Il 10/01/24 20:16, Konrad Dybcio ha scritto:
On 1/9/24 12:24, Luca Weiss wrote:
On Tue Jan 9, 2024 at 11:09 AM CET, Konrad Dybcio wrote:
On 1/5/24 15:54, Luca Weiss wrote:
Configure the thermals for the PA_THERM1, MSM_THERM, PA_THERM0,
RFC_CAM_THERM, CAM_FLASH_THERM and QUIET_THERM thermistors connected to
PM6150L.
Due to hardware constraints we can only register 4 zones with
pm6150l_adc_tm, the other 2 we can register via generic-adc-thermal.
Ugh.. so the ADC can support more inputs than the ADC_TM that was
designed to ship alongside it can?
And that's why the "generic-adc-thermal"-provided zones need to
be polled?
This part of the code from qcom-spmi-adc-tm5.c was trigerring if I
define more than 4 channels, and looking at downstream I can also see
that only 4 zones are registered properly with adc_tm, the rest is
registered with "qcom,adc-tm5-iio" which skips from what I could tell
basically all the HW bits and only registering the thermal zone.
ret = adc_tm5_read(chip, ADC_TM5_NUM_BTM,
&channels_available, sizeof(channels_available));
if (ret) {
dev_err(chip->dev, "read failed for BTM channels\n");
return ret;
}
for (i = 0; i < chip->nchannels; i++) {
if (chip->channels[i].channel >= channels_available) {
dev_err(chip->dev, "Invalid channel %d\n",
chip->channels[i].channel);
return -EINVAL;
}
}
The trip points can really only be considered as placeholders, more
configuration with cooling etc. can be added later.
Signed-off-by: Luca Weiss <luca.we...@fairphone.com>
---
[...]
I've read the sentence above, but..
+ sdm-skin-thermal {
+ polling-delay-passive = <1000>;
+ polling-delay = <5000>;
+ thermal-sensors = <&msm_therm_sensor>;
+
+ trips {
+ active-config0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
I don't fancy burnt fingers for dinner!
With passive trip point it wouldn't even do anything now, but at what
temp do you think it should do what? I'd definitely need more time to
understand more of how the thermal setup works in downstream Android,
and then replicate a sane configuration for mainline with proper
temperatures, cooling, etc.
If "skin therm" means "the temperature of some part of the phone's
body that can be felt with a human hand", then definitely some
throttling should happen at 40ish with heavy throttling at 50
and crit at 55 or so..
We should probably make this a broader topic and keep a single
policy for all supported phones.
+ CC AGdR, may be interested in where this leads
Konrad
A thermal trip at 125°C for *skin temperature* is useless... if a device's skin
temperature (be it a smartphone, a SBC, a Chromebook, a non-specially-identified
laptop, a car head unit, or whatever else you can imagine) reaches that kind of
temperature, this means that something inside likely reached something along the
lines of 150°C for a prolonged period of time.
You will definitely agree with me that if something reached that temperature for
a certain period of time, it is *highly unlikely* (not to say impossible) that
Linux is even still running and that the green smoke that is naturally trapped
in
any chip didn't get released :-)
Besides, keep in mind that if the SKIN temperature is 55°C, if your device has
a -> lithium <- battery (li-ion/lifepo/others), your hands are "probably" in a
kind of danger that I wouldn't be comfortable with (and neither you I'm sure).
Strictly related to the trip temperature setting for "SKIN", for me this is a
strong NAK.
I'd go for stricter ranges too, something like...
- critical: ~52/53
- heavy throttling: 49/50
- throttle: ~45
NOTE: this would be valid only if there are other throttling points for
CPU/GPU/etc
---- Anyway, something else I have in my mind: ----
Konrad: "standardizing" skin temperature is too big of a bet, and will be wrong,
because industrial-grade devices are permitted to reach higher skin
temperatures.
Some industrial grade smartphones (example: rugged stuff) may have sensors in
the underside of the ruggedized shell... so in that case you want to set the
skin
temperature limit with delta-T ideally...
Though!
Making this easier for everyone: we can somehow dictate (unofficially, because
of more of the many reasons I already explained) an acceptable temperature range
for "skin" temperature, outside of which, reviews should follow manual testing.
As for the concept of "skin temperature", and for some thermal framework work
(sorry for the word game) that I'm bringing on the table, in this case we can
imagine it as:
Thermal zone type: SKIN
Thermal zone name: shell-upper/shell-rightmost/shell....something
Type SKIN would be defined as
"a zone defining the temperature of the outer shell of a device"...
...and for example differently from type PCB, which fits different temperature
probe points.
Feel free to keep me in the loop, btw.
Cheers,
Angelo
