From: Qiang Liu <qiang....@freescale.com>
Move the function fsldma_cleanup_descriptor() and fsl_chan_xfer_ld_queue()
ahead of its invoke function for avoiding redundant definition.
Cc: Dan Williams <dan.j.willi...@intel.com>
Cc: Vinod Koul <vinod.k...@intel.com>
Cc: Li Yang <le...@freescale.com>
Signed-off-by: Qiang Liu <qiang....@freescale.com>
---
drivers/dma/fsldma.c | 252 +++++++++++++++++++++++++-------------------------
1 files changed, 124 insertions(+), 128 deletions(-)
diff --git a/drivers/dma/fsldma.c b/drivers/dma/fsldma.c
index 87f52c0..bb883c0 100644
--- a/drivers/dma/fsldma.c
+++ b/drivers/dma/fsldma.c
@@ -400,9 +400,6 @@ out_splice:
list_splice_tail_init(&desc->tx_list, &chan->ld_pending);
}
-static void fsldma_cleanup_descriptor(struct fsldma_chan *chan);
-static void fsl_chan_xfer_ld_queue(struct fsldma_chan *chan);
-
/**
* fsldma_clean_completed_descriptor - free all descriptors which
* has been completed and acked
@@ -519,6 +516,130 @@ fsldma_clean_running_descriptor(struct fsldma_chan *chan,
return 0;
}
+/**
+ * fsl_chan_xfer_ld_queue - transfer any pending transactions
+ * @chan : Freescale DMA channel
+ *
+ * HARDWARE STATE: idle
+ * LOCKING: must hold chan->desc_lock
+ */
+static void fsl_chan_xfer_ld_queue(struct fsldma_chan *chan)
+{
+ struct fsl_desc_sw *desc;
+
+ /*
+ * If the list of pending descriptors is empty, then we
+ * don't need to do any work at all
+ */
+ if (list_empty(&chan->ld_pending)) {
+ chan_dbg(chan, "no pending LDs\n");
+ return;
+ }
+
+ /*
+ * The DMA controller is not idle, which means that the interrupt
+ * handler will start any queued transactions when it runs after
+ * this transaction finishes
+ */
+ if (!chan->idle) {
+ chan_dbg(chan, "DMA controller still busy\n");
+ return;
+ }
+
+ /*
+ * If there are some link descriptors which have not been
+ * transferred, we need to start the controller
+ */
+
+ /*
+ * Move all elements from the queue of pending transactions
+ * onto the list of running transactions
+ */
+ chan_dbg(chan, "idle, starting controller\n");
+ desc = list_first_entry(&chan->ld_pending, struct fsl_desc_sw, node);
+ list_splice_tail_init(&chan->ld_pending, &chan->ld_running);
+
+ /*
+ * The 85xx DMA controller doesn't clear the channel start bit
+ * automatically at the end of a transfer. Therefore we must clear
+ * it in software before starting the transfer.
+ */
+ if ((chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) {
+ u32 mode;
+
+ mode = DMA_IN(chan, &chan->regs->mr, 32);
+ mode &= ~FSL_DMA_MR_CS;
+ DMA_OUT(chan, &chan->regs->mr, mode, 32);
+ }
+
+ /*
+ * Program the descriptor's address into the DMA controller,
+ * then start the DMA transaction
+ */
+ set_cdar(chan, desc->async_tx.phys);
+ get_cdar(chan);
+
+ dma_start(chan);
+ chan->idle = false;
+}
+
+/**
+ * fsldma_cleanup_descriptor - cleanup and free a single link descriptor
+ * @chan: Freescale DMA channel
+ * @desc: descriptor to cleanup and free
+ *
+ * This function is used on a descriptor which has been executed by the DMA
+ * controller. It will run any callbacks, submit any dependencies, and then
+ * free the descriptor.
+ */
+static void fsldma_cleanup_descriptor(struct fsldma_chan *chan)
+{
+ struct fsl_desc_sw *desc, *_desc;
+ dma_cookie_t cookie = 0;
+ dma_addr_t curr_phys = get_cdar(chan);
+ int idle = dma_is_idle(chan);
+ int seen_current = 0;
+
+ fsldma_clean_completed_descriptor(chan);
+
+ /* Run the callback for each descriptor, in order */
+ list_for_each_entry_safe(desc, _desc, &chan->ld_running, node) {
+ /*
+ * do not advance past the current descriptor loaded into the
+ * hardware channel, subsequent descriptors are either in
+ * process or have not been submitted
+ */
+ if (seen_current)
+ break;
+
+ /*
+ * stop the search if we reach the current descriptor and the
+ * channel is busy
+ */
+ if (desc->async_tx.phys == curr_phys) {
+ seen_current = 1;
+ if (!idle)
+ break;
+ }
+
+ cookie = fsldma_run_tx_complete_actions(desc, chan, cookie);
+
+ if (fsldma_clean_running_descriptor(chan, desc))
+ break;
+ }
+
+ /*
+ * Start any pending transactions automatically
+ *
+ * In the ideal case, we keep the DMA controller busy while we go
+ * ahead and free the descriptors below.
+ */
+ fsl_chan_xfer_ld_queue(chan);
+
+ if (cookie > 0)
+ chan->common.completed_cookie = cookie;
+}
+
static dma_cookie_t fsl_dma_tx_submit(struct dma_async_tx_descriptor *tx)
{
struct fsldma_chan *chan = to_fsl_chan(tx->chan);
@@ -932,131 +1053,6 @@ static int fsl_dma_device_control(struct dma_chan *dchan,
}
/**
- * fsldma_cleanup_descriptor - cleanup and free a single link descriptor
- * @chan: Freescale DMA channel
- * @desc: descriptor to cleanup and free
- *
- * This function is used on a descriptor which has been executed by the DMA
- * controller. It will run any callbacks, submit any dependencies, and then
- * free the descriptor.
- */
-static void fsldma_cleanup_descriptor(struct fsldma_chan *chan)
-{
- struct fsl_desc_sw *desc, *_desc;
- dma_cookie_t cookie = 0;
- dma_addr_t curr_phys = get_cdar(chan);
- int idle = dma_is_idle(chan);
- int seen_current = 0;
-
- fsldma_clean_completed_descriptor(chan);
-
- /* Run the callback for each descriptor, in order */
- list_for_each_entry_safe(desc, _desc, &chan->ld_running, node) {
- /*
- * do not advance past the current descriptor loaded into the
- * hardware channel, subsequent descriptors are either in
- * process or have not been submitted
- */
- if (seen_current)
- break;
-
- /*
- * stop the search if we reach the current descriptor and the
- * channel is busy
- */
- if (desc->async_tx.phys == curr_phys) {
- seen_current = 1;
- if (!idle)
- break;
- }
-
- cookie = fsldma_run_tx_complete_actions(desc, chan, cookie);
-
- if (fsldma_clean_running_descriptor(chan, desc))
- break;
-
- }
-
- /*
- * Start any pending transactions automatically
- *
- * In the ideal case, we keep the DMA controller busy while we go
- * ahead and free the descriptors below.
- */
- fsl_chan_xfer_ld_queue(chan);
-
- if (cookie > 0)
- chan->common.completed_cookie = cookie;
-}
-
-/**
- * fsl_chan_xfer_ld_queue - transfer any pending transactions
- * @chan : Freescale DMA channel
- *
- * HARDWARE STATE: idle
- * LOCKING: must hold chan->desc_lock
- */
-static void fsl_chan_xfer_ld_queue(struct fsldma_chan *chan)
-{
- struct fsl_desc_sw *desc;
-
- /*
- * If the list of pending descriptors is empty, then we
- * don't need to do any work at all
- */
- if (list_empty(&chan->ld_pending)) {
- chan_dbg(chan, "no pending LDs\n");
- return;
- }
-
- /*
- * The DMA controller is not idle, which means that the interrupt
- * handler will start any queued transactions when it runs after
- * this transaction finishes
- */
- if (!chan->idle) {
- chan_dbg(chan, "DMA controller still busy\n");
- return;
- }
-
- /*
- * If there are some link descriptors which have not been
- * transferred, we need to start the controller
- */
-
- /*
- * Move all elements from the queue of pending transactions
- * onto the list of running transactions
- */
- chan_dbg(chan, "idle, starting controller\n");
- desc = list_first_entry(&chan->ld_pending, struct fsl_desc_sw, node);
- list_splice_tail_init(&chan->ld_pending, &chan->ld_running);
-
- /*
- * The 85xx DMA controller doesn't clear the channel start bit
- * automatically at the end of a transfer. Therefore we must clear
- * it in software before starting the transfer.
- */
- if ((chan->feature & FSL_DMA_IP_MASK) == FSL_DMA_IP_85XX) {
- u32 mode;
-
- mode = DMA_IN(chan, &chan->regs->mr, 32);
- mode &= ~FSL_DMA_MR_CS;
- DMA_OUT(chan, &chan->regs->mr, mode, 32);
- }
-
- /*
- * Program the descriptor's address into the DMA controller,
- * then start the DMA transaction
- */
- set_cdar(chan, desc->async_tx.phys);
- get_cdar(chan);
-
- dma_start(chan);
- chan->idle = false;
-}
-
-/**
* fsl_dma_memcpy_issue_pending - Issue the DMA start command
* @chan : Freescale DMA channel
*/
--
1.7.5.1
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
