On Thu, Mar 04, 2021 at 10:27:35AM -0800, Guru Das Srinagesh wrote: > On Thu, Nov 12, 2020 at 07:33:12PM +0000, Mark Brown wrote:
> > supposed to do. Nothing here says what POLARITY_HI and POLARITY_LO are, > > how they interact or anything. > The POLARITY_HI and POLARITY_LO registers were described very briefly in > the cover letter. If an interrupt is already configured as either edge- > or level-triggered, setting the corresponding bit for it in the > POLARITY_HI register further configures it as rising-edge or level-high > triggered (as the case may be), while setting the same bit in > POLARITY_LO further configures it as falling-edge or level-low > triggered. I could certainly add this information to the commit message > as well. So this is just a trigger type control that's in two discontiguous bits possibly in different registers or something? This doesn't sound like anything generic with the API you're describing, if that's what it is the interface should also handle things like four bits (one for each type) or having the different values mapped differently within the two bits that are spread out (eg, you could have one bit for polarity and another for edge/level). > > For the address offsets I'm not sure that this is the best way to > > represent things. It looks like the hardware this is trying to describe > > is essentially a bunch of separate interrupt controllers that happen to > > share an upstream interrupt > Sorry but isn't this essentially the same as what the framework already knows > as > the "sub-irq" concept, with the key difference that the register stride > is not fixed? Everything else is the same (except for a couple of minor > points noted below) - a main IRQ register that indicates sub-irq blocks > that have unhandled interrupts, as well as interrupt handling and > servicing. Like I said in my original review it is extremely hard to tell from your patch what you are trying to implement, and it's now been more than four months since you sent it which isn't helping anything. This means it is also extremely hard to tell if the patch is doing the same thing as sub_irq. IIRC it appeared that there was no top level interrupt status register, the point with sub_irq is that we don't need to read all the status registers because there's a top level status register which says which of them have signals in them (including the possibility that more than one bit in the top level status might indicate the same leaf status register). If the device doesn't have that it doesn't have sub_irqs. Note that sub_irq only affects status register reads, it doesn't affect other things like acking or masking. On the other hand if this *is* the same thing as sub_irqs then why is it completely separate code and not sharing anything with it? As I said at the time you need to split this into at least two distinct patches with clear changelogs which explain what they are trying to implement, I don't think it's useful to discuss this further without that. I can't give you any clearer advice on how to implement whatever you are trying to implement without having some idea of what that is. > > clearer if at least the implementation looked like this. Instead of > > having to check for this array of offsets at every use point (which is > > going to be rarely used and hence prone to bugs) > Well, using irq_reg_stride already does exactly this - calculating the > right register to access at every use point, as an offset from the _base > register (status, ack, type, et c.). Peripheral offsets would just be > another way of calculating the right register, that's all. And we could > have a macro as well. The stride code is executed in all paths, it doesn't add conditional statements all over the place. This helps a lot, we know it's being run all the time as opposed to being a lot of separate code paths that are rarely run - the case without a stride is just a stride of 1. > Sure, I can look into how this approach would look like, but given that > the QCOM register arrangement of main vs sub-irq is essentially the same > as what the framework currently understands, couldn't we simply have a > macro to change the way the right register offset is calculated > (irq_reg_stride vs. peripheral offsets)? I'm not sure macros all over the place is going to be clearer than conditional statements all over the place. As with what you were saying about sub_irq if you think the two things are equivalent then why is one not implemented in terms of the other rather than doing conditional code on every single use? > Also, could you elaborate more on the genirq route? I'm not sure where > to start looking to evaluate one route vs the other. Register a separate regmap-irq for each of these perhiperals in your list, using the same parent interrupt for all of them and setting IRQF_SHARED. They will then be handled like any other shared interrupt, if the parent interrupt fires then genirq will go through and call each of the handlers until one reports that it handled an interrupt.
signature.asc
Description: PGP signature