On Wed, Dec 23, 2020 at 02:23:16PM -0800, Tim Harvey wrote: > The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development > kits comprised of a GW700x SoM and a Baseboard. > > The GW700x SoM contains: > - IMX8MM SoC
It's i.MX 8M Mini. https://www.nxp.com/products/processors-and-microcontrollers/arm-processors/i-mx-applications-processors/i-mx-8-processors/i-mx-8m-mini-arm-cortex-a53-cortex-m4-audio-voice-video:i.MX8MMINI > - LPDDR4 DRAM > - eMMC FLASH > - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) > - GbE PHY connected to the IMX8MM FEC > - Power Management IC > > The GW71xx Baseboard contains: > - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 1x RJ45 GbE (IMX8MM FEC) > - PCIe Clock generator > - GPS and accelerometer > - 1x USB 2.0 Front Panel connector > - wide range power supply > > The GW72xx Baseboard contains: > - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > The GW73xx Baseboard contains: > - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM > - 2x RJ45 GbE (IMX8MM FEC and LAN743x) > - 1x MicroSD connector > - 1x USB 2.0 Front Panel connector > - 1x SPI connector > - WiFi/BT > - PCIe Clock generator > - GPS and accelerometer > - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) > - wide range power supply > > Signed-off-by: Tim Harvey <[email protected]> > --- > arch/arm64/boot/dts/freescale/Makefile | 3 + > .../boot/dts/freescale/imx8mm-venice-gw700x.dtsi | 482 > +++++++++++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 ++++++++ > .../boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 + > .../boot/dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++++ > .../boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 + > .../boot/dts/freescale/imx8mm-venice-gw73xx.dtsi | 363 ++++++++++++++++ > 8 files changed, 1403 insertions(+) > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts > create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi > > diff --git a/arch/arm64/boot/dts/freescale/Makefile > b/arch/arm64/boot/dts/freescale/Makefile > index f8d5943..ecdd233 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -32,6 +32,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb > dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > new file mode 100644 > index 00000000..7e1b96b > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi > @@ -0,0 +1,482 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/linux-event-codes.h> > +#include <dt-bindings/net/ti-dp83867.h> > + > +/ { > + memory@40000000 { > + device_type = "memory"; > + reg = <0x0 0x40000000 0 0x80000000>; > + }; > + > + gpio_keys { > + compatible = "gpio-keys"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + user_pb { > + label = "user_pb"; > + gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>; > + linux,code = <BTN_0>; > + }; > + > + user_pb1x { > + label = "user_pb1x"; > + linux,code = <BTN_1>; > + interrupt-parent = <&gsc>; > + interrupts = <0>; > + }; > + > + key_erased { > + label = "key-erased"; Above you use underscore, here hyphen. Make it consistent. > + linux,code = <BTN_2>; > + interrupt-parent = <&gsc>; > + interrupts = <1>; > + }; > + > + eeprom_wp { > + label = "eeprom_wp"; > + linux,code = <BTN_3>; > + interrupt-parent = <&gsc>; > + interrupts = <2>; > + }; > + > + tamper { > + label = "tamper"; > + linux,code = <BTN_4>; > + interrupt-parent = <&gsc>; > + interrupts = <5>; > + }; > + > + switch_hold { > + label = "switch_hold"; > + linux,code = <BTN_5>; > + interrupt-parent = <&gsc>; > + interrupts = <7>; > + }; > + }; > +}; > + > +&A53_0 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_1 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_2 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&A53_3 { > + cpu-supply = <&buck3_reg>; > +}; > + > +&ddrc { > + operating-points-v2 = <&ddrc_opp_table>; > + > + ddrc_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-25M { > + opp-hz = /bits/ 64 <25000000>; > + }; > + > + opp-100M { > + opp-hz = /bits/ 64 <100000000>; > + }; > + > + opp-750M { > + opp-hz = /bits/ 64 <750000000>; > + }; > + }; > +}; > + > +&fec1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec1>; > + phy-mode = "rgmii-id"; > + phy-handle = <ðphy0>; > + status = "okay"; > + > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy0: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + }; > + }; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + gsc: gsc@20 { Node name should describe class of a device so maybe "system-controller"? > + compatible = "gw,gsc"; > + reg = <0x20>; > + pinctrl-0 = <&pinctrl_gsc>; > + interrupt-parent = <&gpio2>; > + interrupts = <6 GPIO_ACTIVE_LOW>; Wrong flag. > + interrupt-controller; > + #interrupt-cells = <1>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + adc { Just to be sure - did you build it with W=1 to find any dtc warnings? > + compatible = "gw,gsc-adc"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + channel@6 { > + gw,mode = <0>; > + reg = <0x06>; > + label = "temp"; > + }; > + > + channel@8 { > + gw,mode = <1>; > + reg = <0x08>; > + label = "vdd_bat"; > + }; > + > + channel@16 { > + gw,mode = <4>; > + reg = <0x16>; > + label = "fan_tach"; > + }; > + > + channel@82 { > + gw,mode = <2>; > + reg = <0x82>; > + label = "vdd_vin"; > + gw,voltage-divider-ohms = <22100 1000>; > + }; > + > + channel@84 { > + gw,mode = <2>; > + reg = <0x84>; > + label = "vdd_adc1"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@86 { > + gw,mode = <2>; > + reg = <0x86>; > + label = "vdd_adc2"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@88 { > + gw,mode = <2>; > + reg = <0x88>; > + label = "vdd_dram"; > + }; > + > + channel@8c { > + gw,mode = <2>; > + reg = <0x8c>; > + label = "vdd_1p2"; > + }; > + > + channel@8e { > + gw,mode = <2>; > + reg = <0x8e>; > + label = "vdd_1p0"; > + }; > + > + channel@90 { > + gw,mode = <2>; > + reg = <0x90>; > + label = "vdd_2p5"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@92 { > + gw,mode = <2>; > + reg = <0x92>; > + label = "vdd_3p3"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + > + channel@98 { > + gw,mode = <2>; > + reg = <0x98>; > + label = "vdd_0p95"; > + }; > + > + channel@9a { > + gw,mode = <2>; > + reg = <0x9a>; > + label = "vdd_1p8"; > + }; > + > + channel@a2 { > + gw,mode = <2>; > + reg = <0xa2>; > + label = "vdd_gsc"; > + gw,voltage-divider-ohms = <10000 10000>; > + }; > + }; > + > + fan-controller@0 { > + #address-cells = <1>; > + #size-cells = <0>; These do not seem needed. > + compatible = "gw,gsc-fan"; > + reg = <0x0a>; > + }; > + }; > + > + gsc_gpio: pca9555@23 { Lookes like gpio-controller, so "gpio". Please run make dtbs_check to be sure your board validate against dt-schema. > + compatible = "nxp,pca9555"; > + reg = <0x23>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-parent = <&gsc>; > + interrupts = <4>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c02"; > + reg = <0x50>; > + pagesize = <16>; > + }; > + > + eeprom@51 { > + compatible = "atmel,24c02"; > + reg = <0x51>; > + pagesize = <16>; > + }; > + > + eeprom@52 { > + compatible = "atmel,24c32"; > + reg = <0x52>; > + pagesize = <32>; > + }; > + > + eeprom@53 { > + compatible = "atmel,24c32"; > + reg = <0x53>; > + pagesize = <32>; > + }; > + > + pmic@69 { > + compatible = "mps,mp5416"; > + reg = <0x69>; > + > + regulators { > + buck1 { > + regulator-name = "vdd_0p95"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <1000000>; > + regulator-max-microamp = <2500000>; > + regulator-boot-on; > + }; > + > + buck2 { > + regulator-name = "vdd_soc"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <900000>; > + regulator-max-microamp = <1000000>; > + regulator-boot-on; > + }; > + > + buck3_reg: buck3 { > + regulator-name = "vdd_arm"; > + regulator-min-microvolt = <805000>; > + regulator-max-microvolt = <1000000>; > + regulator-max-microamp = <2200000>; > + regulator-boot-on; > + }; > + > + buck4 { > + regulator-name = "vdd_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-max-microamp = <500000>; > + regulator-boot-on; > + }; > + > + ldo1 { > + regulator-name = "nvcc_snvs_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-max-microamp = <300000>; > + regulator-boot-on; > + }; > + > + ldo2 { > + regulator-name = "vdd_snvs_0p8"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + }; > + > + ldo3 { > + regulator-name = "vdd_0p95"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + }; > + > + ldo4 { > + regulator-name = "vdd_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + }; > + }; > + }; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + eeprom@52 { > + compatible = "atmel,24c32"; > + reg = <0x52>; > + pagesize = <32>; > + }; > +}; > + > +&uart2 { /* console */ > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +&usdhc3 { /* eMMC */ > + assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>; > + assigned-clock-rates = <400000000>; > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc3>; > + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; > + bus-width = <8>; > + non-removable; > + status = "okay"; > +}; > + > +&wdog1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_wdog>; > + fsl,ext-reset-output; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_fec1: fec1grp { > + fsl,pins = < > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f > + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 > + >; > + }; > + > + pinctrl_gsc: gscirq { grp suffix. I think dtbs_check should point this out. > + fsl,pins = < > + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x159 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_i2c2: i2c2grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 > + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 > + >; > + }; > + > + pinctrl_usdhc3: usdhc3grp { > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 > + >; > + }; > + > + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { Ditto > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 > + >; > + }; > + > + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { Ditto > + fsl,pins = < > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 > + >; > + }; > + > + pinctrl_wdog: wdoggrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > new file mode 100644 > index 00000000..3f88c4a > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts > @@ -0,0 +1,19 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/dts-v1/; > + > +#include "imx8mm.dtsi" > +#include "imx8mm-venice-gw700x.dtsi" > +#include "imx8mm-venice-gw71xx.dtsi" > + > +/ { > + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; > + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; > + > + chosen { > + stdout-path = &uart2; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi > new file mode 100644 > index 00000000..a4eeb0d > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi This file is included only once, so it should be directly inside imx8mm-venice-gw71xx-0x.dts. Do not create empty DTS just to include DTSI and nothing more. It's really over-complicating simple hierarchy. > @@ -0,0 +1,186 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/ { > + aliases { > + usb0 = &usbotg1; > + usb1 = &usbotg2; > + }; > + > + leds { led-controller > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + user1 { /* GRN */ led-0 > + label = "user1"; label is now deprecated. See the common bindings. > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + user2 { /* RED */ led-1 > + label = "user2"; > + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + }; > + > + pps { > + compatible = "pps-gpio"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pps>; > + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; > + status = "okay"; > + }; > + > + reg_usb_otg1_vbus: regulator-usb-otg1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_usb1_en>; > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg1_vbus"; > + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > +}; > + > +&ecspi2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_spi2>; > + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c2>; > + status = "okay"; > + > + accel@19 { accelerometer > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_accel>; > + compatible = "st,lis2de12"; > + reg = <0x19>; > + st,drdy-int-pin = <1>; > + interrupt-parent = <&gpio4>; > + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; > + interrupt-names = "INT1"; > + }; > +}; > + > +&i2c3 { > + clock-frequency = <400000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > +}; > + > +&sai3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_sai3>; > + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; > + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; > + assigned-clock-rates = <24576000>; > + status = "okay"; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart3>; > + status = "okay"; > +}; > + > +&usbotg1 { > + dr_mode = "otg"; > + vbus-supply = <®_usb_otg1_vbus>; > + status = "okay"; > +}; > + > +&usbotg2 { > + dr_mode = "host"; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + pinctrl_hog: hoggrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* > PLUG_TEST */ > + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* > PCI_USBSEL */ > + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* > PCIE_WDIS# */ > + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* > DIO0 */ > + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* > DIO1 */ > + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* > DIO2 */ > + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* > DIO2 */ > + >; > + }; > + > + pinctrl_accel: accelirq { Same comments as before. > + fsl,pins = < > + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 > + >; > + }; > + > + pinctrl_gpio_leds: gpioledgrp { > + fsl,pins = < > + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 > + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 > + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 > + >; > + }; > + > + pinctrl_pps: ppsgrp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 > + >; > + }; > + > + pinctrl_reg_usb1_en: regusb1grp { > + fsl,pins = < > + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 > + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 > + >; > + }; > + > + pinctrl_spi2: spi2grp { > + fsl,pins = < > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 > + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 > + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 > + >; > + }; > + > + pinctrl_uart3: uart3grp { > + fsl,pins = < > + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 > + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 > + >; > + }; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > new file mode 100644 > index 00000000..b1e7540 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts > @@ -0,0 +1,20 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/dts-v1/; > + > +#include "imx8mm.dtsi" > +#include "imx8mm-venice-gw700x.dtsi" > +#include "imx8mm-venice-gw72xx.dtsi" The same - empty DTS just to include DTSI. Don't multiply files. This is development kit, carrier board, so entire contents of imx8mm-venice-gw72xx.dtsi is *here*. > + > +/ { > + model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit"; > + compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm"; > + > + chosen { > + stdout-path = &uart2; > + }; > +}; > + > diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > new file mode 100644 > index 00000000..3fb0213 > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi > @@ -0,0 +1,311 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2020 Gateworks Corporation > + */ > + > +/ { > + aliases { > + usb0 = &usbotg1; > + usb1 = &usbotg2; > + }; > + > + leds { It seems my comments apply to all your files, so I will finish the review here. Best regards, Krzysztof > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_gpio_leds>; > + > + user1 { /* GRN */ > + label = "user1"; > + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + linux,default-trigger = "heartbeat"; > + }; > + > + user2 { /* RED */ > + label = "user2"; > + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; > + default-state = "off"; > + }; > + };
