On Fri 05 Mar 15:35 CST 2021, Caleb Connolly wrote: Please add "qcom: " to $subject as well.
> Add a minimal devicetree capable of booting on the Pixel 2 XL MSM8998 > device. > > It's currently possible to boot the device into postmarketOS with USB > networking, however the display panel depends on Display Stream > Compression which is not yet supported in the kernel. > > The bootloader also requires that the dtbo partition contains a device > tree overlay with a particular id which has to be overlayed onto the > existing dtb. It's possible to use a specially crafted dtbo partition to > workaround this, more information is available here: > > https://gitlab.com/calebccff/dtbo-google-wahoo-mainline > So it's not possible to just erase the dto, like on most other devices? > Signed-off-by: Caleb Connolly <ca...@connolly.tech> > --- > It's possible to get wifi working by running Bjorns diag-router in the > background, without this the wifi firmware crashes every 10 seconds or > so. This is the same issue encountered on the OnePlus 5. > > arch/arm64/boot/dts/qcom/Makefile | 1 + > .../boot/dts/qcom/msm8998-google-taimen.dts | 14 + > .../boot/dts/qcom/msm8998-google-wahoo.dtsi | 391 ++++++++++++++++++ > 3 files changed, 406 insertions(+) > create mode 100644 arch/arm64/boot/dts/qcom/msm8998-google-taimen.dts > create mode 100644 arch/arm64/boot/dts/qcom/msm8998-google-wahoo.dtsi > > diff --git a/arch/arm64/boot/dts/qcom/Makefile > b/arch/arm64/boot/dts/qcom/Makefile > index 5113fac80b7a..d942d3ec3928 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_QCOM) += > msm8994-msft-lumia-cityman.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-sumire.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb > +dtb-$(CONFIG_ARCH_QCOM) += msm8998-google-taimen.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-lenovo-miix-630.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb > diff --git a/arch/arm64/boot/dts/qcom/msm8998-google-taimen.dts > b/arch/arm64/boot/dts/qcom/msm8998-google-taimen.dts > new file mode 100644 > index 000000000000..ffaaafe14037 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8998-google-taimen.dts > @@ -0,0 +1,14 @@ > +// SPDX-License-Identifier: GPL-2.0-only Would you be willing to release these as BSD-3-Clause instead? > +/* > + * Copyright (c) 2020, Caleb Connolly <ca...@connolly.tech> > + */ > + > +/dts-v1/; > + > +#include "msm8998-google-wahoo.dtsi" > + > +/ { > + model = "Google Pixel 2 XL"; > + compatible = "google,taimen", "google,wahoo", "qcom,msm8998", > "qcom,msm8998-mtp"; > + qcom,msm-id = <0x124 0x20001>; > +}; > diff --git a/arch/arm64/boot/dts/qcom/msm8998-google-wahoo.dtsi > b/arch/arm64/boot/dts/qcom/msm8998-google-wahoo.dtsi > new file mode 100644 > index 000000000000..0c221ead2df7 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8998-google-wahoo.dtsi > @@ -0,0 +1,391 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* Copyright (c) 2020 Caleb Connolly <ca...@connolly.tech> */ > + > +#include "msm8998.dtsi" > +#include "pm8998.dtsi" > +#include "pmi8998.dtsi" > +#include "pm8005.dtsi" > + > +/delete-node/ &mpss_mem; > +/delete-node/ &venus_mem; > +/delete-node/ &mba_mem; > +/delete-node/ &slpi_mem; > + > +/ { > + aliases { > + }; > + > + chosen { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + /* Add "earlycon" intended to be used in combination with UART > serial console */ > + bootargs = "clk_ignore_unused earlycon > console=ttyGS0,115200";// loglevel=10 drm.debug=15 debug"; Please drop earlycon from this list (user should be able to add it if they care later?) and use stdout-path to set the console, like we do on other devices. > + }; > + > + reserved-memory { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + mpss_mem: memory@8cc00000 { > + reg = <0 0x8cc00000 0 0x7800000>; > + no-map; > + }; > + > + venus_mem: memory@94400000 { > + reg = <0 0x94400000 0 0x500000>; > + no-map; > + }; > + > + mba_mem: memory@94100000 { > + reg = <0 0x94900000 0 0x200000>; > + no-map; > + }; > + > + slpi_mem: memory@94b00000 { > + reg = <0 0x94b00000 0 0x700000>; > + no-map; > + }; > + > + ramoops: ramoops@a1810000 { > + compatible = "ramoops"; > + reg = <0 0xa1810000 0 0x200000>; > + record-size = <0x20000>; > + console-size = <0x100000>; > + pmsg-size = <0x80000>; > + }; > + }; > + > + vph_pwr: vph-pwr-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vph_pwr"; > + regulator-always-on; > + regulator-boot-on; > + }; > +}; > + > +&blsp1_uart3 { > + status = "disabled"; > + > + bluetooth { > + compatible = "qcom,wcn3990-bt"; > + > + vddio-supply = <&vreg_s4a_1p8>; > + vddxo-supply = <&vreg_l7a_1p8>; > + vddrf-supply = <&vreg_l17a_1p3>; > + vddch0-supply = <&vreg_l25a_3p3>; > + max-speed = <3200000>; > + }; > +}; > + > +&pcie0 { > + status = "disabled"; Isn't &pcie0 already disabled, from msm8998.dtsi? > +}; > + > +&pm8005_lsid1 { > + pm8005-regulators { > + compatible = "qcom,pm8005-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + > + pm8005_s1: s1 { /* VDD_GFX supply */ > + regulator-min-microvolt = <524000>; > + regulator-max-microvolt = <1100000>; > + regulator-enable-ramp-delay = <500>; > + > + /* hack until we rig up the gpu consumer */ > + regulator-always-on; > + }; > + }; > +}; > + > +&qusb2phy { > + status = "okay"; > + > + vdda-pll-supply = <&vreg_l12a_1p8>; > + vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; > +}; > + > +&remoteproc_adsp { > + status = "okay"; > + > + firmware-name = "qcom/pixel2/adsp.mdt"; > +}; > + > +&remoteproc_mss { > + firmware-name = "qcom/pixel2/mba.mbn", > + "qcom/pixel2/modem.mdt"; > +}; > + > +&remoteproc_slpi { > + status = "okay"; > + > + firmware-name = "qcom/pixel2/slpi_v2.mdt"; > +}; > + > +&rpm_requests { > + pm8998-regulators { > + compatible = "qcom,rpm-pm8998-regulators"; > + > + vdd_s1-supply = <&vph_pwr>; > + vdd_s2-supply = <&vph_pwr>; > + vdd_s3-supply = <&vph_pwr>; > + vdd_s4-supply = <&vph_pwr>; > + vdd_s5-supply = <&vph_pwr>; > + vdd_s6-supply = <&vph_pwr>; > + vdd_s7-supply = <&vph_pwr>; > + vdd_s8-supply = <&vph_pwr>; > + vdd_s9-supply = <&vph_pwr>; > + vdd_s10-supply = <&vph_pwr>; > + vdd_s11-supply = <&vph_pwr>; > + vdd_s12-supply = <&vph_pwr>; > + vdd_s13-supply = <&vph_pwr>; > + vdd_l1_l27-supply = <&vreg_s7a_1p025>; > + vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; > + vdd_l3_l11-supply = <&vreg_s7a_1p025>; > + vdd_l4_l5-supply = <&vreg_s7a_1p025>; > + vdd_l6-supply = <&vreg_s5a_2p04>; > + vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; > + vdd_l9-supply = <&vreg_bob>; > + vdd_l10_l23_l25-supply = <&vreg_bob>; > + vdd_l13_l19_l21-supply = <&vreg_bob>; > + vdd_l16_l28-supply = <&vreg_bob>; > + vdd_l18_l22-supply = <&vreg_bob>; > + vdd_l20_l24-supply = <&vreg_bob>; > + vdd_l26-supply = <&vreg_s3a_1p35>; > + vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; > + > + vreg_s3a_1p35: s3 { > + regulator-min-microvolt = <1352000>; > + regulator-max-microvolt = <1352000>; > + }; > + vreg_s4a_1p8: s4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-allow-set-load; > + }; > + vreg_s5a_2p04: s5 { > + regulator-min-microvolt = <1904000>; > + regulator-max-microvolt = <2040000>; > + }; > + vreg_s7a_1p025: s7 { > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1028000>; > + }; > + vreg_l1a_0p875: l1 { > + regulator-min-microvolt = <880000>; > + regulator-max-microvolt = <880000>; > + }; > + vreg_l2a_1p2: l2 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + vreg_l3a_1p0: l3 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + vreg_l5a_0p8: l5 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + }; > + vreg_l6a_1p8: l6 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <1808000>; > + }; > + vreg_l7a_1p8: l7 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + vreg_l8a_1p2: l8 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + }; > + vreg_l9a_1p8: l9 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + vreg_l10a_1p8: l10 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + vreg_l11a_1p0: l11 { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + }; > + vreg_l12a_1p8: l12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + vreg_l13a_2p95: l13 { > + regulator-min-microvolt = <1808000>; > + regulator-max-microvolt = <2960000>; > + }; > + vreg_l14a_1p88: l14 { > + regulator-min-microvolt = <1880000>; > + regulator-max-microvolt = <1880000>; > + }; > + vreg_15a_1p8: l15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + vreg_l16a_2p7: l16 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + vreg_l17a_1p3: l17 { > + regulator-min-microvolt = <1304000>; > + regulator-max-microvolt = <1304000>; > + }; > + vreg_l18a_2p7: l18 { > + regulator-min-microvolt = <2704000>; > + regulator-max-microvolt = <2704000>; > + }; > + vreg_l19a_3p0: l19 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + vreg_l20a_2p95: l20 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-allow-set-load; > + }; > + vreg_l21a_2p95: l21 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-allow-set-load; > + regulator-system-load = <800000>; > + }; > + vreg_l22a_2p85: l22 { > + regulator-min-microvolt = <2864000>; > + regulator-max-microvolt = <2864000>; > + }; > + vreg_l23a_3p3: l23 { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3312000>; > + }; > + vreg_l24a_3p075: l24 { > + regulator-min-microvolt = <3088000>; > + regulator-max-microvolt = <3088000>; > + }; > + vreg_l25a_3p3: l25 { > + regulator-min-microvolt = <3104000>; > + regulator-max-microvolt = <3312000>; > + }; > + vreg_l26a_1p2: l26 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-allow-set-load; > + }; > + vreg_l28_3p0: l28 { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3008000>; > + }; > + > + vreg_lvs1a_1p8: lvs1 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + vreg_lvs2a_1p8: lvs2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + }; > + > + pmi8998-regulators { > + compatible = "qcom,rpm-pmi8998-regulators"; > + > + vdd_bob-supply = <&vph_pwr>; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3312000>; > + regulator-max-microvolt = <3600000>; > + }; > + }; > +}; > + > +&spmi_bus { > + pmic@0 { > + compatible = "qcom,pm8994", "qcom,spmi-pmic"; qcom,pm8994? Per the include of pm8998.dtsi I think you already have pmic@0 defined, with compatible of qcom,pm8998 here (which you override). > + reg = <0x0 SPMI_USID>; > + #address-cells = <1>; > + #size-cells = <0>; > + pon@800 { But pmic@0 already has pon@800 defined as &pm8998_pon, which seems to be defined identically to yours. So I think you should be able to drop this entire &spmi_bus node and its children, but perhaps I'm just missing something obvious here? > + compatible = "qcom,pm8916-pon"; > + > + reg = <0x800>; > + mode-bootloader = <0x2>; > + mode-recovery = <0x1>; > + > + pwrkey { > + compatible = "qcom,pm8941-pwrkey"; > + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; > + debounce = <15625>; > + bias-pull-up; > + linux,code = <KEY_POWER>; > + }; > + }; > + }; > +}; > + > +&tlmm { > + gpio-reserved-ranges = <0 4>, <81 4>; > +}; > + > +/* > + * The device does contain a USB3 capable type-c port, > + * however it doesn't seem to work when superspeed mode is > + * enabled. > + */ > +&usb3 { > + status = "okay"; > + > + /* Operate "GCC_USB30_MASTER_CLK" in HS mode (>=60 MHz) */ > + assigned-clock-rates = <19200000>, <60000000>; > + > + /* Disable USB3 pipe_clk requirement */ > + qcom,select-utmi-as-pipe-clk; > +}; > + > +&usb3_dwc3 { > + /* Drop USB 3 SuperSpeed PHY to bring up the "usb0" interface */ > + phys = <&qusb2phy>; > + phy-names = "usb2-phy"; > + > + /* We can only operate at USB 2.0 speeds */ > + maximum-speed = "high-speed"; > + > + /* Force to peripheral until we have Type-C hooked up */ > + dr_mode = "peripheral"; > +}; > + > +&ufshc { > + vcc-supply = <&vreg_l20a_2p95>; > + vccq-supply = <&vreg_l26a_1p2>; > + vccq2-supply = <&vreg_s4a_1p8>; > + vcc-max-microamp = <750000>; > + vccq-max-microamp = <560000>; > + vccq2-max-microamp = <750000>; > +}; > + > +&ufsphy { > + vdda-phy-supply = <&vreg_l1a_0p875>; > + vdda-pll-supply = <&vreg_l2a_1p2>; > + vddp-ref-clk-supply = <&vreg_l26a_1p2>; > + vdda-phy-max-microamp = <51400>; > + vdda-pll-max-microamp = <14600>; > + vddp-ref-clk-max-microamp = <100>; > + vddp-ref-clk-always-on; > +}; > + > +&wifi { > + status = "okay"; > + Can you please disable diag-router and try adding this here instead: clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>, <&rpmcc RPM_SMD_QDSS_CLK>; clock-names = "cxo_ref_clk_pin", "qdss"; What you describe in your comment above seems like what I saw on sm8150, that launching diag-router would cause something on the modem side to keep the debug subsystem clock on - which in turn caused WiFi not to crash during loading. I don't know why this was required, or if it's just working around some other issue we're having. Regards, Bjorn > + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; > + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; > +}; > -- > 2.29.2 > >
