Wei Liu <wei....@kernel.org> writes:
> On Tue, Sep 15, 2020 at 01:02:08PM +0200, Vitaly Kuznetsov wrote:
>> Wei Liu <wei....@kernel.org> writes:
>>
>> > On Tue, Sep 15, 2020 at 12:32:29PM +0200, Vitaly Kuznetsov wrote:
>> >> Wei Liu <wei....@kernel.org> writes:
>> >>
>> >> > When Linux is running as the root partition, the hypercall page will
>> >> > have already been setup by Hyper-V. Copy the content over to the
>> >> > allocated page.
>> >>
>> >> And we can't setup a new hypercall page by writing something different
>> >> to HV_X64_MSR_HYPERCALL, right?
>> >>
>> >
>> > My understanding is that we can't, but Sunil can maybe correct me.
>> >
>> >> >
>> >> > The suspend, resume and cleanup paths remain untouched because they are
>> >> > not supported in this setup yet.
>> >> >
>> >> > Signed-off-by: Lillian Grassin-Drake <ligra...@microsoft.com>
>> >> > Signed-off-by: Sunil Muthuswamy <sunil...@microsoft.com>
>> >> > Signed-off-by: Nuno Das Neves <nudas...@microsoft.com>
>> >> > Co-Developed-by: Lillian Grassin-Drake <ligra...@microsoft.com>
>> >> > Co-Developed-by: Sunil Muthuswamy <sunil...@microsoft.com>
>> >> > Co-Developed-by: Nuno Das Neves <nudas...@microsoft.com>
>> >> > Signed-off-by: Wei Liu <wei....@kernel.org>
>> >> > ---
>> >> > arch/x86/hyperv/hv_init.c | 26 ++++++++++++++++++++++++--
>> >> > 1 file changed, 24 insertions(+), 2 deletions(-)
>> >> >
>> >> > diff --git a/arch/x86/hyperv/hv_init.c b/arch/x86/hyperv/hv_init.c
>> >> > index 0eec1ed32023..26233aebc86c 100644
>> >> > --- a/arch/x86/hyperv/hv_init.c
>> >> > +++ b/arch/x86/hyperv/hv_init.c
>> >> > @@ -25,6 +25,7 @@
>> >> > #include <linux/cpuhotplug.h>
>> >> > #include <linux/syscore_ops.h>
>> >> > #include <clocksource/hyperv_timer.h>
>> >> > +#include <linux/highmem.h>
>> >> >
>> >> > /* Is Linux running as the root partition? */
>> >> > bool hv_root_partition;
>> >> > @@ -448,8 +449,29 @@ void __init hyperv_init(void)
>> >> >
>> >> > rdmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64);
>> >> > hypercall_msr.enable = 1;
>> >> > - hypercall_msr.guest_physical_address =
>> >> > vmalloc_to_pfn(hv_hypercall_pg);
>> >> > - wrmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64);
>> >> > +
>> >> > + if (hv_root_partition) {
>> >> > + struct page *pg;
>> >> > + void *src, *dst;
>> >> > +
>> >> > + /*
>> >> > + * Order is important here. We must enable the
>> >> > hypercall page
>> >> > + * so it is populated with code, then copy the code to
>> >> > an
>> >> > + * executable page.
>> >> > + */
>> >> > + wrmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64);
>> >> > +
>> >> > + pg = vmalloc_to_page(hv_hypercall_pg);
>> >> > + dst = kmap(pg);
>> >> > + src = memremap(hypercall_msr.guest_physical_address <<
>> >> > PAGE_SHIFT, PAGE_SIZE,
>> >> > + MEMREMAP_WB);
>> >>
>> >> memremap() can fail...
>> >
>> > And we don't care here, if it fails, we would rather it panic or oops.
>> >
>> > I was relying on the fact that copying from / to a NULL pointer will
>> > cause the kernel to crash. But of course it wouldn't hurt to explicitly
>> > panic here.
>> >
>> >>
>> >> > + memcpy(dst, src, PAGE_SIZE);
>> >> > + memunmap(src);
>> >> > + kunmap(pg);
>> >> > + } else {
>> >> > + hypercall_msr.guest_physical_address =
>> >> > vmalloc_to_pfn(hv_hypercall_pg);
>> >> > + wrmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64);
>> >> > + }
>> >>
>> >> Why can't we do wrmsrl() for both cases here?
>> >>
>> >
>> > Because the hypercall page has already been set up when Linux is the
>> > root.
>>
>> But you already do wrmsrl(HV_X64_MSR_HYPERCALL, hypercall_msr.as_uint64)
>> in 'if (hv_root_partition)' case above, that's why I asked.
>>
>
> You mean extracting wrmsrl to this point? The ordering matters. See the
> comment in the root branch -- we have to enable the page before copying
> the content.
>
> What can be done is:
>
> if (!root) {
> /* some stuff */
> }
>
> wrmsrl(...)
>
> if (root) {
> /* some stuff */
> }
>
> This is not looking any better than the existing code.
>
Oh, I missed the comment indeed. So Hypervisor already picked a page for
us, however, it didn't enable it and it's not populated? How can we be
sure that we didn't use it for something else already? Maybe we can
still give a different known-to-be-empty page?
--
Vitaly
