Switchdev drivers often have different VLAN semantics than the bridge. For example, consider this:
ip link add br0 type bridge ip link set swp0 master br0 bridge mdb add dev br0 port swp0 grp 01:02:03:04:05:06 permanent ip link del br0 [ 26.085816] mscc_felix 0000:00:00.5 swp0: failed (err=-2) to del object (id=2) This is because the mscc_ocelot driver, when VLAN awareness is disabled, classifies all traffic to the port-based VLAN (pvid). The pvid is 0 when the port is standalone, and it is inherited from the bridge default pvid (which is 1 by default, but it may take other values) when it joins the VLAN-unaware bridge, and then the pvid resets to 0 when the port leaves the bridge again. Now because the mscc_ocelot switch classifies all traffic to its private pvid, it needs to translate between the vid that the mdb comes with, and the vid that will actually be programmed into hardware. The bridge uses the vid of 0 in VLAN-unaware mode, while the hardware uses the pvid inherited from the bridge, that's the difference. So what will happen is: Step 1 (addition): br_mdb_notify(RTM_NEWMDB) -> ocelot_port_mdb_add(mdb->addr=01:02:03:04:05:06, mdb->vid=0) -> mdb->vid is remapped from 0 to 1 and installed into ocelot->multicast Step 2 (removal): del_nbp -> netdev_upper_dev_unlink(dev, br->dev) -> ocelot_port_bridge_leave -> ocelot_port_set_pvid(ocelot, port, 0) -> br_multicast_del_port is called and the switchdev notifier is deferred for some time later -> ocelot_port_mdb_del(mdb->addr=01:02:03:04:05:06, mdb->vid=0) -> mdb->vid is remapped from 0 to 0, the port pvid (!!!) -> the remapped mdb (addr=01:02:03:04:05:06, vid=0) is not found inside the ocelot->multicast list, and -ENOENT is returned So the problem is that mscc_ocelot assumes that the port is removed _after_ the multicast entries have been deleted. And this is not an unreasonable assumption, presumably it isn't the only switchdev that needs to remap the vid. So we can reorder the teardown path in order for that assumption to hold true. Since br_mdb_notify() issues a SWITCHDEV_F_DEFER operation, we must move the call not only before netdev_upper_dev_unlink(), but in fact before switchdev_deferred_process(). Signed-off-by: Vladimir Oltean <vladimir.olt...@nxp.com> --- net/bridge/br_if.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/net/bridge/br_if.c b/net/bridge/br_if.c index a0e9a7937412..cdbeaf203b0b 100644 --- a/net/bridge/br_if.c +++ b/net/bridge/br_if.c @@ -344,6 +344,7 @@ static void del_nbp(struct net_bridge_port *p) nbp_vlan_flush(p); br_fdb_delete_by_port(br, p, 0, 1); + br_multicast_del_port(p); switchdev_deferred_process(); nbp_backup_clear(p); @@ -355,8 +356,6 @@ static void del_nbp(struct net_bridge_port *p) netdev_rx_handler_unregister(dev); - br_multicast_del_port(p); - kobject_uevent(&p->kobj, KOBJ_REMOVE); kobject_del(&p->kobj); -- 2.25.1