On Wed 13 Jan 13:42 CST 2021, AngeloGioacchino Del Regno wrote:
> Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
> very important for regulators like LAB and IBB, which are designed to
> provide from very small to relatively big amounts of current to the
> device (normally, a display).
>
> Now that this regulator supports both voltage setting and current
> limiting in this driver, to me it looked like being somehow essential
> to provide support for SCP and OCP, for two reasons:
> 1. SCP is a drastic measure to prevent damaging "more" hardware in
> the worst situations, if any was damaged, preventing potentially
> drastic issues;
> 2. OCP is a great way to protect the hardware that we're powering
> through these regulators as if anything bad happens, the HW will
> draw more current than expected: in this case, the OCP interrupt
> will fire and the regulators will be immediately shut down,
> preventing hardware damage in many cases.
So when the OCP fires it stops the regulator? Is it automatically
enabled by the re-enabling of the OCP interrupt (if so please mention
this in a comment or so in the code), or does it simply signal the
client driver and it will have to re-enable the regulator?
>
> Both interrupts were successfully tested in a "sort-of" controlled
> manner, with the following methodology:
>
> Short-Circuit Protection (SCP):
> 1. Set LAB/IBB to 4.6/-1.4V, current limit 200mA/50mA;
> 2. Connect a 10 KOhm resistor to LAB/IBB by poking the right traces
> on a FxTec Pro1 smartphone for a very brief time (in short words,
> "just a rapid touch with flying wires");
> 3. The Short-Circuit protection trips: IRQ raises, regulators get
> cut. Recovery OK, test repeated without rebooting, OK.
>
> Over-Current Protection (OCP):
> 1. Set LAB/IBB to the expected voltage to power up the display of
> a Sony Xperia XZ Premium smartphone (Sharp LS055D1SX04), set
> current limit to LAB 200mA, IBB 50mA (the values that this
> display unit needs are 200/800mA);
> 2. Boot the kernel: OCP fires. Recovery never happens because
> the selected current limit is too low, but that's expected.
> Test OK.
>
> 3. Set LAB/IBB to the expected current limits for XZ Premium
> (LAB 200mA, IBB 800mA), but lower than expected voltage,
> specifically LAB 5.4V, IBB -5.6V (instead of 5.6, -5.8V);
> 4. Boot the kernel: OCP fires. Recovery never happens because
> the selected voltage (still in the working range limits)
> is producing a current draw of more than 200mA on LAB.
> Test OK.
>
> Signed-off-by: AngeloGioacchino Del Regno
> <angelogioacchino.delre...@somainline.org>
> ---
> drivers/regulator/qcom-labibb-regulator.c | 447 +++++++++++++++++++++-
> 1 file changed, 444 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/regulator/qcom-labibb-regulator.c
> b/drivers/regulator/qcom-labibb-regulator.c
> index 38ab1eba1c59..38763625241e 100644
> --- a/drivers/regulator/qcom-labibb-regulator.c
> +++ b/drivers/regulator/qcom-labibb-regulator.c
> @@ -17,8 +17,20 @@
>
> #define PMI8998_LAB_REG_BASE 0xde00
> #define PMI8998_IBB_REG_BASE 0xdc00
> +#define PMI8998_IBB_LAB_REG_OFFSET 0x200
>
> #define REG_LABIBB_STATUS1 0x08
> + #define LABIBB_STATUS1_SC_BIT BIT(6)
> + #define LABIBB_STATUS1_VREG_OK_BIT BIT(7)
> +
> +#define REG_LABIBB_INT_SET_TYPE 0x11
> +#define REG_LABIBB_INT_POLARITY_HIGH 0x12
> +#define REG_LABIBB_INT_POLARITY_LOW 0x13
> +#define REG_LABIBB_INT_LATCHED_CLR 0x14
> +#define REG_LABIBB_INT_EN_SET 0x15
> +#define REG_LABIBB_INT_EN_CLR 0x16
> + #define LABIBB_INT_VREG_OK BIT(0)
> + #define LABIBB_INT_VREG_TYPE_LEVEL 0
>
> #define REG_LABIBB_VOLTAGE 0x41
> #define LABIBB_VOLTAGE_OVERRIDE_EN BIT(7)
> @@ -26,8 +38,7 @@
> #define IBB_VOLTAGE_SET_MASK GENMASK(5, 0)
>
> #define REG_LABIBB_ENABLE_CTL 0x46
> -#define LABIBB_STATUS1_VREG_OK_BIT BIT(7)
> -#define LABIBB_CONTROL_ENABLE BIT(7)
> + #define LABIBB_CONTROL_ENABLE BIT(7)
>
> #define REG_LABIBB_PD_CTL 0x47
> #define LAB_PD_CTL_MASK GENMASK(1, 0)
> @@ -56,6 +67,11 @@
> #define LAB_ENABLE_TIME (LABIBB_OFF_ON_DELAY * 2)
> #define IBB_ENABLE_TIME (LABIBB_OFF_ON_DELAY * 10)
> #define LABIBB_POLL_ENABLED_TIME 1000
> +#define OCP_RECOVERY_INTERVAL_MS 500
> +#define SC_RECOVERY_INTERVAL_MS 250
> +#define LABIBB_MAX_OCP_COUNT 4
> +#define LABIBB_MAX_SC_COUNT 3
> +#define LABIBB_MAX_FATAL_COUNT 2
>
> struct labibb_current_limits {
> u32 uA_min;
> @@ -69,10 +85,17 @@ struct labibb_regulator {
> struct regmap *regmap;
> struct regulator_dev *rdev;
> struct labibb_current_limits uA_limits;
> + struct delayed_work ocp_recovery_work;
> + struct delayed_work sc_recovery_work;
> u16 base;
> u8 type;
> u8 dischg_sel;
> u8 soft_start_sel;
> + int sc_irq;
> + int sc_count;
> + int ocp_irq;
> + int ocp_irq_count;
> + int fatal_count;
> };
>
> struct labibb_regulator_data {
> @@ -82,6 +105,379 @@ struct labibb_regulator_data {
> const struct regulator_desc *desc;
> };
>
> +static int qcom_labibb_ocp_hw_enable(struct regulator_dev *rdev)
> +{
> + struct labibb_regulator *vreg = rdev_get_drvdata(rdev);
> + int ret;
> +
> + /* Clear irq latch status to avoid spurious event */
> + ret = regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_LATCHED_CLR,
> + LABIBB_INT_VREG_OK, 1);
Either the clear register reads as 0, making the read-modify-write
pointless, or there are 1s in there which we inadvertently will use to
clear unrelated interrupts with.
So a regmap_write() seems more appropriate.
> + if (ret)
> + return ret;
> +
> + /* Enable OCP HW interrupt */
> + return regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_EN_SET,
> + LABIBB_INT_VREG_OK, 1);
> +}
> +
> +static int qcom_labibb_ocp_hw_disable(struct regulator_dev *rdev)
> +{
> + struct labibb_regulator *vreg = rdev_get_drvdata(rdev);
> +
> + return regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_EN_CLR,
> + LABIBB_INT_VREG_OK, 1);
> +}
> +
> +/*
Please add another '*' to complete the /** and () to the function name,
if you intend for this to be valid kerneldoc.
> + * qcom_labibb_check_ocp_status - Check the Over-Current Protection status
> + * @rdev: Regulator device
rdev != vreg
> + *
> + * This function checks the STATUS1 register for the VREG_OK bit: if it is
> + * set, then there is no Over-Current event.
> + *
> + * Returns: Zero if there is no over-current, 1 if in over-current or
> + * negative number for error
> + */
> +static int qcom_labibb_check_ocp_status(struct labibb_regulator *vreg)
> +{
> + u32 cur_status;
> + int ret;
> +
> + ret = regmap_read(vreg->rdev->regmap, vreg->base + REG_LABIBB_STATUS1,
> + &cur_status);
> + if (ret)
> + return ret;
> +
> + return !(cur_status & LABIBB_STATUS1_VREG_OK_BIT);
> +}
> +
> +static void qcom_labibb_ocp_recovery_worker(struct work_struct *work)
> +{
> + struct labibb_regulator *vreg;
> + const struct regulator_ops *ops;
> + int ret;
> +
> + vreg = container_of(work, struct labibb_regulator,
> + ocp_recovery_work.work);
> + ops = vreg->rdev->desc->ops;
> +
> + if (vreg->ocp_irq_count >= LABIBB_MAX_OCP_COUNT) {
> + /*
> + * If we tried to disable the regulator multiple times but
> + * we kept failing, there's only one last hope to save our
> + * hardware from the death: raise a kernel bug, reboot and
> + * hope that the bootloader kindly saves us. This, though
> + * is done only as paranoid checking, because failing the
> + * regmap write to disable the vreg is almost impossible,
> + * since we got here after multiple regmap R/W.
> + */
> + BUG_ON(vreg->fatal_count > LABIBB_MAX_FATAL_COUNT);
> + dev_err(&vreg->rdev->dev, "LABIBB: CRITICAL: Disabling
> regulator\n");
> +
> + /* Disable the regulator immediately to avoid damage */
> + ret = ops->disable(vreg->rdev);
> + if (ret) {
> + vreg->fatal_count++;
> + goto reschedule;
> + }
> + enable_irq(vreg->ocp_irq);
> + vreg->fatal_count = 0;
> + return;
> + }
> +
> + ret = qcom_labibb_check_ocp_status(vreg);
> + if (ret != 0) {
> + vreg->ocp_irq_count++;
> + goto reschedule;
> + }
> +
> + ret = qcom_labibb_ocp_hw_enable(vreg->rdev);
> + if (ret) {
> + /* We cannot trust it without OCP enabled. */
> + dev_err(vreg->dev, "Cannot enable OCP IRQ\n");
> + vreg->ocp_irq_count++;
> + goto reschedule;
> + }
> +
> + enable_irq(vreg->ocp_irq);
> + /* Everything went fine: reset the OCP count! */
> + vreg->ocp_irq_count = 0;
> + return;
> +
> +reschedule:
> + mod_delayed_work(system_wq, &vreg->ocp_recovery_work,
> + msecs_to_jiffies(OCP_RECOVERY_INTERVAL_MS));
> +}
> +
> +static irqreturn_t qcom_labibb_ocp_isr(int irq, void *chip)
> +{
> + struct labibb_regulator *vreg = chip;
> + const struct regulator_ops *ops = vreg->rdev->desc->ops;
> + int ret;
> +
> + /* If the regulator is not enabled, this is a fake event */
> + if (!ops->is_enabled(vreg->rdev))
> + return 0;
> +
> + /* If we tried to recover for too many times it's not getting better */
> + if (vreg->ocp_irq_count > LABIBB_MAX_OCP_COUNT)
> + return IRQ_NONE;
> +
> + /*
> + * If we (unlikely) can't read this register, to prevent hardware
> + * damage at all costs, we assume that the overcurrent event was
> + * real; Moreover, if the status register is not signaling OCP,
> + * it was a spurious event, so it's all ok.
> + */
> + ret = qcom_labibb_check_ocp_status(vreg);
> + if (ret == 0) {
> + vreg->ocp_irq_count = 0;
> + goto end;
> + }
> + vreg->ocp_irq_count++;
> +
> + /*
> + * Disable the interrupt temporarily, or it will fire continuously;
> + * we will re-enable it in the recovery worker function.
> + */
> + disable_irq(irq);
> +
> + /* Warn the user for overcurrent */
> + dev_warn(vreg->dev, "Over-Current interrupt fired!\n");
> +
> + /* Disable the interrupt to avoid hogging */
> + ret = qcom_labibb_ocp_hw_disable(vreg->rdev);
> + if (ret)
> + goto end;
> +
> + /* Signal overcurrent event to drivers */
> + regulator_notifier_call_chain(vreg->rdev,
> + REGULATOR_EVENT_OVER_CURRENT, NULL);
> +
> +end:
> + /* Schedule the recovery work */
> + schedule_delayed_work(&vreg->ocp_recovery_work,
> + msecs_to_jiffies(OCP_RECOVERY_INTERVAL_MS));
> + if (ret)
> + return IRQ_NONE;
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int qcom_labibb_set_ocp(struct regulator_dev *rdev)
> +{
> + struct labibb_regulator *vreg = rdev_get_drvdata(rdev);
> + char *ocp_irq_name;
> + u32 irq_flags = IRQF_ONESHOT;
> + int irq_trig_low, ret;
> +
> + /* If there is no OCP interrupt, there's nothing to set */
> + if (vreg->ocp_irq <= 0)
> + return -EINVAL;
> +
> + ocp_irq_name = devm_kasprintf(vreg->dev, GFP_KERNEL, "%s-over-current",
> + vreg->desc.name);
> + if (!ocp_irq_name)
> + return -ENOMEM;
> +
> + /* IRQ polarities - LAB: trigger-low, IBB: trigger-high */
> + switch (vreg->type) {
> + case QCOM_LAB_TYPE:
> + irq_flags |= IRQF_TRIGGER_LOW;
> + irq_trig_low = 1;
> + break;
> + case QCOM_IBB_TYPE:
> + irq_flags |= IRQF_TRIGGER_HIGH;
> + irq_trig_low = 0;
> + break;
> + default:
> + return -EINVAL;
> + }
> +
> + /* Activate OCP HW level interrupt */
> + ret = regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_SET_TYPE,
> + LABIBB_INT_VREG_OK,
> + LABIBB_INT_VREG_TYPE_LEVEL);
> + if (ret)
> + return ret;
> +
> + /* Set OCP interrupt polarity */
> + ret = regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_POLARITY_HIGH,
> + LABIBB_INT_VREG_OK, !irq_trig_low);
> + if (ret)
> + return ret;
> + ret = regmap_update_bits(rdev->regmap,
> + vreg->base + REG_LABIBB_INT_POLARITY_LOW,
> + LABIBB_INT_VREG_OK, irq_trig_low);
> + if (ret)
> + return ret;
> +
> + ret = qcom_labibb_ocp_hw_enable(rdev);
> + if (ret)
> + return ret;
> +
> + return devm_request_threaded_irq(vreg->dev, vreg->ocp_irq, NULL,
> + qcom_labibb_ocp_isr, irq_flags,
> + ocp_irq_name, vreg);
> +}
> +
> +/*
> + * qcom_labibb_check_sc_status - Check the Short Circuit Protection status
> + * @rdev: Regulator device
> + *
> + * This function checks the STATUS1 register on both LAB and IBB regulators
> + * for the ShortCircuit bit: if it is set on *any* of them, then we have
> + * experienced a short-circuit event.
> + *
> + * Returns: Zero if there is no short-circuit, 1 if in short-circuit or
> + * negative number for error
> + */
> +static int qcom_labibb_check_sc_status(struct labibb_regulator *vreg)
> +{
> + u32 ibb_status, ibb_reg, lab_status, lab_reg;
> + int ret;
> +
> + /* We have to work on both regulators due to PBS... */
> + lab_reg = ibb_reg = vreg->base;
> + if (vreg->type == QCOM_LAB_TYPE)
> + ibb_reg -= PMI8998_IBB_LAB_REG_OFFSET;
Minus? The register comes before the base address?
> + else
> + lab_reg += PMI8998_IBB_LAB_REG_OFFSET;
> +
> + ret = regmap_read(vreg->rdev->regmap, lab_reg, &lab_status);
> + if (ret)
> + return ret;
> + ret = regmap_read(vreg->rdev->regmap, ibb_reg, &ibb_status);
> + if (ret)
> + return ret;
> +
> + return !!(lab_status & LABIBB_STATUS1_SC_BIT) ||
> + !!(ibb_status & LABIBB_STATUS1_SC_BIT);
> +}
> +
> +static void qcom_labibb_sc_recovery_worker(struct work_struct *work)
> +{
> + struct labibb_regulator *vreg;
> + const struct regulator_ops *ops;
> + u32 lab_reg, ibb_reg, temp, val;
> + bool pbs_cut = false;
> + int i, sc, ret;
> +
> + vreg = container_of(work, struct labibb_regulator,
> + sc_recovery_work.work);
> + ops = vreg->rdev->desc->ops;
> +
> + /*
> + * If we tried to check the regulator status multiple times but we
> + * kept failing, then just bail out, as the Portable Batch System
> + * (PBS) will disable the vregs for us, preventing hardware damage.
> + */
> + if (vreg->fatal_count > LABIBB_MAX_FATAL_COUNT)
> + return;
> +
> + /* Too many short-circuit events. Throw in the towel. */
> + if (vreg->sc_count > LABIBB_MAX_SC_COUNT)
> + return;
> +
> + /*
> + * The Portable Batch System (PBS) automatically disables LAB
> + * and IBB when a short-circuit event is detected, so we have to
> + * check and work on both of them at the same time.
> + */
> + lab_reg = ibb_reg = vreg->base;
> + if (vreg->type == QCOM_LAB_TYPE)
> + ibb_reg -= PMI8998_IBB_LAB_REG_OFFSET;
> + else
> + lab_reg += PMI8998_IBB_LAB_REG_OFFSET;
> +
> + sc = qcom_labibb_check_sc_status(vreg);
> + if (sc)
> + goto reschedule;
> +
> + for (i = 0; i < LABIBB_MAX_SC_COUNT; i++) {
> + ret = regmap_read(vreg->regmap, lab_reg, &temp);
> + if (ret) {
> + vreg->fatal_count++;
> + goto reschedule;
> + }
> + val = temp;
> +
> + ret = regmap_read(vreg->regmap, ibb_reg, &temp);
> + if (ret) {
> + vreg->fatal_count++;
> + goto reschedule;
> + }
> + val &= temp;
Perhaps using two variables, with suitable names makes this more
maintainable?
> +
> + if (val & LABIBB_CONTROL_ENABLE) {
Flip this around and do pbs_cut = true; break; in the conditional, to
not end the loop with a conditional continue and an unconditional break.
> + usleep_range(5000, 6000);
> + continue;
> + }
> + pbs_cut = true;
> + break;
> + }
> + if (pbs_cut)
> + goto reschedule;
> +
> + /*
> + * If we have reached this point, we either had a spurious SC IRQ
> + * or we have successfully recovered from the SC condition, which
Wouldn't it make sense to put the "recovered from the SC condition"
before the "spurious" part in this sentence - just seems like this is
the scenario we're most likely looking for.
Regards,
Bjorn
> + * means that we can re-enable the regulators, if they have ever
> + * been disabled by the PBS.
> + */
> + ret = ops->enable(vreg->rdev);
> + if (ret)
> + goto reschedule;
> +
> + /* Everything went fine: reset the OCP count! */
> + vreg->sc_count = 0;
> + enable_irq(vreg->sc_irq);
> + return;
> +
> +reschedule:
> + /*
> + * Now that we have done basic handling of the short-circuit,
> + * reschedule this worker in the regular system workqueue, as
> + * taking action is not truly urgent anymore.
> + */
> + vreg->sc_count++;
> + mod_delayed_work(system_wq, &vreg->sc_recovery_work,
> + msecs_to_jiffies(SC_RECOVERY_INTERVAL_MS));
> +}
> +
> +static irqreturn_t qcom_labibb_sc_isr(int irq, void *chip)
> +{
> + struct labibb_regulator *vreg = chip;
> +
> + if (vreg->sc_count > LABIBB_MAX_SC_COUNT)
> + return IRQ_NONE;
> +
> + /* Warn the user for short circuit */
> + dev_warn(vreg->dev, "Short-Circuit interrupt fired!\n");
> +
> + /*
> + * Disable the interrupt temporarily, or it will fire continuously;
> + * we will re-enable it in the recovery worker function.
> + */
> + disable_irq(irq);
> +
> + /* Signal out of regulation event to drivers */
> + regulator_notifier_call_chain(vreg->rdev,
> + REGULATOR_EVENT_REGULATION_OUT, NULL);
> +
> + /* Schedule the short-circuit handling as high-priority work */
> + mod_delayed_work(system_highpri_wq, &vreg->sc_recovery_work,
> + msecs_to_jiffies(SC_RECOVERY_INTERVAL_MS));
> + return IRQ_HANDLED;
> +}
> +
> +
> static int qcom_labibb_set_current_limit(struct regulator_dev *rdev,
> int min_uA, int max_uA)
> {
> @@ -210,6 +606,7 @@ static const struct regulator_ops qcom_labibb_ops = {
> .set_current_limit = qcom_labibb_set_current_limit,
> .get_current_limit = qcom_labibb_get_current_limit,
> .set_soft_start = qcom_labibb_set_soft_start,
> + .set_over_current_protection = qcom_labibb_set_ocp,
> };
>
> static const struct regulator_desc pmi8998_lab_desc = {
> @@ -291,7 +688,7 @@ static int qcom_labibb_regulator_probe(struct
> platform_device *pdev)
> struct labibb_regulator *vreg;
> struct device *dev = &pdev->dev;
> struct regulator_config cfg = {};
> -
> + struct device_node *reg_node;
> const struct of_device_id *match;
> const struct labibb_regulator_data *reg_data;
> struct regmap *reg_regmap;
> @@ -309,6 +706,8 @@ static int qcom_labibb_regulator_probe(struct
> platform_device *pdev)
> return -ENODEV;
>
> for (reg_data = match->data; reg_data->name; reg_data++) {
> + char *sc_irq_name;
> + int irq = 0;
>
> /* Validate if the type of regulator is indeed
> * what's mentioned in DT.
> @@ -331,10 +730,44 @@ static int qcom_labibb_regulator_probe(struct
> platform_device *pdev)
> if (!vreg)
> return -ENOMEM;
>
> + sc_irq_name = devm_kasprintf(dev, GFP_KERNEL,
> + "%s-short-circuit",
> + reg_data->name);
> + if (!sc_irq_name)
> + return -ENOMEM;
> +
> + reg_node = of_get_child_by_name(pdev->dev.of_node,
> + reg_data->name);
> + if (!reg_node)
> + return -EINVAL;
> +
> + /* The Short Circuit interrupt is critical */
> + irq = of_irq_get_byname(reg_node, "sc-err");
> + if (irq <= 0) {
> + if (irq == 0)
> + irq = -EINVAL;
> +
> + return dev_err_probe(vreg->dev, irq,
> + "Short-circuit irq not found.\n");
> + }
> + vreg->sc_irq = irq;
> +
> + /* OverCurrent Protection IRQ is optional */
> + irq = of_irq_get_byname(reg_node, "ocp");
> + vreg->ocp_irq = irq;
> + vreg->ocp_irq_count = 0;
> + of_node_put(reg_node);
> +
> vreg->regmap = reg_regmap;
> vreg->dev = dev;
> vreg->base = reg_data->base;
> vreg->type = reg_data->type;
> + INIT_DELAYED_WORK(&vreg->sc_recovery_work,
> + qcom_labibb_sc_recovery_worker);
> +
> + if (vreg->ocp_irq > 0)
> + INIT_DELAYED_WORK(&vreg->ocp_recovery_work,
> + qcom_labibb_ocp_recovery_worker);
>
> switch (vreg->type) {
> case QCOM_LAB_TYPE:
> @@ -369,6 +802,14 @@ static int qcom_labibb_regulator_probe(struct
> platform_device *pdev)
> reg_data->name, ret);
> return PTR_ERR(vreg->rdev);
> }
> +
> + ret = devm_request_threaded_irq(vreg->dev, vreg->sc_irq, NULL,
> + qcom_labibb_sc_isr,
> + IRQF_ONESHOT |
> + IRQF_TRIGGER_RISING,
> + sc_irq_name, vreg);
> + if (ret)
> + return ret;
> }
>
> return 0;
> --
> 2.29.2
>
