Hello, Please find my comment below:
On 11/21/25 8:21 AM, Valentina Fernandez wrote: > Microchip family of RISC-V SoCs typically have one or more application > clusters. These clusters can be configured to run in an Asymmetric > Multi Processing (AMP) mode. > > Add a dt-binding for these application clusters. > > Signed-off-by: Valentina Fernandez <[email protected]> > --- > .../microchip,ipc-sbi-remoteproc.yaml | 95 +++++++++++++++++++ > 1 file changed, 95 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/remoteproc/microchip,ipc-sbi-remoteproc.yaml > > diff --git > a/Documentation/devicetree/bindings/remoteproc/microchip,ipc-sbi-remoteproc.yaml > > b/Documentation/devicetree/bindings/remoteproc/microchip,ipc-sbi-remoteproc.yaml > new file mode 100644 > index 000000000000..348902f9a202 > --- /dev/null > +++ > b/Documentation/devicetree/bindings/remoteproc/microchip,ipc-sbi-remoteproc.yaml > @@ -0,0 +1,95 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: > http://devicetree.org/schemas/remoteproc/microchip,ipc-sbi-remoteproc.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Microchip IPC Remote Processor > + > +description: > + Microchip family of RISC-V SoCs typically have one or more > + clusters. These clusters can be configured to run in an Asymmetric > + Multi Processing (AMP) mode where clusters are split in independent > + software contexts. > + > +maintainers: > + - Valentina Fernandez <[email protected]> > + > +properties: > + compatible: > + const: microchip,ipc-sbi-remoteproc > + > + mboxes: > + description: > + Microchip IPC mailbox specifier. To be used for communication with > + a remote cluster. The specifier format is as per the bindings, > + Documentation/devicetree/bindings/mailbox/microchip,sbi-ipc.yaml > + maxItems: 1 > + > + memory-region: > + minItems: 1 > + maxItems: 5 > + description: > + List of phandles to the reserved memory regions associated wih the > remoteproc > + device. This is variable and describes the memories shared with the > remote cluster > + (e.g. firmware, resource table, rpmsg vrings, etc.) > + items: > + anyOf: > + - description: region used for the resource table when firmware is > started by the bootloader > + - description: region used for the remote cluster firmware image > section > + - description: virtio device (vdev) buffer > + - description: virtqueue for sending messages to the remote cluster > (vring0) This is in-accurate as per the implementation: https://github.com/torvalds/linux/blob/a919610db43b34621d0c3b333e12db9002caf5da/drivers/rpmsg/virtio_rpmsg_bus.c#L878 Also the implementation can be changed. The description doesn't need to mention if vring0 is used for rx or tx. > + - description: virtqueue for receiving messages from the remote > cluster (vring1) Same here. > + > + memory-region-names: > + minItems: 1 > + maxItems: 5 > + items: > + anyOf: > + - const: rsc-table > + - const: firmware > + - const: buffer > + - const: vring0 > + - const: vring1 > + > +required: > + - compatible > + - mboxes > + - memory-region > + - memory-region-names > + > +additionalProperties: false > + > +examples: > + - | > + // Early boot mode example - firmware started by bootloader > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + remoteproc { > + compatible = "microchip,ipc-sbi-remoteproc"; > + mboxes= <&ihc 8>; In the driver, this "mboxes" id is used for powering on/off remote processor. I think, "power-domains" is more suitable property over "mboxes" for this purpose. It is possible to only load, start and stop remote processor without any communication. So ideally "mboxes" can be optional, but in this case it can't be because remote's power-domain id is used from "mboxes" id. Even if both are the same number, they should be different properties and should be used for different purpose. Thanks, Tanmay > + memory-region = <&rsctable>, <&vdev0buffer>, > + <&vdev0vring0>, <&vdev0vring1>; > + memory-region-names = "rsc-table", "buffer", > + "vring0", "vring1"; > + }; > + }; > + > + - | > + // Late boot mode example - firmware started by Linux (remoteproc) > + soc { > + #address-cells = <2>; > + #size-cells = <2>; > + > + remoteproc { > + compatible = "microchip,ipc-sbi-remoteproc"; > + mboxes= <&ihc 8>; > + memory-region = <&cluster_firmware>, <&vdev0buffer>, > + <&vdev0vring0>, <&vdev0vring1>; > + memory-region-names = "firmware", "buffer", > + "vring0", "vring1"; > + }; > + }; > +...
