On Fri, Oct 16, 2020 at 01:16:18PM +0200, Hans de Goede wrote:
> Hi,
> 
> On 9/22/20 11:19 AM, Jiri Kosina wrote:
> > On Wed, 16 Sep 2020, Sultan Alsawaf wrote:
> > 
> >> From: Sultan Alsawaf <sul...@kerneltoast.com>
> >>
> >> This is a fixed resubmission of "[PATCH 0/2] i2c-hid: Save power by 
> >> reducing i2c
> >> xfers with block reads". That original patchset did not have enough fixes 
> >> for
> >> the designware i2c adapter's I2C_M_RECV_LEN feature, which is documented
> >> extensively in the original email thread.
> >>
> >> Here is the original cover letter, which still applies:
> >> "I noticed on my Dell Precision 15 5540 with an i9-9880H that simply 
> >> putting my
> >> finger on the touchpad would increase my system's power consumption by 4W, 
> >> which
> >> is quite considerable. Resting my finger on the touchpad would generate 
> >> roughly
> >> 4000 i2c irqs per second, or roughly 20 i2c irqs per touchpad irq.
> >>
> >> Upon closer inspection, I noticed that the i2c-hid driver would always 
> >> transfer
> >> the maximum report size over i2c (which is 60 bytes for my touchpad), but 
> >> all of
> >> my touchpad's normal touch events are only 32 bytes long according to the 
> >> length
> >> byte contained in the buffer sequence.
> >>
> >> Therefore, I was able to save about 2W of power by passing the 
> >> I2C_M_RECV_LEN
> >> flag in i2c-hid, which says to look for the payload length in the first 
> >> byte of
> >> the transfer buffer and adjust the i2c transaction accordingly. The only 
> >> problem
> >> though is that my i2c controller's driver allows bytes other than the 
> >> first one
> >> to be used to retrieve the payload length, which is incorrect according to 
> >> the
> >> SMBus spec, and would break my i2c-hid change since not *all* of the 
> >> reports
> >> from my touchpad are conforming SMBus block reads.
> >>
> >> This patchset fixes the I2C_M_RECV_LEN behavior in the designware i2c 
> >> driver and
> >> modifies i2c-hid to use I2C_M_RECV_LEN to save quite a bit of power. Even 
> >> if the
> >> peripheral controlled by i2c-hid doesn't support block reads, the i2c 
> >> controller
> >> drivers should cope with this and proceed with the i2c transfer using the
> >> original requested length."
> >>
> >> Sultan
> >>
> >> Sultan Alsawaf (4):
> >>   i2c: designware: Fix transfer failures for invalid SMBus block reads
> >>   i2c: designware: Ensure tx_buf_len is nonzero for SMBus block reads
> >>   i2c: designware: Allow SMBus block reads up to 255 bytes in length
> >>   HID: i2c-hid: Use block reads when possible to save power
> >>
> >>  drivers/hid/i2c-hid/i2c-hid-core.c         |  5 ++++-
> >>  drivers/i2c/busses/i2c-designware-master.c | 15 +++++++++------
> >>  2 files changed, 13 insertions(+), 7 deletions(-)
> > 
> > Hans, Benjamin, could you please give this patchset some smoke-testing? It 
> > looks good to me, but I'd like it to get some testing from your testing 
> > machinery before merging.
> 
> Sorry for being slow to respond to this. I have not gotten around to testing
> this, but I saw another email that this breaks things on at least AMD
> platforms, so I guess that this is on hold for now ?
> 
> Regards,
> 
> Hans

Hi,

Only the i2c-hid-core.c hunk is on hold. It is on hold until every i2c adapter
gets updated for proper block read functionality up to the new block read limit
of 255 bytes. This is not really a surprise.

The designware patches are good to go. Please let me know what you think of
them.

Sultan

Reply via email to