On Thu, 2021-01-21 at 16:31 -0600, Bjorn Helgaas wrote: > [+cc Alex and Mingchuang et al from > https://lore.kernel.org/r/20210112072739.31624-1-mingchuang.q...@mediatek.com] > > On Tue, Jan 19, 2021 at 04:14:10PM +0300, Mika Westerberg wrote: > > PCIe r5.0, sec 7.5.3.16 says that the downstream ports must reset the > > LTR enable bit if the link goes down (port goes DL_Down status). Now, if > > we had LTR previously enabled and the PCIe endpoint gets hot-removed and > > then hot-added back the ->ltr_path of the downstream port is still set > > but the port now does not have the LTR enable bit set anymore. > > > > For this reason check if the bridge upstream had LTR enabled previously > > and re-enable it before enabling LTR for the endpoint. > > > > Reported-by: Utkarsh H Patel <utkarsh.h.pa...@intel.com> > > Signed-off-by: Mika Westerberg <mika.westerb...@linux.intel.com> > > I think this and Mingchuang's patch, which is essentially identical, > are right and solves the problem for hot-remove/hot-add. In that > scenario we call pci_configure_ltr() on the hot-added device, and > with this patch, we'll re-enable LTR on the bridge leading to the new > device before enabling LTR on the new device itself. > > But don't we have a similar problem if we simply do a Fundamental > Reset on a device? I think the reset path will restore the device's > state, including PCI_EXP_DEVCTL2, but it doesn't do anything with the > upstream bridge, does it? >
Yes. I think the same problem exists under such scenario, and that’s the issue my patch intends to resolve. I also prepared a v2 patch for review(update the patch description). Shall I submit the v2 patch for review? > So if a bridge and a device below it both have LTR enabled, can't we > have the following: > > - bridge LTR enabled > - device LTR enabled > - reset device, e.g., via Secondary Bus Reset > - link goes down, bridge disables LTR > - link comes back up, LTR disabled in both bridge and device > - restore device state, including LTR enable > - device sends LTR message > - bridge reports Unsupported Request > > > --- > > Previous version can be found here: > > > > > > https://lore.kernel.org/linux-pci/20210114134724.79511-1-mika.westerb...@linux.intel.com/ > > > > Changes from the previous version: > > > > * Corrected typos in the commit message > > * No need to call pcie_downstream_port() > > > > drivers/pci/probe.c | 17 ++++++++++++++++- > > 1 file changed, 16 insertions(+), 1 deletion(-) > > > > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c > > index 0eb68b47354f..a4a8c0305fb9 100644 > > --- a/drivers/pci/probe.c > > +++ b/drivers/pci/probe.c > > @@ -2153,7 +2153,7 @@ static void pci_configure_ltr(struct pci_dev *dev) > > { > > #ifdef CONFIG_PCIEASPM > > struct pci_host_bridge *host = pci_find_host_bridge(dev->bus); > > - struct pci_dev *bridge; > > + struct pci_dev *bridge = NULL; > > u32 cap, ctl; > > > > if (!pci_is_pcie(dev)) > > @@ -2191,6 +2191,21 @@ static void pci_configure_ltr(struct pci_dev *dev) > > if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT || > > ((bridge = pci_upstream_bridge(dev)) && > > bridge->ltr_path)) { > > + /* > > + * Downstream ports reset the LTR enable bit when the > > + * link goes down (e.g on hot-remove) so re-enable the > > + * bit here if not set anymore. > > + * PCIe r5.0, sec 7.5.3.16. > > + */ > > + if (bridge) { > > + pcie_capability_read_dword(bridge, PCI_EXP_DEVCTL2, > > &ctl); > > + if (!(ctl & PCI_EXP_DEVCTL2_LTR_EN)) { > > + pci_dbg(bridge, "re-enabling LTR\n"); > > + pcie_capability_set_word(bridge, > > PCI_EXP_DEVCTL2, > > + > > PCI_EXP_DEVCTL2_LTR_EN); > > + } > > + } > > + pci_dbg(dev, "enabling LTR\n"); > > pcie_capability_set_word(dev, PCI_EXP_DEVCTL2, > > PCI_EXP_DEVCTL2_LTR_EN); > > dev->ltr_path = 1; > > -- > > 2.29.2 > >