From: Sumit Semwal <[email protected]> Enabling the Display panel for beryllium phone (Xiaomi Pocophone F1) requires DSI labibb regulators and panel dts nodes to be added. It is also required to keep some of the regulators as always-on.
Signed-off-by: Sumit Semwal <[email protected]> Signed-off-by: Amit Pundir <[email protected]> --- .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 55 ++++++++++++++++++++++ 1 file changed, 55 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts index cd15ae0347e8..e09effa555f1 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts @@ -160,6 +160,14 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + regulator-always-on; + }; + vreg_l17a_1p3: ldo17 { regulator-min-microvolt = <1304000>; regulator-max-microvolt = <1304000>; @@ -194,6 +202,7 @@ regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; }; }; }; @@ -207,6 +216,44 @@ firmware-name = "qcom/sdm845/cdsp.mdt"; }; +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l26a_1p2>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&tianma_nt36672a_in_0>; + data-lanes = <0 1 2 3>; + }; + }; + }; + + panel@0 { + compatible = "tianma,fhd-video"; + reg = <0>; + vddi0-supply = <&vreg_l14a_1p88>; + vddpos-supply = <&lab>; + vddneg-supply = <&ibb>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + #address-cells = <1>; + #size-cells = <0>; + + port { + tianma_nt36672a_in_0: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l1a_0p875>; +}; + &gcc { protected-clocks = <GCC_QSPI_CORE_CLK>, <GCC_QSPI_CORE_CLK_SRC>, @@ -274,6 +321,14 @@ }; +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &mss_pil { status = "okay"; firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; -- 2.7.4
