On 2/11/21 4:24 AM, Kalle Valo wrote:
Shuah Khan <sk...@linuxfoundation.org> writes:
On 2/10/21 1:28 AM, Kalle Valo wrote:
Wen Gong <wg...@codeaurora.org> writes:
On 2021-02-10 08:42, Shuah Khan wrote:
ath10k_mac_get_rate_flags_ht() floods dmesg with the following
messages,
when it fails to find a match for mcs=7 and rate=1440.
supported_ht_mcs_rate_nss2:
{7, {1300, 2700, 1444, 3000} }
ath10k_pci 0000:02:00.0: invalid ht params rate 1440 100kbps nss 2
mcs 7
dev_warn_ratelimited() isn't helping the noise. Use dev_warn_once()
instead.
Signed-off-by: Shuah Khan <sk...@linuxfoundation.org>
---
drivers/net/wireless/ath/ath10k/mac.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/ath/ath10k/mac.c
b/drivers/net/wireless/ath/ath10k/mac.c
index 3545ce7dce0a..276321f0cfdd 100644
--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -8970,8 +8970,9 @@ static void ath10k_mac_get_rate_flags_ht(struct
ath10k *ar, u32 rate, u8 nss, u8
*bw |= RATE_INFO_BW_40;
*flags |= RATE_INFO_FLAGS_SHORT_GI;
} else {
- ath10k_warn(ar, "invalid ht params rate %d 100kbps nss %d mcs
%d",
- rate, nss, mcs);
+ dev_warn_once(ar->dev,
+ "invalid ht params rate %d 100kbps nss %d mcs %d",
+ rate, nss, mcs);
}
}
The {7, {1300, 2700, 1444, 3000} } is a correct value.
The 1440 is report from firmware, its a wrong value, it has fixed in
firmware.
In what version?
Here is the info:
ath10k_pci 0000:02:00.0: qca6174 hw3.2 target 0x05030000 chip_id
0x00340aff sub 17aa:0827
ath10k_pci 0000:02:00.0: firmware ver WLAN.RM.4.4.1-00140-QCARMSWPZ-1
api 6 features wowlan,ignore-otp,mfp crc32 29eb8ca1
ath10k_pci 0000:02:00.0: board_file api 2 bmi_id N/A crc32 4ac0889b
ath10k_pci 0000:02:00.0: htt-ver 3.60 wmi-op 4 htt-op 3 cal otp
max-sta 32 raw 0 hwcrypto 1
If change it to dev_warn_once, then it will have no chance to find the
other wrong values which report by firmware, and it indicate
a wrong value to mac80211/cfg80211 and lead "iw wlan0 station dump"
get a wrong bitrate.
Agreed.
I agree, we should keep this warning. If the firmware still keeps
sending invalid rates we should add a specific check to ignore the known
invalid values, but not all of them.
Would it be helpful to adjust the default rate limits and set the to
a higher value instead. It might be difficult to account all possible
invalid values?
Something like, ath10k_warn_ratelimited() to adjust the
DEFAULT_RATELIMIT_INTERVAL and DEFAULT_RATELIMIT_BURST using
DEFINE_RATELIMIT_STATE
Let me know if you like this idea. I can send a patch in to do this.
I will hang on to this firmware version for a little but longer, so
we have a test case. :)
I would rather first try to fix the root cause, which is the firmware
sending invalid rates. Wen, you mentioned there's a fix in firmware. Do
you know which firmware version (and branch) has the fix?
Picking this back up. Wen, which firmware version has this fix? I can
test this on my system and get rid of the noisy messages. :)
thanks,
-- Shuah