From: Sumit Semwal <[email protected]> Enabling the Display panel for beryllium phone (Xiaomi Pocophone F1) requires DSI labibb regulators and panel dts nodes to be added. It is also required to keep some of the regulators as always-on.
Signed-off-by: Sumit Semwal <[email protected]> Signed-off-by: Amit Pundir <[email protected]> --- v2: Rebased to mainline (v5.11-rc6) and fixed build warnings. .../boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 58 ++++++++++++++++++++++ 1 file changed, 58 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts index 86cbae63eaf7..034246b5c529 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts @@ -157,6 +157,14 @@ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; + regulator-always-on; + }; + vreg_l17a_1p3: ldo17 { regulator-min-microvolt = <1304000>; regulator-max-microvolt = <1304000>; @@ -191,6 +199,7 @@ regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + regulator-boot-on; }; }; }; @@ -200,6 +209,47 @@ firmware-name = "qcom/sdm845/cdsp.mdt"; }; +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l26a_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&tianma_nt36672a_in_0>; + data-lanes = <0 1 2 3>; + }; + }; + }; + + panel@0 { + compatible = "tianma,fhd-video"; + reg = <0>; + vddi0-supply = <&vreg_l14a_1p88>; + vddpos-supply = <&lab>; + vddneg-supply = <&ibb>; + + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + port { + tianma_nt36672a_in_0: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l1a_0p875>; +}; + &gcc { protected-clocks = <GCC_QSPI_CORE_CLK>, <GCC_QSPI_CORE_CLK_SRC>, @@ -215,6 +265,14 @@ }; }; +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &mss_pil { status = "okay"; firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt"; -- 2.7.4
