARGET_VERSION 0x09
> @@ -3428,6 +3453,8 @@ static const struct qca_device_info qca_devices_table[]
> = {
> { 0x00000201, 28, 4, 18 }, /* Rome 2.1 */
> { 0x00000300, 28, 4, 18 }, /* Rome 3.0 */
> { 0x00000302, 28, 4, 18 }, /* Rome 3.2 */
> + { 0x00130100, 40, 4, 18 }, /* WCN6855 1.0 */
> + { 0x00130200, 40, 4, 18 } /* WCN6855 2.0 */
> };
>
> static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
> @@ -3530,7 +3557,7 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev
> *hdev,
> struct qca_rampatch_version *rver;
> const struct firmware *fw;
> u32 ver_rom, ver_patch;
> - u16 rver_rom, rver_patch;
> + u32 rver_rom, rver_patch;
> char fwname[64];
> int err;
>
> @@ -3552,6 +3579,9 @@ static int btusb_setup_qca_load_rampatch(struct hci_dev
> *hdev,
> rver_rom = le16_to_cpu(rver->rom_version);
> rver_patch = le16_to_cpu(rver->patch_version);
>
> + if (ver_rom & ~0xffffU)
> + rver_rom = *(u16 *)(fw->data + 16) << 16 | rver_rom;
> +
You will require proper unaligned access unless you can guarantee things are
aligned properly. And since I assume the firmware data is in a specific endian
format, you need to convert it correctly.
In addition, you change the variables to u32, but still use le16_to_cpu
function above. Something is not adding up. Have you actually run a sparse
check?
> bt_dev_info(hdev, "QCA: patch rome 0x%x build 0x%x, "
> "firmware rome 0x%x build 0x%x",
> rver_rom, rver_patch, ver_rom, ver_patch);
> @@ -3625,9 +3655,6 @@ static int btusb_setup_qca(struct hci_dev *hdev)
> return err;
>
> ver_rom = le32_to_cpu(ver.rom_version);
> - /* Don't care about high ROM versions */
> - if (ver_rom & ~0xffffU)
> - return 0;
>
> for (i = 0; i < ARRAY_SIZE(qca_devices_table); i++) {
> if (ver_rom == qca_devices_table[i].rom_version)
> @@ -4063,6 +4090,13 @@ static int btusb_probe(struct usb_interface *intf,
> btusb_check_needs_reset_resume(intf);
> }
>
> + if (id->driver_info & BTUSB_QCA_WCN6855) {
> + data->setup_on_usb = btusb_setup_qca;
> + hdev->set_bdaddr = btusb_set_bdaddr_wcn6855;
> + hdev->cmd_timeout = btusb_qca_cmd_timeout;
> + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> + }
> +
Regards
Marcel
