From: Greg Kroah-Hartman <gre...@linuxfoundation.org>
From: Wolfram Sang <wsa+rene...@sang-engineering.com>
[ Upstream commit c7b514ec979e23a08c411f3d8ed39c7922751422 ]
To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+rene...@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+rene...@ragnatech.se>
Signed-off-by: Wolfram Sang <w...@kernel.org>
Signed-off-by: Sasha Levin <sas...@kernel.org>
---
drivers/i2c/busses/i2c-rcar.c | 11 ++++-------
1 file changed, 4 insertions(+), 7 deletions(-)
diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c
index 9c162a01a584..9d54ae935524 100644
--- a/drivers/i2c/busses/i2c-rcar.c
+++ b/drivers/i2c/busses/i2c-rcar.c
@@ -89,7 +89,6 @@
#define RCAR_BUS_PHASE_START (MDBS | MIE | ESG)
#define RCAR_BUS_PHASE_DATA (MDBS | MIE)
-#define RCAR_BUS_MASK_DATA (~(ESG | FSB) & 0xFF)
#define RCAR_BUS_PHASE_STOP (MDBS | MIE | FSB)
#define RCAR_IRQ_SEND (MNR | MAL | MST | MAT | MDE)
@@ -616,7 +615,7 @@ static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
/*
* This driver has a lock-free design because there are IP cores (at least
* R-Car Gen2) which have an inherent race condition in their hardware design.
- * There, we need to clear RCAR_BUS_MASK_DATA bits as soon as possible after
+ * There, we need to switch to RCAR_BUS_PHASE_DATA as soon as possible after
* the interrupt was generated, otherwise an unwanted repeated message gets
* generated. It turned out that taking a spinlock at the beginning of the ISR
* was already causing repeated messages. Thus, this driver was converted to
@@ -625,13 +624,11 @@ static bool rcar_i2c_slave_irq(struct rcar_i2c_priv *priv)
static irqreturn_t rcar_i2c_irq(int irq, void *ptr)
{
struct rcar_i2c_priv *priv = ptr;
- u32 msr, val;
+ u32 msr;
/* Clear START or STOP immediately, except for REPSTART after read */
- if (likely(!(priv->flags & ID_P_REP_AFTER_RD))) {
- val = rcar_i2c_read(priv, ICMCR);
- rcar_i2c_write(priv, ICMCR, val & RCAR_BUS_MASK_DATA);
- }
+ if (likely(!(priv->flags & ID_P_REP_AFTER_RD)))
+ rcar_i2c_write(priv, ICMCR, RCAR_BUS_PHASE_DATA);
msr = rcar_i2c_read(priv, ICMSR);
--
2.30.1
